Atom n450 and applying Arctic Thermal tips

samm

[H]ard|Gawd
Joined
Jul 17, 2013
Messages
1,757
So not a "insane" build question regards to cooling, as its an Atom but first time dealing with laptops thermal pastes. So had to get a new mb that comes with the atom soldered on it. Now when I pulled the fan from the old MB it seems as it was attached by a T-Pad. I don`t have access to good T-Pads but I do have a new unused arctic silver paste lying around. I did search their website for instruction, but under Intel no mention of Atom processors, so now im here.

Anyone have any tips on how to apply.

Due to the relatively small processor surface area a rice grain size drop of Arctic will work, but again not sure.
 
I'd be wary of using paste in place of a thermal pad, because if the gap between the heatspreader and the heatsink is great enough, the thick layer of paste required would likely not transfer heat nearly as well. It might be worth trying to reuse the thermal pad if possible.

Something I've heard of somebody doing on an older Atom netbook (Lenovo S10, which I'm actually typing this on) was lap a penny and use that to fill the gap (with thermal paste on both sides of the penny of course). They actually did it because of a factory defect where even with the thermal pad the gap on the gpu was too large and it overheated, but I could imagine doing something similar here in lieu of a thermal pad. If you got it just right it'd probably actually transfer heat a lot better.
 
Like CapnCrunch mentioned, check if there is a gap that doesn't close. Many laptop cooling solutions do not fully contact the core, and leave a small gap for the thermal pad.

If you can confirm that the cooling solution can fully press against the core, then just following standard application protocol

1) If it's a heatspreader, do a cross or a line, and let the cooling solution squeeze out the bubbles as it press on

2) If it's a bare die, you can either use the pea size method, or apply a thin layer to the entire die.

(make sure the arctic silver doesn't touch any electrical components or contacts.)
 
The gap would be the key part as everyone has said. But please use some decent thermal paste. I have no idea why people insist on still using that crappy arctic silver for thermal compound. Spend a little money and get some good thermal compound that doesn't have to cure. We aren't living in 2003 anymore.
 
Thanks for the responses, really do appreciate it.

So update notes:

The reason Im reapplying this is the old MB got fried (I tried trouble shooting the board, but I got no where as no posts except for maybe twice randomly out of maybe 50 tries). So new MB shipped, and the atom is obviously soldered.

When i recycled the old cooling solution this is what I got:
1) The fan is attached to a metal sheet
2) The fan is positioned on the left of the cpu, so no direct contact.
3) The CPU cooling solution is literally just a piece of metal that mates with the top of the CPU. No complicated cooper heat sinks or tubing of any sort that I have seen on other lappies.
4) The thermal compound that mated the CPU to the piece of metal heatsink I cannot specifically identify. It doesnt seem like a pad as its not intact, seems more of a putty compound. Now I could be wrong here but it just doesnt seem like a pad.

My installation (trial 1):
1) I removed the fan metal unit. it was clean, but i still went ahead and Isopropyl cleaned it.
2) The cpu had a mirror finish, but again cleaned that.
3) Applied the rice grain in the middle, spread it with a cleaned credit card. very thin layer.
4) Did not test fit, and stress tested it with P95.
Results: Bad mounting. Tests temperatures indicated I was running near 80C on the Core temps, and MB thermal should 65-70 C temps on the MB at 100% load. From my previously saved thermal points this was way out of spec. Fan blaring at 100%.

My installation (trial 2):
1) I removed the fan metal unit. it was clean, but i still went ahead and Isopropyl cleaned it.
2) The cpu cleaned that.
2.5) Mounted the Fan unit on top of the CPU to see what kind of gap I was working with. Noted.
3) Applied a grain in the middle but more this time. No spreading, just applied the fan unit in a level proc.
4) Stress tested it with P95.
Results: Good and Bad mounting. Tests temperatures indicated I was running near 60C on the Core temps, BUT THE MB thermal shows 60 C temps. From my previous data sets, the Core Temp is good even a few degrees lower than usual. When P95 was ended, core temps decreased to 40C which again is good. BUT The kicker however is that my MB Temps dont decrease as they should be when idling. And I have absolutely zero clue why. The only thing that has a thermal interface cooling solution is the CPU. Everything else is passive....Im hoping its a pre-burn in thing, but EHH?


Using Arctic Ceramique 2. I have heard about the penny trick, but I fear the penny slipping and shorting something out. Another idea was copper shims but again same fear. Thermal pads, when I ordered the paste was hard to find. Newegg had some terribly rated Startechs. I finally found frozens t-pads, but am only going to order it if need be. Im following the service manual from the MFG, and they actually either recommend two types of thermal paste or a one thermal pad. So paste seems ok, but Im guessing the arctic is different in composition.

Hoping some more break-in testing will cure the MB problem, or if not, ordering a set of T pads
 
trial 3 looks like its a winner thus far. Compared to my old data points on the old MB, Im seeing a 3-4 point difference in Board temps. The Core temps are a bit higher 10-13 points here, but only when Im torture testing the CPU. In general usage such as streaming and etc i have maybe a 5-6 point difference. Those numbers seem in line with Arctic's pre-break in numbers.

Again worst comes to worst T-pads from fujipoly (extreme 11m/wk)
 
Back
Top