ASUS P7P55D-E SATA controllers?

SirJohn

n00b
Joined
Oct 9, 2009
Messages
12
I just bought this board last weekend at Microcenter with an i7-860. I put the rig together and attached two Seagate 1TB to the first two SATA ports (of the 6 near the one jmicron controller SATA port). I then attached the two optical drives to the top ports (Marvell).
When I tried to boot for the first time, the BIOS would stop at "configuring marvell controller" for a long time and then nothing. I was unable to even enter the setup. I heard no beeps because the case didn't seem to come with a speaker?!?
So I cleared CMOS, still the same. Finally I moved the opticals to SATA 3 and 4 and it booted normally and allowed me to both enter BIOS and boot to DVD.
Can someone explain why this occurred? What do I have to do to make use of these Marvell controller ports?
I am still waiting for a 64-bit Win 7 DVD so I haven't tried anything else yet.

Also, this is my first build in 6 years so I am a bit rusty. If anyone has suggestions on how to set up my drives most efficiently I would appreciate hearing from you. I originally thought of RAID 1 then setting two partition, one 250GB and the other 750GB, then had second thoughts. Maybe simpler is better? The board also has a legacy IDE drive but will I gain anything by using it? I may decide to re-work things when SSD becomes more affordable.
I am especially interested in the 1 jmicron and 2 Marvell ports. What is the purpose for these? I know the Marvells are the high speed ports, but since I have mechanical HDs they are not much use to me yet.
FYI I have about 500GB of data I want to move to the PC after its set up.

Specs are:

Antec 300 case
Antec Earthwatts 650 PS
P7P55D-E ASUS mobo
2x2GB OCZ DDR3 1600
i7-860 processor
XFX 5770 ATI card
Seagate 1TB x 2
2 SATA optical drives
 
Last edited:
make sure that all the correct controllers are enabled in bios. also that you have the correct controller mode set, ie acpi, acpi + ide, raid, legacy ide, etc.

you really should get another drive for boot/aps. then set up your 1tb drives in raid 1, without partitions. you can buy a really fast 500/640gb drive for $55 to $70 now. also, the intel 40gb ssd is on sale for around $100, or at least it was over the weekend.
i am going to go with a 30 or 40gb ssd for my os and favorite game/s and apps, then either 1 80gb vraptor or 2 80gb in raid 0 for the rest of my games and apps, then a raid 1 or 5 array for my data.
i wouldnt use the ide port unless i had to.
 
Last edited:
I see, so I would have to initially boot from the SATA port 1 and then move the opticals after the controller for Marvell is enabled. I have to check on that.
I don't think I can get away with a small OS drive. I have an 80GB on my old PC and it's about 60GB full just with programs. Yeah I suppose I could install on the data drives but then I have to worry about drive letters changing. And aren't larger mechanical drives faster because the data is more dense on the platters?
OK so say I go with your idea, which SATA ports/controllers should I use for which drives for best efficiency?
Is it possible to use the 2 SATA 6 (Marvell) ports for booting (say when I upgrade to SSD)?
Wouldn't it be best to spread my SATA devices accross all controllers to reduce bottlenecks?
Thanks for the reply.
John
 
Last edited:
Not that anyone else seems to care, but I got an official answer (of sorts) from ASUS support:

My question:
I am confused by the SATA ports. What are recommended usage for jmicron and
Marvell controllers? I tried putting Optical drives on Marvel ports and could not boot
(hung at configuring Marvell controller at POST).
Seems I am safe just using SATA ports 1 to 6 but then what good are jmicon and
Marvell ports?
Please tell me the most optimal configuration. I have two 1TB mechanical hard drives
and two SATA optical drives.

ASUS answer:
"that controller is normally for secondary hard drives (data hard drives) normally my bootable and dvd drives will be on the intel controller"
 
Back
Top