ASUS MB Not Recognizing CPU?

Daras

n00b
Joined
Apr 20, 2004
Messages
3
First, my system specs:
Athlon XP 3000+/ Barton 333
Asus A7V8X-X, BIOS ver 1009, 4-in-1 ver 449
Corsair XMS DDR PC3200 @333
GF FX5700 Ultra/128
Windows XP, SP1
Antec case and PSU @350w

I recently upgraded my cpu to the Barton listed above. When I booted up, I entered the BIOS to check my settings.
I checked the FSB speed. It was set at 166/33 with a multiplier of 13. VCore is 1.65. CPU Speed is set to "Manual". Everything seemed ok.
I used Sandra to do a check on the cpu. It said that the cpu is at 1.750ghz. I thought this odd because this model of the Barton chip runs at 2.167ghz. I checked the model number on the Athlon and confirmed that it is the correct one.
I did a benchmark in Sandra and compared it with an Athlon XP 3000+ (as a baseline), the Athlon XP 2000+, and the Pentium4 2.8. Results showed that it was running no faster than the Athlon XP 2000+.
So, I double check these results with 3DMark03. It also says that my cpu is running at 1750. I ran a benchmark and I see that the results are nearly identical to the results I got with my old cpu (Athlon XP 2000+) when I should be seeing about a 30% increase in speed.
I checked out the ASUS website and it was no help at all. It shows that this model MB supports this cpu. This MB is jumperless for FSB settings, so there's nothing I can do in this regard.
What's wrong here? Should my BIOS settings be different? Is the MB not seeing the cpu properly?
 
Did you update your BIOS? If this isn't a new board you should reset the CMOS settings by clearing the CMOS and then let it detect the new CPU.

If not there could be something wrong with your CPU or your board.

I have seen CPU's that were going bad clock less than they should.
 
The BIOS version is listed above. It is the latest version.
I didn't clear the settings before the install. I'll try that and post results.
 
Also you can try reflashing the BIOS because sometimes the BIOS can be a little messed up and appear to be working.
 
Followup:
I reflashed the BIOS with ver 1009. No change.
I pulled the battery and reset the CMOS to default. I then rebooted. BIOS settings manually restored to previous settings. CPU Speed set to manual. FBS set to 166/33. Multiplier at 13. Memory synched @333.

Sandra reports the FBS as being @333. CPU still appearing as 1.750ghz. CPU still running like a 2000+, instead of a 3000+.
I figure that this could be one of two different problems.
1) The CPU is not a true Athlon. I doubt this because the die is most definitely an AthlonXP/Barton, as it has the correct dimensions and the correct model number stamped on it. I compared it to the illustrated models on the Athlon website, and it checks out.
2) The MB is faulty. This may be the most likely reason. Programs like Sandra and 3DMark only read the BIOS info, they don't actually measure the FBS speed (or do they?). I'm guessing that maybe the MB BIOS "thinks" it's FBS is set to 333, when it might actually be running at 266. However, the Memory speed does appear to be running at 333, as testing of the memory shows my Corsairs as being on par with the test standards for similar memory.

If number two is correct, would it be possible to boost the multiplier and/or VCore settings to compensate for this? Can this be done safely, without doing harm to my RAM and other components? Or should I just play it safe and assume that the MB is faulty and invest in a new board? ( I don't like this idea, as the MB is only 8 months old and the wife would have a hissyfit if she sees me buying another one so soon :rolleyes: )
 
I think your motherboard doesn't know how to do math... try a different timing and see if it's math gets better... 165 x13 multiplier or similar. 13x166 is 2,167. I don't know what there is to try other than reseating the processor.
 
If the CPU is showing as 1750 Mhz, then that’s 133 x 13 NOT the proper 166 x 13. Something is wrong with your FSB speed.

Asus boards have had a problem recognizing Barton Core CPUs. My A7N8X Deluxe v1.04 exhibits this problem. No matter what BIOS I use, (even an Uber BIOS). It wants to recognize Barton 2500 (166 x 11) as a 133 x 11 CPU. The solution is to manually go into the CPU settings and set the proper FSB speed and Multi, then SAVE, and SAVE and EXIT. When the system reboots it should show the proper settings.

If that doesn’t work does this board have a jumper for selecting between FSB speeds? You might want to check that.

Also, NForce2 boards from Asus have a tendency to eat CMOS batteries, the board nay not be holding settings. Check you CMOS battery voltage. A new hot battery is 3.3 volts, anything below 3v is time for a replacement, and they’re only $3 anywhere.

BTW, did you use something like this to check your CPU?
 
Back
Top