Assistance needed with new build

vdubbia

n00b
Joined
Aug 22, 2007
Messages
30
Abit IP35E
e6750 w/ stock sink
G.Skill 4x1GB DDR 800
OEM Vista x64
Earthwatts 500w
8800GTS 320

I built system and successfully posted, but I can't seem to get to the point where I can actually install the OS.

When I save my BIOS settings, I just get to a black screen with no prompts whatsoever. I put the Vista DVD in my burner, restart the system, green light flickers on my drive, but HDD does not spin. All power is connected, all board connections are connected and are seen in BIOS.

Any ideas?
 
It might be your ram is rated for 2.1 volts and your motherboard is only puttin out 1.8?
I am not sure if that problem was fixed with some MB's.
 
What hard drive are you using? Don't see it in your post. Could be several different things, first try reseating everything, memory, cards, etc... If that does not help, change your memory sticks around, drop down 2 sticks, change them up, make sure it is not a dead memory stick. Could be a bad board, power supply, memory etc. If you have extra stuff laying around try swapping them out. Let us know what you find.
 
when I hit F1 to bypass BIOS set up, I get a white bar on the bottom of the screen that says 'Windows is loading files' but it stops at about 1/8 of the way across and just sits.
 
What hard drive are you using? Don't see it in your post. Could be several different things, first try reseating everything, memory, cards, etc... If that does not help, change your memory sticks around, drop down 2 sticks, change them up, make sure it is not a dead memory stick. Could be a bad board, power supply, memory etc. If you have extra stuff laying around try swapping them out. Let us know what you find.

HDD is: Seagate: HD 320G|ST 7K 16M SATA2 ST3320620AS
 
Have you tried a different sata port?

Sounds like a memory or hard drive failure to me. Another option is a boot disc that will check you memory and drives. A gentleman by the nick of Tmod, has a damn good one out. Bootable iso downloadable, gives you access to memtest, and several different HD makers drive utilities. Just google tmod and you should find it.
 
Progress!

I changed a SATA port and re-seated the SATA power cable and I got all the way through the 'loading files' screen and am now looking at an install screen... will keep you posted.

THANKS!
 
The reason I was getting the black screen was because I set my Init display to PCI vs. PCIe. Once I did that I was good to go.

I do think that the SATA connection was loose, too.

Thanks for the help... things seem to be moving along nicely at this point.
 
Ok... new issue.

During my BIOS setup I changed my DDR2 voltage from 1.8 to 1.95.

Vista booted, life was grand, I was able to do some benchmarking, etc. Played around with Vista for a good hour or so, downloaded the 32 updates I needed and installed, etc.

System rebooted, etc. and all was great.

Ran Speedfan and noticed a little flame icon next to AUX, figured that was RAM, so I went back into BIOS and lowered DDR2 voltage back down to 1.8. Now system won't boot. Tried going back to 1 stick, 2 sticks.... nothing.

Any suggestions? I can't get back into the BIOS now.

UGH!
 
well, I'm back in business. Reset the DDR2 to 1.95v and that gets me a quick boot.

How do I know if this voltage is optimum? My ram is rated 1.8-2.0v. Should I be happy as long as its stable and not burning up?
 
ground yourself, then touch the ram while your system is running... if you can keep your finger on it for over ten seconds, then its fine. :eek: it should be running warm, not scorching hot. if you can tolerate high heat, take that into account :p if its running super hot, lower the voltage a bit.
 
Back
Top