Are these voltages and temps safe?

ToyYoda03

ToyYoda03

[H]ard|Gawd
2FA
Joined
Jun 1, 2004
Messages
1,937
Currently priming right now, so for stable...is this ok?

is%20it%20safe.JPG
 
Did you swap out your chaintech vnf3-250? Yeah, those temps are fine. The voltage is also fine, but I always get a bit sketchy bumping mine past 1.65v. I'm a pussy though. I think the critical temps for the AMD64 are around 90c.
 
not too bad i dont think!.. nice o/c tho! wish i could get mine higher! (think my agp/pci is not locked :()
 
jubei said:
Did you swap out your chaintech vnf3-250? Yeah, those temps are fine. The voltage is also fine, but I always get a bit sketchy bumping mine past 1.65v. I'm a pussy though. I think the critical temps for the AMD64 are around 90c.
Click to expand...

Yeah I did swap it, I was tired of being motherboard limited :p
 
This might be a stupid question and if it is excuse my igorance. But how did you get your HTT to show over 300 while your mem is clocked to 217????
 
dabiggoober said:
This might be a stupid question and if it is excuse my igorance. But how did you get your HTT to show over 300 while your mem is clocked to 217????
Click to expand...

the ratio is really low
 
Nice stuff!
Temps are alright... should be a little cooler though :)
What are they on load?

And how low does your +12 line dip during load? You might want to be careful of that one...
If it's constantly at 11.60ish, and dips below 11.40 on load, you could have lots of problems...

:)
 
If those temps are under load, that's pretty good. That 12v rail does look a little low, but if that's under load it should be all right.

Basically, aim to keep your temperatures below 60C.

And that's a pretty good overclock there as well. What motherboad are you using now?
 
ohh i like that

man good overclock.

im currently running my 3200+ Clawhammer at 3.5ghz fsb = 350 HTT@3 cas at 3-3-3-8-7-16 wish there was a way to adjust the 16 but ,,,nope. the asus K8N-E Deluxe only has VDIMM up tp 2.7v but the ocz pc4000 allows me to have a lot of fsb room to play with.
VCore is 1.6.v.

i must say i am very happy with this setup. this smokes my old system. the one you see in my sig.
 
v_lestat said:
ohh i like that

man good overclock.

im currently running my 3200+ Clawhammer at 3.5ghz fsb = 350 HTT@3 cas at 3-3-3-8-7-16 wish there was a way to adjust the 16 but ,,,nope. the asus K8N-E Deluxe only has VDIMM up tp 2.7v but the ocz pc4000 allows me to have a lot of fsb room to play with.
VCore is 1.6.v.

i must say i am very happy with this setup. this smokes my old system. the one you see in my sig.
Click to expand...


1.5ghz OC on yours... thats pretty awesome...
 
oh shit i did it again hahaha
im so used to typing 3.5 cuz of my intel system

i mean 2.5ghz. so only a 500mhz overclock. but thats good for the amd 64's.

sorry bout the type-o
 
don_vercetti said:
If those temps are under load, that's pretty good. That 12v rail does look a little low, but if that's under load it should be all right.

Basically, aim to keep your temperatures below 60C.

And that's a pretty good overclock there as well. What motherboad are you using now?
Click to expand...

Its under load, see sig for mobo
 
You must log in or register to reply here.
Back
Top