Anything I can do to make this stable?

blade52x

2[H]4U
2FA
Joined
Sep 9, 2006
Messages
3,233
I would really, really, like to have 3.2Ghz stable on my E6600 :) It's so close right now, it failed Orthos blend test after 4 hours, and recently failed Orthos cpu only test after about an hour and 30 minutes. Before you say start raising the VCore, I am trying to get this right now without touching my VCore.

1- BIOS is version F7 (will F8 add any stability?)
2- I am tried 400x8 (will 356x9 be more stable then 400x8 - my RAM is not an issue)
3- Along with running a 400fsb, if I add .1V to the vfsb, will it help out stability? And will I need addtional cooling for the nb if I add +.1 to the fsb (asking DS3 owners here) - after immediate shutoff with 400x8, it was hot, but not that hot where I couldn't keep my finger on it.
4- VMch - When, and why to add voltage for this? And where will the temperatures go up?
5- Pushing PCI-e frequency up to 101-105Mhz - any more stable? Is it ok with ATI x1900xt GPUs? (which is already overclocked slightly, but without volt mods)

If all else fails I guess I'll probably slightly bump the Vcore :eek:
 
52-53C load - 1.325V

(I'm going to end up replacing my HS's fan with a stronger one which should drop the temps a little more)

I've been slightly above at 1.4325V before just for testing, and my load topped out at 62C, so I believe I do have some headroom as it is anyway.
 
Adding a tiny bit more Vcore could help.

Vfsb or the Front Side Bus Termination Voltage is good if you're going over 400fsb or so. Go ahead and try it. Make sure you RETURN IT BACK TO STOCK if it doesn't help. Screwing witht the Vfsb has been known to fry certain boards.

The new F8i bios is said to help alot with overclocking.

Going to 101mhz on the PCIe bus, is more than acceptible. It will help stability too. I run mine at 101. (system in sig, P5B-Deluxe at 500fsb).

the MCH voltage... I think... is the SB chipset. You shouldn't need more voltage here...

More cooling on the NB hsf shouldn't be necessary if you have good case ventilation. Wouldn't hurt, however.
 
Thanks for the reply.

I think it ended up being that a slight bump in VCore was the only way to go. The PCI-e at 101Mhz seemed to add a little stability (CPU test ran for an extra hour before it failed), so I left it there. Now running 1.35V, highest temps I've seen is 54C :)

I'll wait for the final release of F8. I don't really feel comfortable with beta bios.

If this ends up being stable (10 hours of Orthos is fine for me, still has 6 hours to go), then I will attempt to go 1000Mhz on the RAM (with 5-5-5-15 or better), and if that ends up being stable, I will be very, very happy!
 
I need about 1.350V for my E6600 at 8x400, it needs ~1.450V (1.4V actual) for 7x500

Every chip is different, but you are probably too low on your VCore for you OC.
 
este said:
I need about 1.350V for my E6600 at 8x400, it needs ~1.450V (1.4V actual) for 7x500

Every chip is different, but you are probably too low on your VCore for you OC.

Yeah, probably was.

I'm now 7 hours into the 400x8 CPU only test at 1.35V (CPU-Z is showing a constant 1.328V actual), so mine is probably similar to yours :) Thanks for the 3.5Ghz voltage, so I have a good estimate of what I'd need, but one question - did you try 400x9 or did the temperatures get to high?

I doubt my DS3 can hit 500FSB, I haven't seen to many people get them that high.
 
P5B only hits 500+ b/c of its strap getting way loose over 400. (400 is 1066, 401 is 1333, not sure if it goes above that) my SysTool always says 1067 so I don't know.

I can do 400x9 but it I haven't really tried to get the temps any lower. I think 3.5 is way easier on it then 3.6 so far.

One other thing is P5Bs can NOT do 4:5 over at 400+ so until thats fixed its 1:1 for me.

I figured if I'm going to OC I'm going to get the chip and ram working, not just one or the other. I personally could not care even a little about 200Mhz either way. I'm working on my 24/7 clock, not a penis size contest OC chart.

I like 500x7 for cpu and ram. Seems like a balance to me, although it I could keep the strap at 1066 and thus limit my oc to 500Mhz or below that would be fine too. So you should be fine since I don't think the DS3 has the same issues as the P5B
 
5007x7 is a good balance IMO... I can boot at 525 * 7, and complete about 6 hours of Orthos before failing... But to do that my Vcore needs to be 1.5v BIOS, 1.4875 actual.

Wayy too high IMO... the extra 150mhz just isn't worth it.
 
That sounds like about the voltage I would need for 525Mhz. But, you are right the added little speed (which won't really make any difference real world) isn't worth it.


I wish Sandra would run on my machine, all I have is Systool for memory benchmarks and all that tells me is 6900 or 7300MB/s (400Mhz or 500Mhz). I have no idea if thats good or not, nor what anyone else is getting.

But I'm sure whatever the difference its just splitting hairs. I think I may go back down to 3.2Ghz and tight memory for 24/7. At least until the P5B issues get fixed. Then I like the idea of 3.4 and tight timings
 
Going from CAS 5 to Cas 4 netted me an entire second in super pi 1M.

Going from 3300 to 3500 only netted me about... 1/2 a scond in Super Pi 1M...


Superpi's not the best benchmark, but tighter timings do make a difference.
 
Back
Top