Antec 430 True...hot air??

Klync

Limp Gawd
Joined
Jun 11, 2003
Messages
133
sup yo,

Gezz does anyone have this PSU? Mine blown hot air. Its this normal? I have a Lian Li pc-60 case w/ tose 4 stock fans. Why this Antec true 430 blowing hot air. I know its controlled by the heat sensor. Mine Enermax 350 blow nice and cool air. Dont get me wrong, thise 430 psu is awesome.

Anyone know this issue?

thank
ken
 
is it by chance exhausting the hot air produced by the CPUs Heatsink?
Per the AMD Buiders Spec?

In addition the more your powering with it the more its own inefficiency adds up
(where its efficency is say 70% that means 30% is directly converted to heat)

and finally heat transfer is all about temperature differential
if your ambient and case temp is high, the efficency of your thermal solution decreases, and the internal heatsinks maintain a higher temperature

General Heat Transfer Guide @ amdmb written specifically about the thermodynamics of computers, and focusing on aircooling
ProCooling Article base well worth a browse, also check the forum and specifically the ProCooling Staff Worklogs

one of the things you can draw from the first article is
The heat transfer through the wall follows a simple equation:
Q=k/L(T1-T2)

my comments below in italics
We can draw some interesting conclusions from this equation. First, heat transfer is proportional to the temperature difference on the object. If the temperature differential doubles, the heat transferred doubles.If the temperature of your air is colder the efficiency increases Second, the conduction coefficient "k" is proportional to heat transfer. If the conduction coefficient doubles, the heat transfer doubles.Applys to the material, generally copper, which has a better conduction coefficient than say aluminum Alternatively, for the same differential temperature, twice as much heat may be transferred. The final observation is "L". As thickness increases, heat transfer decreases. Alternatively, to maintain the same heat transfer through a material twice as thick requires twice the temperature differential.

that happens to be for conduction, but there is a corollary for convection (transfer from the heatsink to a fluid (air\water\ect)
its known as Newton's Law of Cooling

so what the hell is my point? :p
whatever thermal solution you have is typically rated with a °C/W rating (Thermal Resistance (Rht) in °C/W actually)

Delta = CPU temp - Ambient Temp
C/W = Delta / CPU Watts

Interpreting C/W: For every watt (CPUw) that the CPU consumes, the HSF will limit the CPU's temperature rise to (C/W x CPUw) plus the temperature at the HSF's fan inlet. For example, at an ambient temp of 25 C, a C/W of 0.25 with a CPU radiating 50 watts means that CPU temp will increase 50 x 0.25 = 12.5 C over ambient temp, or 37.5 C. The lower the C/W, the better.
and the lower the Ambient Temperature too
basically the thermal resistance of a given solution changes with the temperature differential, which is why thermal solutions are rated in °C/W which leaves that variable ambient open but gives you a formula

as a last note, the supply's total capacity decreases with its temperature
its rated at 25C, and you should likely figure approx a 1\3rd decrease at 40C
 
Open your case ... both sides ... then let run for an hour ... is the air blown by the PSU the same? If cooler ... then your PSU is working perfectly ...
 
Well my case is only 26c and my cpu temp is 40c..accord ahem MBM5.
If I opened my case, of course the temp going drop. Its drop like 4c less on the cpu and 1 or 2 on the case. As for PSU, I should revert what I said b4. Its blown lurk warm air. So, I hope this is normal. Thanks guys for help.
 
If your case temp drops when you pull off the side panel, you don't have a very good airflow setup going. In a well designed system, it's possible for the temp to increase because of the disruption of the flow from bottom front to upper back. May ask around in OC&C about better cooling/airflow techniques?
 
Vertigo Acid said:
If your case temp drops when you pull off the side panel, you don't have a very good airflow setup going. In a well designed system, it's possible for the temp to increase because of the disruption of the flow from bottom front to upper back. May ask around in OC&C about better cooling/airflow techniques?


I have to agree here as my case temp actually increases by 3c when I have the side off. I have an Antec 3700AMB w/cutout fan grills and 2x120mm fans moving ~78cfm each.

Post some pics, you'll get all kinds of comments then. A lot of factors contribute to good/poor airflow and posting pics of your case setup would allow people to contribute directed suggestions instead of blind ones.
 
Okay let me brake down my specs. The case is Lian-Li pc-60, AMD Barton 2500(no o/c yet), Raedon 9700 XT, 1gig DDRAM, and yes RAID 5(40gig x 5). Im using those 4 stock fans, except the blow hole, that one im using Antec 35cfm fan. I was wondering, if those 2 intake fan is good enuf? I was thinking to change the exhaust fan to TT smart fan 2(70 cfm :) ). Oh all my floppy and hd cables is rounded type. I gave out those flat ide cables.
I think any case, if you open up the side panel the temp will going drop for sure.
 
If your PSU is blowing lukewarm air, I'd venture to say there's nothing wrong with that.

I had to build a comp for my girlfriend a while ago. The case had NO places for fans (other than the usual 120mm in back), and all I could do was a DIY 80mm mount in the bottom front. The whole setup runs relatively warm, and the PSU exhaust is pretty warm, but it's perfectly stable and safe.

Oddly enough, the junk PSU that was initially in it got a broken fan. Since it was junk and only had 1 fan in the first place, it managed to overheat and burn itself out. Had to replace it, but the new one has been fine since then, lukewarm air and all.
 
At least if the air is only lukewarm, then you won't need a BTU rating on the side like some machines should.
 
its a thermally controled fan that runs as slow as possible to avoid any extra noise, its normal.

for this reason i'm getting rid of mine,i just ordered two new PSUs less than 3 minutes ago :)
 
Wooweee, can I speed up the fan speed, I dont mind a couple of db's. :)
thanks alot for the tips.
 
If you bust everything apart, you'll find that the fans are hooked up separately inside from the regular +12v line. So, if you soldered them into the main +12v line (not the fan only), the fans would run at full speed.
 
Back
Top