advice please on memory for new system?

rifter

Limp Gawd
Joined
Apr 24, 2005
Messages
166
specs:
3200+ venice
dfi LANPARTY UT nF4 Ultra-D
x800xt
36gb raptor
still deciding on psu (any advice would be good)
dvd burner, floppy
hsf (still trying to decide-would like something quiet)

i am only a mild overclocker, but this could change :D

thanx
 
Got memory? TwinMOS SP is nice for that setup if you don't have any yet.

74GB Raptor is substantially improved from the earlier version.

Power supplies.

Mild for a Venice is about 2.7GHz.
 
i already have the raptor, may move to the 74 in the future, but for now the 36 will do, just received the x800xt today as well as the 2005fpw. have not ordered the cpu or mb, but those are definitely the ones i am getting. i checked that dfi street page earlier today, but still was a little clueless about the the psu. thought about getting the fortron blue storm, or the enermax eg565ax-fma (think that is the model).

mainly just need to select memory so i can get the rest ofmy order on and get this thing built.
 
Type TMSP into the search box on Newegg & get two of the 512MB sticks.

Fortron and Enermax are both good.
 
ashmedai said:
Type TMSP into the search box on Newegg & get two of the 512MB sticks.

Fortron and Enermax are both good.

is that ram any good? I might buy it since its only 100 bucks for a gig
 
you should get high voltage ram for the lanparty.. either the twinmosSP or if you have the money, ocz VX ;) (if you want to overclock)
 
The search term I gave you should pull up TwinMOS SP which is perfect for that board...once you get it flash with the 5/10-2 BIOS & put it in slots 1&3. It takes about 3.2V give or take and'll most likely do over 250MHz at 2-2-2.
 
the twinmos from the search term at newegg shows a cas of 2.5, is that correct? also, it will still run dual channel if i buy two correct, even though it is not in a kit right?

remember i am only a mild overclocker, and i have never messed with voltages before, i am a real noob when it comes to oc'ing. kind of wary of my own skills :eek:

ashmedai: you seem to have a similar setup to what mine will be. do you have a personal guide you could pass along that might make my initial setup easier when i get all the gear? also, what kind of cooling are you using on the cpu, case you are using, etc. i need to choose a hsf still, and wondering what you are using to achieve that excellent oc?
 
ashmedai said:
The search term I gave you should pull up TwinMOS SP which is perfect for that board...once you get it flash with the 5/10-2 BIOS & put it in slots 1&3. It takes about 3.2V give or take and'll most likely do over 250MHz at 2-2-2.

What about me :p
 
looking for some more advise. anyone anyone

is the ocz vx ram really that much better than the twinmos talked about in this thread? it is at least $100 more per gig. is it worth the $100?

thanx
 
Gold VX and TwinMOS SP/400 both use Winbond CH-5 chips, so fundamentally they're identical.

Gold VX is priced higher because OCZ can, because it's pretested at PC4000 (250MHz is well in range of almost all non-defective CH-5 modules), and largely because the market has left people used to paying that much for "good" memory.

I also have a bit of a peeve here. Buying pre-binned PC4000 and running it at 250MHz isn't overclocking, it's running it at stock. Researching available parts and finding some PC3200 with good odds of being able to run at a higher than rated clock rate is overclocking.

Anyway, my personal recommendation if you're leaning towards Gold VX is to buy 4 sticks of TwinMOS SP 400 instead, test them yourself, and keep the best two. You've got the same odds buying Gold VX as you do TMSP/400 of getting a "good" vs "bad" stick (higher vs. lower abilities), so if you're determined to spend $200 on memory, take the best 2 of 4 and you'll get more for the money.
 
I am australian and there are only 2 stores selling twinmos 512mb 184 Pin DDR400 ram. However, these stores are selling this =
LEGEND / TWINMOS OEM 512Mb 184Pin PC3200 DDR400

Is it the same stuff or different? What is the LEGEND part?
 
since the chips have to run at such voltages, how are you keeping them cool? did you add heatspreaders and a fan?
 
heatspreaders make things hotter. just put a small fan on em. i personally use a tweaked pci slot blower for when i give my ram a bit of voltage :D

BNC: i don't think that's twinmosSP :(
 
eclipse, how do you have the slot blower configured? i have a spare one that i can use, how do you have it mounted

thanx
 
also, if i am not much of an overclocker and have no real experience with tweaking memory and especially ram voltages would you guys still recommend the twinmos? what is it rated to run at stock? i know newegg lists the cas as 2.3, but what about other timings?

i am new to this so any good guides about tweaking these settings as well as cpu/fsb you could point me to?

not try to fry anything right off the bat :eek: with new gear
 
rifter said:
eclipse, how do you have the slot blower configured? i have a spare one that i can use, how do you have it mounted
just took off the metal part that holds it in place, taped two toothpicks to it's sides to hold it upright, then placed it ontop of my ram. my case is always laying on it's side though ;)

and you mean cas2.5
for initial testing, i'd run it at stock for a while and do lots of testing to make sure you didn't get a defective part. then slowly increase the voltage. i'd personally stop around 3.2v for 24/7 if you have a fan on it :D
 
http://www.monarchcomputer.com/Merc...duct_Code=140713&Category_Code=Unbuffered_OCZ

im thinking about buying those tomorrow

gonna put them in with my Venice 3200 and Epox 9nda3+

right now with my kingston ram i can do 2.7 ghz but at a divider of 100 on my mobo and that puts my ram at 145 mhz frequency. If i do a divider of 133 it wont boot at all OC'd

So that leads me to believe my ram is either A. a crappy overclocker or B. defective.

I plan on running memtest86 on it and if it is defective rma and then get a gig still. Put the 512 rma in a hptc box if thats the case.
 
Back
Top