Abit IC7-G : no video

Mr_D

n00b
Joined
Dec 26, 2004
Messages
30
I just got my new motherboard, a shiny new IC7-G, but alas once a transplanted all my old parts onto it, and put in my new ram, no go =[

The machine turns on and my cdrom drives light up, but I get no video. I have checked the connection from videocard to the monitor, but it is fine. The video card worked great in my old machine.

My old system:

------------------------------------------------------
System Information
------------------------------------------------------
Operating System...
Windows XP (5.1.2600) Service Pack 1

CPU Model...
[1] Genuine Intel (2386 Mhz)
Core Speed: 2386.5 MHz
Multiplier: x 18.0
FSB: 132.6 MHz
Bus Speed: 530.3 MHz

Mainboard...
Intel Corperation
Model: D850EMV2
Chipset: Intel i850E Rev.A3

Memory in Megabytes...
511.3 Total Physical Memory
303.23 Available Physical Memory
1945.13 Total Virtual Memory
1706.81 Available Virtual Memory
Channels# : Dual
Frequency: 397.8 MHz
FSBRAM : 4:3
tRDRAM: 10 clocks
tRCD: 7 clocks

Display Resolution...
1152x864 (32 bits per pixel) @ 60 hertz

------------------------------------------------------
System Drives
------------------------------------------------------
JLMS DVD-ROM LTD-166S
TDK CDRW5200B
WDC WD800JB-00CRA1
Generic DVD-ROM SCSI CdRom Device

------------------------------------------------------
System Hardware
------------------------------------------------------
Display...
ProviderName NVIDIA
DriverDate 7-15-2004
DriverVersion 6.1.7.7
DriverDesc NVIDIA GeForce FX 5500

Media...
ProviderName Creative
DriverDate 6-23-2004
DriverVersion 5.12.1.444
DriverDesc Creative Audigy Audio Processor (WDM)
ProviderName Creative
DriverDate 1-29-2003
DriverVersion 1.0.0.0
DriverDesc Creative Game Port
ProviderName Microsoft
DriverDate 7-1-2001
DriverVersion 5.1.2535.0
DriverDesc Intel(r) 82801BA/BAM AC'97 Audio Controller

I just upgraded the motherboard to the IC7-G and this RAM: http://www.newegg.com/app/viewProductDesc.asp?description=20-145-440&depa=0

Help =[
 
Did you double check all your components to make sure you installed them correctly? For instance, check that the heatsink is properly seated. Did you put some thermal compound on the processor before putting it back in the socket? Take the video card out and firmly seat it back in its slot, do the same for the memory. Use one stick of memory at a time and see if it posts with a smaller amount of RAM.
 
Based on your answer, I would go out on a limb and assume it isn't POSTing.

Re-seat your CPU. The Abit IC7-G has been known to have a stiff ZIF socket. Press down on the CPU while clamping it down.

A successful POST in one short beep within about 5 - 8 seconds after pushing the start button.
 
Tried reseating CPU, Video Card, RAM, less RAM, Using an old PCI video Card.

Nothing. It doesnt post. The CDrom drive light stays on and it will not open by pushing the button. The DVD drive will not open either.
 
attempt to boot it outside the case, just to check for shorting and stuff

The IC7 line has always given me a lot of problems with POSTing. I can open it to reseat RAM, and the thing decides it doesn't want to post any more. :confused: :(
 
If you get nothing, no beeps at all, then you have a problem with either the CPU. mobo, or BIOS. I doubt you have a bad CPU or mobo. I can't say whether or not you have a bad BIOS. That would depend on whether or not you have recently attempted to flash it. That leaves your construction as the most likely culprit, which is why I suggested for you to re-seat your CPU. But, if you are certain that that is fine, then good luck. That's all I have.
 
:\

I have a friend coming over friday to help. Im going attempt to reconstruct my old computer.
 
Now my old computer has the same problem -_-

It CAN open and close its cd rom drives though. Other than that its like the same thing =[
 
Did you ground yourself while doing all this. You may have shorted out a component, but this is simply a guess.
 
Well, the floor is wood, and I always touch the case before touching anything else (which is what I am told should work). I hope I didnt screw it up =[
 
I've built systems on carpet so I don't think it was that (the computer was not on carpet just me walking on it but I had one of those wrist strap things). I think it would be hard to short something on a wood floor, plus you took the proper precautionary measures.
 
turns out the pins on the bottom of the cpu got bent and it shorted out.

I took out my frustrations on the CPU with my dremel, and now have a 2.4ghz keychain. -_-;;

I guess ill buy the 2.4c since its a nice price for the excellent proc with how I can OC it :\
 
Back
Top