a8n-sli 1T command

q-tip

n00b
Joined
Feb 6, 2005
Messages
5
hi,

i got a8n-sli deluxe with a 3500+ newcastle proc with 1gb of XMS Corsair
4x256mb pc4000 ddr500 my settings are

ldt 4x
dram config 400ddr 2.8V
cpu 200x11
mem settings 8 4 4 3
rest is default
bios 1004.001
video asus Extreem en6600gt top

now when i set my command rate at 1T my pc reboots beebs and just stops
no screen no nothing just beeps and then i have to reset my bios before it starts up again.

Does anybody else have this problem or aim i overlooking something
any suggestions are welkom

a verry big thanks for helping!!!!
 
1T command rate is very hard on the memory when you try to push it. You can try increasing the VDDR, but from my experience and information I've read elsewhere, if you have more than 256MB of RAM, pushing the FSB high enough will require you to relax the command rate to 2T. I think that's why you're getting BIOS error, memory controller is having a hard time running your RAM at specified speed together with 1T.
 
You're running 4 sticks of memory if I'm not mistaken. When running in this configuration timings become more of an issue (AND recommend DDR333 rather than DDR400) - hence your problems with command rate. Try expreimenting by removing two of the sticks of memory and seeing if your system responds more favourably:)


Thanx,
D
 
So i cant run 1T with 4sticks????

and if i pull 2sticks would this compensate running at 1T instead of the
4 sticks of memory or would it make ni difference at all???

or do i have to buy 2 sticks of 512mb with LL or C2


THANKS!!!
 
Im pretty sure you can use all sticks, but you HAVE to be at ddr333 if you want a 1T command rate. And its like this on ALL Nforce4 and 3 motherboards, so dont feel bad. What i did to get around this was i used 2X512 meg sticks and im at 245 fsb with a 1:1 ratio at 1T(ddr490), and im getting like 7,200 mb/s bandwith. My timmings are 2.5-3-3-7. If i were you, id go to 333 and overclock it till the cows come home. You can do anything you want really, but i know as a fact that if your running 4 sticks, you HAVE to put it at ddr333 if you want a 1T command rate. So, put it at 333 and bring the fsb up like 55 or so and youll be at ddr 440ish at a 1T command rate. But remember that right now ALL A8N-SLI boards have a fsb limit of about 240-250, after that it becomes unstable. A bios fix should be along to fix it shortly. In the beginning, no one could go past 210, then it was 220, now its 245. So things are getting better. Im at 245 and im stable as a rock.
 
3500+ winchester
2x512 mushkin 3200 2-2-2 v2
A8n SLi

1T mode on, Cas 2.5, 225 fsb x 10.5

1.7 v for memory
1.5 v for cpu

works for me, runs 3dmark etc stable .. at 230 fsb 3dmark locks up with the 1t command on

just tried 11x 225 still seems stable 2475 mhz @ cas 2.5 and 1t
 
hi, thanks for the response

i am running now 2640mhz 240x11
mem settings 3 4 4 7 2.75V ddr400

everestscore: 6642
prime95:eek:k about30min
superpi:34sec 1mb
sisasoft cpu arth: alu 12021mips
:fpu 4132
:isse 5350 mips
cpu mul:24959 it/s
:26846 it/s
band :5806 mb/s
: 5812 mb/s

Is this a good score ore should i milk the cow again or waite on the bios update


THANKS!!!!!
 
Back
Top