800d rebuild

Loafdogg420

Limp Gawd
Joined
Jun 2, 2010
Messages
445
What's up people? I recently picked up some new hardware and found that I could use that as an excuse to rip my system apart. :D

Really though, the reason I did it was because I felt like the 800d, in its stock config, wasnt moving air as efficiently as it could. I originally just threw some good noctua and noiseblocker fans in but wasn't happy yet. So, I gutted her. I've been building systems for a while but this is my first "real" case mod.

Tell me what you think.

P.S. New camera.. not used to it yet. Might be some blurred shots here and there. ;)


Here's how it started: 5970 and i7 920 w/ 140mm in the bottom.
before.jpg


Cleaned out and ready for surgery.
DSC00063.jpg


Mobo and new 6 core sexiness.
DSC00060.jpg


Chaos in my office!
thebeginning.jpg


Drive bays and metal divider removed. Time to practice the dremel skills.
DSC00077.jpg


Quick connect discs ftw
DSC00086.jpg


Most of the crap cut out of the front.
DSC00084.jpg


Decent cuts.. sanding, sanding...
DSC00083.jpg


Fitting the plexi for the new divider.
DSC00081.jpg


I decided to paint the interior of the case a nice "hammered" white.
DSC00108.jpg


Not too bad... You can see one of the pieces hanging in the background there.
DSC00109.jpg


Skipping ahead a little bit. I cut out the front, top portion of the case including the front panel, made up some moldings for the cut edges and was experimenting with ways to mount the reservoir. I spent a week trying to decide how to redesign the front panel. I ended up using a sheet of patterned aluminum from home depot. It was easy to cut and mount and it looks half-decent, i think. Most importantly, its almost wide open for air. I will add some filters later, most likely.
DSC00102.jpg


The outside I did a civic type r-ish metallic blue. Has some nice bling to it :D
Metallicblue.jpg


I recently moved to Wisconsin for work so, in the spirit of... cold.. i guess lol, I "frosted" the reservoir with the same hammered white for a chilly effect.
frontpanelbeforehardware.jpg


Close-up of the res.
frostyreservoir.jpg


Test-fitting the rads and replacing the rubber grommets for the cable management.
DSC00152.jpg


With the side panel :) Ready for hardware!
DSC00155.jpg


The 240mm radiator and wd blacks. I salvaged the lower HD cage and turned it so its more 650 style. This shot is from when I was leak testing, you can see the drain port that hasnt been installed yet :p
rightinnerhdchassisand240radiator.jpg


With all the goodies inside. The coolant is feser 1 clear, but its UV blue. I have some light on order that should make it POP
leftsidemobocase.jpg


One of the bitspower rotary fittings i added. Made it real easy to get behind the mobo and around the fan.
Topleftmobobitspowerrotaryfitting.jpg


Expansion slots. Top to bottom. HIS 6950 with 6970 shaders/clocks w/ EK block. Revodrive x2, x-fi. If this card overclocks like a madman, i'm going to pick up a second and move my x-fi to the top 1x slot, above the primary gpu. Another bitspower fitting. so sexy.
DSC00171.jpg


The tygon 3603 makes is real easy to make tight, short jumps between blocks. The exterior blue ended up matching the blues of the ram and mobo perfectly.
DSC00169.jpg


The overall build was super clean, even with the TX corsair PSU. If i had the modular variety, daaamn. I may very well grab an hx1000 or the 1.2kw newness if I add another vid or two :p
outsidecasewithpanelon-1.jpg


And there we have it. Spent about 25 hours on the whole thing. I was in a relaxed work mode for the most part :p
outsidecasewithpanelonzoomedout-1.jpg


I couldnt be happier with the temps at the moment. Seeing 23-30 C accross the cores on idle and nothing higher than 60-61 on full load at 4.32 in IBT and p95. The video card seems to be nice and cold, idling around 25 and 40 or so full load. Havent done extensive testing yet. I definitely have headway for additional overclocking with the addition of the new rad. I'll add some new pics when I get it lit up. Please leave some comment! Thanks for viewing!
 
Back
Top