7900gt Volt mod not going so well.

Dethred

2[H]4U
Joined
Jul 30, 2006
Messages
2,543
Hey guys,

I am new here but have been lurking for months.

I got my EVGA 7900GT (256-P2-N583-AR) and Zalman VF900cu last night and volt modded it to 1.5v. I waited a few hours for the conductive ink to settle and cure and then threw in the card and immediately was able to overclock it to 650/1660. After a few benchmarks etc I came up with poor results.

3dmark05' gave me a max of 9670. That isn't too bad but from what I have read most people have been getting 10k+. I know benchmarks don't matter that much but it is indicating to me there is a bottleneck or something isn't right.

So... I overclocked it to 660 and tested for artifacts... after a few seconds ATitool found delta artifacts (or what ever it says at the bottom). Now at 650mhz it also gets artifacts. Temps never exceed 61*C in the artifact scan. I have heard of others getting 650 stable with only 1.4v. What could I be doing wrong?

Thanks!
 
Not all cards are the same... some do better than others (even same model). I would be VERY careful about volt modding. It is a very risky thing and you may have already toasted your gpu.
 
It does fine at 600 core... I am wondering if one of the lines isn't getting me a full 1.5v
 
I can only play at 645 on my cards at 1.4v... I have them down to 635 for 24/7 use... it's just hit and miss with these 7900GTs.. some do better with less vcore than others.
 
Ive got a xfx 7900gt that ive volt modded to 1.5v with a vf900. Im running 680/900 as my clocks, i did the pencil vmem mod as well as the vcore. It helps to get your memory clock as high as possible, then bring the core speed up. Besides that, processor may be slowing you down. I have a opteron 165 @ 2925MHz, and i score 11,300 in 3dmark.

Oh, and my temps max out at 50* load after 2 hours...maybe try reapplying as5
 
Dethred said:
Hey guys,

I am new here but have been lurking for months.

I got my EVGA 7900GT (256-P2-N583-AR) and Zalman VF900cu last night and volt modded it to 1.5v. I waited a few hours for the conductive ink to settle and cure and then threw in the card and immediately was able to overclock it to 650/1660. After a few benchmarks etc I came up with poor results.

3dmark05' gave me a max of 9670. That isn't too bad but from what I have read most people have been getting 10k+. I know benchmarks don't matter that much but it is indicating to me there is a bottleneck or something isn't right.

So... I overclocked it to 660 and tested for artifacts... after a few seconds ATitool found delta artifacts (or what ever it says at the bottom). Now at 650mhz it also gets artifacts. Temps never exceed 61*C in the artifact scan. I have heard of others getting 650 stable with only 1.4v. What could I be doing wrong?

Thanks!
Sounds like you're in the right range; maybe slightly towards the bottom end but still about right. As always no OC is guaranteed. Have you measured your voltages with a voltmeter? Also what is your cpu? If you're on say a 3200+ that's going to compromise your scores a bit
 
I also got a evga 7900gt ko 256-P2-N564-AX on a vf900 and currently running 710/1660. I think I did a 1.55 and just scrapped a couples lines on the mem. I benched around your score but I think I'm cpu limited.
 
Well... I'm pushing 1.5v ... I tried 1.55 and the score increased by 5mhz and my memory went up 20mhz (strange).

One question... I changed to the older 83.90 drivers and the temps on my VF900 seem to have gone from mid-40's to 58C both temps with 1.5v. Now it loads at 75*C.... which doesn't seem right. My case is in the mid 80*F range so is it just too hot in my room for this to be pushed that far?
 
Peter949 said:
I also got a evga 7900gt ko 256-P2-N564-AX on a vf900 and currently running 710/1660. I think I did a 1.55 and just scrapped a couples lines on the mem. I benched around your score but I think I'm cpu limited.

I have my 3500+ venice at 2.475 right now because its unstable in this heat. I was running 2.6ghz for my benchmark and was able to hit 10010 in 05 and 5051 in 06'
 
Just ran 05 and scored 11141 @ 715/1682. If heat is a issue for your cpu, I would recommend a aftermarket heatsink. 1.55v is a lot without proper cooling. I'm personally on a Big Typhoon, but something cheap like a Arctic Freezer 64 would do wonders. Have you tried erasing the the written circuits and doing again to make sure that it was complete circuits? What did you expect to gain? I personally think you won't get much more then 700ish.
 
well my idle temps for the 7900gt are 58*C-60*C and load hits 75... Is this right for a vf900?
 
Dethred said:
well my idle temps for the 7900gt are 58*C-60*C and load hits 75... Is this right for a vf900?

Regarding the temps, I was talking about your cpu. I idle low 50s w/ my vf900 and load I think but haven't checked around mid 60s
 
Yeah after seeing that you have a 3500+ at 2.9 I am going to get another cooler. I think something must be wrong with my volt mod.
 
Dethred said:
Yeah after seeing that you have a 3500+ at 2.9 I am going to get another cooler. I think something must be wrong with my volt mod.

My cpu is a manchester core and not a venice. Ya, I recommend you clean off the circuit on your card and redraw them and take your time.
 
Dethred said:
well my idle temps for the 7900gt are 58*C-60*C and load hits 75... Is this right for a vf900?

With a CU700 and 1.45 @ 675/1800 My card idles at 41c and loads at 53c. Your temps sound high.
 
Spazilton said:
With a CU700 and 1.45 @ 675/1800 My card idles at 41c and loads at 53c. Your temps sound high.


Cpu and gpu temps are a lil high. Could be air flow problems.
 
well its definitely not airflow problems. I have two 80mm front fans, a 120mm rear, an 80mm top and 80mm side. I guess I might have to reapply thermal paste and redo the volt mod today...
 
I modded straight to 1.45

I have a NV Silencer, and my temps tend to load around 55ish (if it's a non-heatwave day).

I can get 680 / 1800, it seems i can get more, but I don't really care for more, I feel blessed with such a great oc'er.

:)

Your millage may vary.
 
well i changed from the 83.90 drivers to the 91.33 and my Idle/load is now: 44*C Idle and 61*C under load. WTF??? Still no better overclock. :mad:
 
I highly doubt drivers will have any to do w/ the oc or temps. So did you redo the mod?
 
Going to redo the mod in a few minutes. I tried going back to the new driver after I suspected that the temps had changed when i went back to the 83.90. Temps dropped about 10*C across the board. Whether its a real temp drop or the older drivers were just giving false readings, the temp inside my case is still the same as before and its definitely 10-15* cooler now.
 
Well i did the mod over again, and after a few hours of letting it cure I can only get 600 core at 1.55v
 
Dethred said:
Well i did the mod over again, and after a few hours of letting it cure I can only get 600 core at 1.55v


Are you serious? You have a worser overclock w/ more volts? Wow, can you take a picture of your mod. You are doing something wrong or that card is just a dude. Oh, try this. Leave memory stock and try to find the core oc only first. Hmm....how many watts is your aspire psu?
 
Peter949 said:
Are you serious? You have a worser overclock w/ more volts? Wow, can you take a picture of your mod. You are doing something wrong or that card is just a dude. Oh, try this. Leave memory stock and try to find the core oc only first. Hmm....how many watts is your aspire psu?


Seems that way. My PSU is a rosewill 450watt 34A Dual 12v. I've already tried the memory thing. I might be able to get a pic this weekend. One question, how much do you use, and should you cover up the connection points or just make it touch it? I covered mine in ink, and used quite a bit between the connections, though it is pretty well done (at least compared to others I have seen) and none of the ink touches any other contact points.
 
Dethred said:
Seems that way. My PSU is a rosewill 450watt 34A Dual 12v. I've already tried the memory thing. I might be able to get a pic this weekend. One question, how much do you use, and should you cover up the connection points or just make it touch it? I covered mine in ink, and used quite a bit between the connections, though it is pretty well done (at least compared to others I have seen) and none of the ink touches any other contact points.


Do you have a better brand psu to test on hand? 500watt+ is preferred. I personally used scotch tape to draw the lines and peeled it off to make it neat and clean. I didn't cover the pointed but just meet it. I don't know how good/reliable is your psu but rosewill is a generic brand. Well, I hope you reach at least 700core. Are you modding the mem also? If so make sure you aren't over doing the mem so it artifacts or makes the card unstable.
 
No vmem changes, I am going to pick up a multimeter tomorrow to make sure I am getting the full 1.55v. Where is a safe ground for the black lead?
 
If your stable OC is going down with more vcore, I would be really careful now... you're at 1.55 also, which is beyond the spec of the voltage regs and the gpu core... 1.45 ~ 1.5 is "relatively" safe, but over 1.5v you enter a MUCH higher risk zone, imo. So, test with the multi-meter and see what your actual vcore is.. if it's 1.55, go back to a 1.45v over-volt and be happy with whatever stable OC you can get there. Also cool the card VERY well! Otherwise I think you're running a big risk of burning the card out..
 
revenant said:
If your stable OC is going down with more vcore, I would be really careful now... you're at 1.55 also, which is beyond the spec of the voltage regs and the gpu core... 1.45 ~ 1.5 is "relatively" safe, but over 1.5v you enter a MUCH higher risk zone, imo. So, test with the multi-meter and see what your actual vcore is.. if it's 1.55, go back to a 1.45v over-volt and be happy with whatever stable OC you can get there. Also cool the card VERY well! Otherwise I think you're running a big risk of burning the card out..


Very true. So take he's advice in consideration. All oc is a gamble. I remember that gpu is a 7900gtx gpu which normally gets 1.5v or 1.4v but I rather you have a functioning card then a dead one.
 
I will be reading the voltage tomorrow with a multimeter. The only things that could be out of the ordinary is that I painted the ink on with a toothpick so its pretty thick and stirred up, but all connected. Also, the contact points are covered by the ink. Could the "Reloaded" card have different volt points?
 
Dethred said:
Well... I'm pushing 1.5v ... I tried 1.55 and the score increased by 5mhz and my memory went up 20mhz (strange).

One question... I changed to the older 83.90 drivers and the temps on my VF900 seem to have gone from mid-40's to 58C both temps with 1.5v. Now it loads at 75*C.... which doesn't seem right. My case is in the mid 80*F range so is it just too hot in my room for this to be pushed that far?


with stock volts using vf900Cu and stock speeds 450core i get about 46c idle and 56c load, how with 1.55v i get 51c idle and 70~71c full load. so i guess its pretty normal for those temps. these cards can operate at 85c w/o problems anyway.. i did a temp test on my card and it takes me 92c b4 i get any artifacts at 650mhz core.. 90c is prefectly fine on my overclock.. but id never recommend it running past 80c
 
That doesn't sound right.. both my cores with vf700cu's idle at 1.4v idle at 37c, well, the top one at 38c.. they load in the 50s.. maybe a little higher depending on ambient and intensity of 3d app.. with a vf900 at 1.5v or so.. I would think you'd idle around 42 or so... maybe upwards of 45 if the room is hot. Drivers and bioses have been know to scew temp readings.. the only question is, which reading is the right one? if any? do you have extra fans getting air over the cards? how's your case air flow? You might want to consider a re-mount of the vf900 as those temp readings sound pretty high.. or better case air flow.
 
Dethred said:
I will be reading the voltage tomorrow with a multimeter. The only things that could be out of the ordinary is that I painted the ink on with a toothpick so its pretty thick and stirred up, but all connected. Also, the contact points are covered by the ink. Could the "Reloaded" card have different volt points?


Any opinions on these possible issues? When I redraw the lines should I do it directly from the pen with tape covering stuff, or is it ok to "paint" it on there?
 
Hrm... I painted mine on with a TP also... it should not matter if it's thick.. it's better actually.. lower resistance.. I am not sure about the reloaded cards.. they do automatic vcore adjustments to 1.45v when a 3d app is running, so they might be trying to regulate and over-throw your vmod.. I'd read up on this at XS if I were you..

http://www.xtremesystems.org/forums/showthread.php?t=94177&page=25

this is the end of the HUGE thread on 7900GT vmods.. scan backwards for relavent info.
 
That doesnt make sense though. With 1.45v I should be able to overclock past 530mhz with out the conductive ink. I hit a stable 650 after I first did the mod, and when I inched my way up to 700 it got artifacts and would only run stable at 630 thereafter. Undoing the volt mod and running it off the supposed 1.45v stock settings only will get me about 530mhz core.
 
Ok, I just read on another forum that someone with a DMM tested my exact reload model 583 AR, and it ran at 1.2v even in 3d.
 
yay I tested it and its at 545mhz stable and with the volt mod carefully done its still at 1.2v :eek: I'll post a pic later tonight to check on what the issue might be.
 
Can someone please post the link to the "How-TO" 7900GT voltmod stuff? I wanna give it a shot. What's the stock core voltage at? 1.3? I was going to start @ 1.4 or so.
 
Back
Top