2.5" ide hdd enclosure 64-bit compatibility

tony27310

Weaksauce
Joined
Nov 26, 2007
Messages
114
Hey, i just upgraded my laptop by putting in a faster and higher capacity drive, an i wanted to use my old one to use as a high capacity usb drive. i bout a enclosure and it works perfectly when connected to the laptop i took it out of, but when i connect it up to my desktop it causes the hdd to click, and it doesn't spin. the desktop has x64 xp and the laptop has x86 xp pro, so i think thats whats keeping it from spinning, is there a better enclosure that has drivers that support a 64-bit system? if so a link to it would be much appreciated. here is the enclosure i have now. Galaxy MGB 2500sgcb
 
USB slot isn't giving the hard drive enough power. Could be the enclosure (lousy USB/SATA bridge), or the hard drive, or the laptop mainboard. Try a different USB slot, or a dual-input USB cable.
 
USB slot isn't giving the hard drive enough power. Could be the enclosure (lousy USB/SATA bridge), or the hard drive, or the laptop mainboard. Try a different USB slot, or a dual-input USB cable.

indeed, that happens to me sometimes, i just have to connect the usb cable to the usb connectors in the back panel
 
i tried both, and it came with two cables, but it still gave me the clicking, but maybe ill try both cables in the back, because i did connect them to the front usb ports on the case. its an ide drive btw not a sata drive, but again it could just be the enclosure, ill try it out with the comps i got a work tomorrow and see how it works thanks for the help.
 
If the drive came with two cables (one for USB connectivity, the other for power), or if the drive has one cable that turns into a Y close to one end that splits into 2 USB connectors, then there's a simple solution to the problem:

If it's got two cables, obviously use both, but it depends on whether or not the drive itself (the external casing, etc) has one or two ports. Some but not all 2.5" drives require more power than a single USB port can provide, hence the two cables or a single Y cable. You have to use two USB ports to connect and power the drive.

In my experience, if I plug the drive in using a single cable, I get nada, zip, zilch, nothing at all because one port isn't enough juice. If I plug in both cables, or both ends of the Y cable, and I still get nothing, then here's what I do:

At the moment you plug in the cables/plugs you should feel the drive spin up, that's a given. I've never encountered a drive that didn't do something when it was powered up to some degree. What you're looking for is activity on the drive's LED, that's the important part.

If you feel the drive spin up but you don't see any activity on that LED aside from it's normal power indication (on most enclosures, the LED will be green to indicate power is present, and whenever actual data flow occurs, it'll change to RED during those periods), then there's still hope, so here's what to do:

Plug in the two ends or two cables to the PC itself, but don't plug in the cables to the drive. When you're ready to actually plug in the drive, do it and watch the LED. You should feel the drive spin up, but if you never see any activity on the LED other than power, immediately unplug the cable from the drive (not the PC) and then plug it right back in, just a quick disconnect/reconnect, shouldn't take more than a half-second at best and keep an eye on that LED.

If you did it right, you should see it change color to indicate data activity going on, and if you did it right, at that point you should hear the device connect sound from Windows (the "ba-bump" sound made when you plug in a USB device) and then Windows should detect the drive, etc.

If not, unplug it again and try again. What's happening is similar in principle to a car engine:

It takes more power to get it running than it does to keep it running. The biggest power drain on a hard drive is when it's first turned on because it takes a lot of juice to get the platters spinning at their native rotational speed. Once that's happened, the drive's power requirements drop considerably.

The trick here is to plug it in, get the drive platters rotating, then unplug it while they're still spinning but just for that half-second or so until you plug it right back in - once the platters are in motion, the power tap to keep them spinning isn't as bad the second time around, and since they're already spinning, all you're doing is getting them up to the proper rotational speed. Less power used = more power for the drive circuitry and electronics to function properly, and voila, Windows can see the drive and then it works.

Sounds weird, and I get wordy with my instructions, but it does work as this is my "standard" way to get USB drives, most notably 2.5" externals, to operate, and it's never failed to get the drive up and running with 1 and sometimes 2 connect/disconnect/connect cycles.

Hope this helps...
 
well i didnt read that but the drive actually comes with a y cable like set up but the power can be plugged into either the data cable or the drive enclosure itself, i did get the thing working though, i did the quick plug unplug thing, but it was just luck, because i didnt see the reply until now, thanks for all the help, to bad the computers at work wont let me install the drivers for it to work, bummer right, i guess its just going to be a quick swap hdd for when i reformat and stuff like that. thanks a lot guys.
 
Back
Top