Search results

It's kind of funny you should mention that; I was reading though the thread and had just unconsciously started putting some sort of 'roughly equivalent'-sign between 'fanboy' and 'commie' :p Seriously, what does it matter? If everyone always bought exactly 'the best bang for the buck' (which...

Thanks. It's official, I am part mole. Well, maybe not, because even moles would have been capable of reading the Second Page Of The Same Thread :p So I found the statement and the f3a bios; will try it when I get back to my machine. My BE2350 will currently not go beyond 2.3GHz (220...

Okay, I may be rather thick, but I've read most of the thread now and I still don't understand what bios to use to get the CPU voltage option, and if possible at all, where to get it?

Yeah, I don't know, some things about it are definitely nice, but some aren't, and this humming is just like my Shuttle. Problem solved now, however. I just moved into a bedroom that hums, kind of a low deep hum..(from the heater on the floor below). You can switch the heater off, if you like...

Assembled, now the only mystery left is how to get rid of all the resonance. It's kind of a deep hum that sets my teeth on edge when I'm too close to it, but otherwise reasonanly quiet. If I press on the top plate the hum decreases; and I've tried putting bits of paper for isolation between the...

Hahahahahahahaa indeed. I thought of that last night. Step 18 , 'Mount rails on HDs' is illogical in itself, because they obviously just fall off - but when you slide them into the cage, which is step 19, they just as obviously have no way to go = ) You are the first one to really spell it out...

More elbow grease, haha, yeah, I found that if you push with a flathead screwdriver straight down on the side of the little 'hook' closest to the center of the grille, they open just before you stab yourself in the knee. I'm afraid the HD rails' plugs' or 'bolts' or 'pins' are beyond me though...

Ah, thanks for your reply. I feared I was just showing my lacking practical technical side, but your answers at least partially say the chassis is a bit weirdly built in some ways. In regads to the front fan grille- even with a flat head screwdriver, where exactly do you push..? I can't see me...

Helo. I'm very sorry if these things have been asked before - I looked around but couldn't find their answers , but if they do exist please refer to them. They relate to the assembly of the Sugo SG03. The questions go as follows: First - how do you remove the fan grille on the front? The...

I'm not, especially after having waited for an answer for three working days :p I'll just measure the clearance length in the four directions of the motherboard when I get it; check specs of different <78mm high coolers, then punch the wet newspaper.

Well, I've emailed all possible resellers of the NT06 (none in Ireland,a few in Sweden) - none of them had the AM2 compatible version. One of them had the NT05 - but again, not the AM2-version. The potential alternatives I've been able to scrounge up so far are two Zalmans: Zalman CNPS7500 and...

D-Three: Should perhaps have said 'Ireland', land of 2.5 computer webshops. Thanks for the advice however. Has anyone attempted any GPU coolers of average to ..(long? High?) height in the SG03?

Helliya. Bet you thought the OP would be sketchy and hard to follow after having tried to read that title eh? :) I was planning on building a matx-machine with an AMD X2 BE-2350, an X1950pro(with no cooling yet) and one of the following boards: abit An-M2, or Gigabyte GA-MA69GM-S2H...

An undead horse goes- ..ah, but this is no horse, this is a good thread :) I thought I'd use it to ask a few questions regarding my planned Sg03 build. Firstly, I have an X1950pro with the worst stock cooling ever, so I'm wondering what kind of clearance is available for VGA cooling (with...