Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.
I still haven't gotten anything back from Abit, are you sure I was supposed to reply to the e-mail they sent me?
Could I go ahead and fill out another RMA, or will they yell at me for doing 2?
also, when I booted it up and ran the activation wiz, It said my product key has been activiated too much. I had to freaking call microsoft and speak to this middle-eastern dude that I could barely understand...
I hope I don't have to do that again when I get my mobo back :(
Also on a...
ok I repair-installed XP and I'm on this computer right now ;)
So my hard drive wasn't wrecked.
Just my motherboard so far, possibly the CPU but probably not, possible the ram but hopefully not.
This older mobo takes pc133 regular SDRAM my new mobo took DDR ram, so I can't test to see...
Well the serial number I found said it was an invalid serial number, so I had to check off "missing serial number".
I can't fill out the RMA again I don't think?
Also not from NYC, from central new york state here :P
also I looked up this older motheboard, it appears it doesn't support my processor because it's a "barton" and not a "throughbred"
SO HOPEFULLY when I get a new motherboard back from ABIT if I DO, my old CPU and hopefully RAM and everything else works.
If it's just the mobo that friend no...
I set the DVD-RW/CD-RW to boot up first and I selected the XP partition and set it to repair. It's apparantly repairing now in windows setup with 37 minutes left which sucks because I really have to go to the dentist soon.
I also replied to the e-mail with "yes I accept and confirm" and still...
MBR?
Also I do not have a floppy drive, one in my old case failed was hoping this new case came with one but it didn't (lol).
Pressing F8 I can access the safe mode selection screen.
I press safe mode then windows XP, it then processes all the drivers, when it gets to MUP.sys it freezes...
well I hooked in a new mobo.
Seems my CPU and HDD are dead.
MAYBE NOT but when I hook the Athlon XP 2800+ CPU in the older motherboard which, it incorrectly reports the meghertz and says unknown CPU. This means I think either the CPU is dead or the CPU MAY BE if I'm lucky too new for the...
welp.
Hooked MOBO back up with spacers this time. Unplugged everything from motherboard except the 2 power connectors from PSU, CPU, and power switch wire.
Plug it in, and the red light turns on on my mobo to show it's receiving power. Press power button, and nothing happens...
I do have an old motherboard I used before this one, with regular non DDR sdram and a duron 1.2 ghz CPU.
Most definetly not enough to run any of my high demanding games or anything before I can get a new motherboard.
Yep, looks like I used no spacers. shit.
I was so excited to get this case, get it working, I forgot the spacers. I didn't even think about installing them because my old case already had spacers in it and I didn't have to install them, so I forgot to install it with this new case...
CRAP I see now yes the brass things are SPACERS, and I didn't use them. And now I think I see some damage near one of the screw holes on the bottom of my motherboard, it's really small but there's a red colored mark. (my motherboard is a dark red color).
crap I had an extra PSU and PSUs...
I got that pic off of google, my fans have no MOBO connector only molex, just using it for an example.
So I can hook another fan up to the female for I don't have to reach another PSU wire far?
Also someone else on another forum mentioned to me about using spacers with the motherboard. I...
the only "damage" I can find is I took my copper heatsink off my CPU, and on the cpu (not the di) there is a liquid/gel that has the texture of liquid glue when it's almost dry. No I'm not talking about the thermal paste you put to make heat go through, there is a clear "glue" or something on...
anyway, browsing the net I think I found the female molex is for hooking to my MOtherboard on a connector and male is to go to the PSU.
but I never hooked any molexes to my motherboard, just the PSU.