• Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
    Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.

Recent content by L.o.D.

  1. L

    Best & fast methods to clean WC loop

    Ok, CLR seems to work pretty good for the tubing. I just did a swish/flush on the tubes alone which did help. If I had a couple corks, I would have sealed some CLR inside the tubes for like an hour or so. Right now, I just need to get the foam out of the system. Also, since Petra's out of UV...
  2. L

    Best & fast methods to clean WC loop

    I'm using a Swiftech pump. Is there one in them? I had planned on taking the block apart to check it.
  3. L

    Best & fast methods to clean WC loop

    Bill, I called it a film due to it being really thin like & see through. Looking at the bottle of CLR, it has a list of "do not use on" & copper is one of them. So I guess I would just use it on the Tygon instead and the rad & res.
  4. L

    Best & fast methods to clean WC loop

    What about CLR?
  5. L

    Best & fast methods to clean WC loop

    Can we get back to my questions instead of bickering back & forth please?
  6. L

    Best & fast methods to clean WC loop

    That's why I would flush it with distilled after. Get rid of left over CLR.
  7. L

    Best & fast methods to clean WC loop

    What do you guys think about flushing (not soaking in) with CLR? It's supposed to be safe on copper on rubber.
  8. L

    Best & fast methods to clean WC loop

    Another thing, the coolant is normally blue but it's clear as day now. Last time I took it apart, I stuck my finger inside the tubes at the end & could feel the film. Never took the pump apart before.
  9. L

    Best & fast methods to clean WC loop

    For the tubing, if I could remember which ones I got, I would just order new tubing from Petra's as they are really cheap there. I think I am using 1/2in. ID (3/4in. OD) Tygon.
  10. L

    Best & fast methods to clean WC loop

    I am in need of cleaning my WC loop & would like to know what are the best & fast ways of doing so? I know people suggest to let parts soak in a vinegar mix for hours, but since the mix is just sitting there, there must be a faster way of cleaning them? What about boiling vinegar &...
  11. L

    http://hardforum.com/showpost.php?p=1034875999&postcount=27 Can you tell me what ram & mobo was...

    http://hardforum.com/showpost.php?p=1034875999&postcount=27 Can you tell me what ram & mobo was used for that in the post above? Not sure why Bill closed that thread
    • L.o.D.
    • Profile post
  12. L

    Can't overclock Q6600!

    What mobo & RAM was used to achieve that?
  13. L

    Q6600 Overclock

    tried the NB voltages with various FSB termination voltages. No luck with the FSB at 410. I didn't go too high with the NB voltages, just went up a few steps. Also lowered the RAM timings. Just blue screened with stop error 0x00000124 each time.
  14. L

    Q6600 Overclock

    Hydro, I can get it to 3GHz without touching the ratio. Just set the FSB to 333 & that's it. My RAM voltage is at 2v. PC2-6400 DDR2-800 Crucial Ballistix Tracer 4GBs. 3.6GHz is stable right now. What is MCH again?
  15. L

    Q6600 Overclock

    Actually, the memory timings are at default which I think are what they are supposed to be at. 5-5-5-18 2T I have never messed with the timings other than setting to the recommended from the manufacturer, but the mobo did it for me. EDIT: Ok, I was wrong. It doesn't continue to load, but...
See more
Back
Top