Problem With AMD A88X RAID

YBLEGAL

n00b
Joined
Nov 23, 2013
Messages
4
Just picked up this board, Gigabyte F2A88X-D3H rev.3, building server out of desktop class hardware. Using A10-6800K processor, Corsair 1866mhz memory.

Problem: Cannot use RAID with WD2500 (WD Caviar SE [from 2004]). I have 4 I wish to use.

It doesn't matter if I have them assigned to an active array or not, as long as they are operating under the RAID bios, I have issues. Using them as SATA IDE, they are fine! Every time the RAID driver loads, the discs start turning off, and on, and off, and on, and so on, never being detected by the OS. I can see them in the RAID bios just fine, I can even create an array and initialize them. However, when trying to install Windows 7, or 8, or 8.1, or Server 2012 (my target OS), it just starts power cycling the drives as soon as I load the driver. I successfully installed Server 2012 on a single 80GB WD Velociraptor drive, with none of the WD2500's connected, operating under the RAID bios, with no issues. After that, I tried creating the array of WD2500's, but as soon as the OS attempts to load the driver during the boot process, the drives start power cycling again, and the OS never proceeds to load.

I've updated my bios to F2 (latest at this time). No help.

Why are just these drives power cycling when trying to load the RAID driver? They work fine as single drives not running under the RAID bios. They worked fine in a RAID0 array in my last server (Tyan board, Sil Img controller)...

Ran WDTLER, enabled TLER on one of the WD2500s. Had no effect.

Connected 2 Rosewill RC-216 RAID controllers to same mobo/system. They run J-Micron controllers. Created 2 separate RAID1 arrays with WD2500s. They work fine, and don't exhibit the power cycling. Seems issue is with AMD RAID chipset | bios | driver. Any work arounds? Any Ideas?

Help?!
 
AMD boards use Promise controllers, you are attempting to use a 10 year old drives on a new chipset.
Possible they are simply not recognized and thus are not doing what you want from them.
I installed two WD VR drives in the previous board in raid 1 without any issue, it just needs to be set up first in the ROM before you load your OS.
Unlike Intel trying to create a raid array after OS installation does not appear to be as straight forward if at all possible.
 
You have to set up the OS in RAID as you're installing.
Use the RAID x86 drivers.
You don't have to have the array set up..just your OS disk.
After install you can set up array.
 
I'm trying to use x64 OS's, so you mean x64 drivers, eh?

The driver that's been working for all drives, except the Caviar SEs, have been rcraid "AMD-RAID Controller [storport]". Is this a Promise controller? Chipset is A88X.

I set the array up in the RAID bios during boot. I also tried adding a 5th drive, leaving the Caviar SE's out of any RAID arrays, but attached to the RAID controller. The 5th drive was a single WD VR 80GB. When setup asked for the driver, and I tried to load it, the 4 Caviar SE drives did the same power cycle behavior, as well as the VR. But, if I disconnected all of the Caviar SEs from the RAID controller, I could install to the VR just fine, no power cycle behavior.
 
Solved!

Turn on Hot Plug in UEFI bios environment...

Thanks for the help however! Always great info on this forum.
 
Oh by the way, you can only RAID1 with 2 drives on this board. If you select more than 2 drives, it gives the error "NOT SELECTABLE: Mirror sets (RAID1) must have exactly 2 disks". I guess I can live with that...but I want to put that out there for anyone else searching.
 
I'm trying to use x64 OS's, so you mean x64 drivers, eh?

The driver that's been working for all drives, except the Caviar SEs, have been rcraid "AMD-RAID Controller [storport]". Is this a Promise controller? Chipset is A88X.

I set the array up in the RAID bios during boot. I also tried adding a 5th drive, leaving the Caviar SE's out of any RAID arrays, but attached to the RAID controller. The 5th drive was a single WD VR 80GB. When setup asked for the driver, and I tried to load it, the 4 Caviar SE drives did the same power cycle behavior, as well as the VR. But, if I disconnected all of the Caviar SEs from the RAID controller, I could install to the VR just fine, no power cycle behavior.


No..I always use the drivers from the x86 folder.
 
Back
Top