ASUS P8Z68-V pre-Windows keyboard issues

Ravynmagi

[H]ard|Gawd
Joined
Jul 12, 2006
Messages
1,464
Having some keyboard problems with my new ASUS P8Z68-V motherboard.

There is the symptom. After installing Windows 7 and installing a few drivers and things, after the last reboot the consistency checker came up for one of the 3TB hard drives. Not sure why that did. But it's takes for freaking ever to run. So I rebooted and tried to hit ANY KEY only to find the keyboard isn't working.

Keyboard works in the BIOS/POST. Then it seems to shut down just before loading Windows. Once Windows loads, the keyboard is working again.

Unfortunately just before Windows, I can't skip a disk check, I can't F8 to get to safe mode, I can't do anything with the keyboard. I've tried different keyboards. And this motherboard sadly has no PS2 port either.

I'm using the latest BIOS. So any ideas what's up with the keyboard support? Oh, I do have legacy keyboard support enabled (it was defaulted that way).
 
Are you using a USB 2 or USB 3 port? Also which model keyboard is it (part and revision number if any)?

-Raja
 
No. Don't see anything that looks like a revision number on either.

Microsoft Arc has Model 1392 on it though.

I have a few more keyboards I can try. Waiting for this chkdsk to finish, since I don't want to start it over again. :)
 
Some more testing.

During EFI POST, the keyboard works. I can get into the BIOS. However right when the American Megatrend screen comes up after EFI, it seems all my USB devices shut off. And from that point, until Windows starts up, they stay off.

I was finally able to cancel my chkdsk that comes up with Windows. I get a message saying to press any key within 10 seconds. At first the USB devices are still powered off. But right when that timer gets to 2 or 1 second, the USB devices power on.

Unfortunately I still have no means of doing F8 for safe mode though, as the USB devices all seemed to be powered off at that point.

I also tried the USB 3.0 ports. Also tried a Dell SK-8135 Rev 00 keyboard. No luck. Since all my USB devices seem to shut off for a while after the American Megatrends screen, I don't think any keyboard will get around this.
 
I think you need to enable "Legacy USB support" in order to use a USB keyboard in a MS DOS type environment, or the pre-windows command line. At least this is how it is on my GB board. On much older motherboards, this was called "USB keyboard support through Bios", to use a usb keyboard in MS DOS (or windows command line/boot menus).
 
Yes, Legacy USB keyboard support is enabled.

This is perplexing and disappointing. Is this issue normal for this motherboard?
 
Try the following please.
Before you get the windows 7 splash screen, mash F8 so you get the boot menu (this is the menu where you can choose Safe mode, or disabling driver signing, etc). You can also force the boot menu to appear every time by editing a startup file in msconfig. Does F8 work? Or if you edit msconfig to force the boot menu (i don't remember how; just search google), can you use the arrow keys to navigate?

If you can *NOT*, then it means legacy USB isn't really working at all. Oddly enough, I've actually seen legacy USB sometimes fail to work on my gigabyte board, but that was on an older BIOS, and hasn't happened recently at all. And I think it only happened if I was pressing keys to try to get into the BIOS or something and I pressed too late.

Also make sure all other USB devices are unplugged, just in case. There have been conflicts with the UEFI with certain devices in the past.

This wouldn't be the first time there were BIOS options that were inadvertently broken on a certain version. I remember an old Abit BH6 1.1 bios where cas latency changing didn't work (it was always set at 3 even if set to 2); they fixed that in a month, with a changelog.
 
I tried your suggestions and didn't have any luck with F8 or navigating the Safe mode menu.

It did seem to behave a bit better sometimes when I had fewer devices installed. So I started going through everything one at a time (with the keyboard too of course). After a while I found out the USB hub in my Dell monitor was causing the problem.

And then I realized I had some USB speakers plugged into that monitor USB hub. I removed those speakers (figured it was probably them and not the hub). And voila. Finally the keyboard is now behaving completely normally.

I can mash F8 and get the safe mode menu. I can navigate that menu.
 
Ok that's good. Yeah I remember lots of posts from people with problems with different USB devices, hubs or mobile devices plugged in during boots.
 
NEVERMIND... seems I spoke too soon.

This is weird. Once in a while it seems to work, then it stops again.

I'm also noticing some of my SATA drives are disappearing, the reappearing again.

And I also the Q-Fan control doesn't seem to be working. I was running Prime95 and saw the CPU temp up to 70C while the fan was running at 700 RPM (it was spinning faster earlier).

More I mess with this board, the more messed up it seems to be. I think I get a really defective product. I need to return this and find something else.

MSI Z68 GD65 a decent alternative?
 
NEVERMIND... seems I spoke too soon.

This is weird. Once in a while it seems to work, then it stops again.

I'm also noticing some of my SATA drives are disappearing, the reappearing again.

And I also the Q-Fan control doesn't seem to be working. I was running Prime95 and saw the CPU temp up to 70C while the fan was running at 700 RPM (it was spinning faster earlier).

More I mess with this board, the more messed up it seems to be. I think I get a really defective product. I need to return this and find something else.

MSI Z68 GD65 a decent alternative?

Hmm sorry I can't help further :( Perhaps just a RMA is in order? Or is this your first board?
 
Hmm sorry I can't help further :( Perhaps just a RMA is in order? Or is this your first board?

No, I've been building computers for a long time. This is my first ASUS board in many years though. Believe me, I don't normally have this kind of drama with a new motherboard. Think I spent 12 hours yesterday working on this. Was getting a bit loopy at the end there.

I can't figure out what the pattern is that's messing up legacy USB support. Once in Windows all the USB devices seem to be working.

Though it seems every 2 or 3 reboots. When Windows loads, I'll see a message saying new devices found. And it'll reinstall a USB device or SATA device. Kinda odd.

And while testing my CPU temps with Prime95. I noticed it started out fine at first. Then after a while the CPU fan speed (PWM fan with Q-Fan enabled plugged into the CPU fan header) will oddly just slow down. Using a sensor monitor I am able to see an extra "CPU" sensor has shown up that wasn't there before. And this sensor has a really low or really high temp.

I'll need to do some more search on this board before I decide to RMA or refund and get something else. Kinda nervous about getting another ASUS board after all the things that seem to have gone wrong with this one.
 
You can probably set up an advanced RMA so you get a new board shipped out and then return the old in the box (Newegg allows this). I hope your next board doesn't have this issue....
 
This sounds like some kind of strange power issue. Try unplugging the PSU, reseating all the cards, reattaching the 24pin and 8pin ATX connectors and booting back up. Then try adjusting your Vcore or other voltage regulation values in the BIOS and upping them slightly.
 
I think I have bottomed this one out with no solution from Asus technical support, who went thru the same time consuming Q&A. I wasted a great deal of time on this and hope I can help. f you have found a better solution please let me know The full details are posted below but the answer in summary is as follows: ….

“This issue can occur if your computer is connected to a Universal Serial Bus (USB) keyboard. Autocheck runs before USB support is enabled, between the point where the keyboard input is switched from legacy mode, to USB drivers. Note that this issue can occur even if your computer Basic Input/Output System (BIOS) is configured to provide legacy USB keyboard support. Because of this, the keyboard is not available when you try to skip the disk check. “ When you have a hardpower shutdown the chkdsk is automatically set to run.

I have made a work around using chkntfs /X to disable the disk checking and then a scheduled task under XP with a DOS/vbs batch filer to prompt for this at a later date within XP itself. Very very time consuming.!!! (A PS2 PCI card appears unlikely to provide a solution as this simply emulates a USB port.)

I was very disappointed in their support as I have requested a credit towards an upgraded replacement Deluxe MB which has PS2 support. I have yet to receive a response to this request made 14 December. (If I had known about this problem promptly I would have not have purchased the P8Z68 V and instead purchased the P8z68 Deluxe version which has PS2 support. It is essential at this time that I am able to run XP without this time consuming startup problem

By the way have you had any difficulties running legacy USB mice drivers under DOS. At the moment I am still unable to use several emergency recovery utilities which run under DOS because of legacy USB mice driver problems.


Good luck

Newkid11

Asus Ref : <TSD> Motherboard P8Z68-V [ID=RTM2011121301380-328]





See Microsoft Article ID: 240658 - Last Review: November 30, 2007 - Revision: 3.3
Cannot skip Autocheck at startup with USB keyboard
View products that this article applies to.
This article was previously published under Q240658
Expand all | Collapse all
SYMPTOMS
When you start your Windows 2000-based, Windows XP-based, or Windows Vista-based...
When you start your Windows 2000-based, Windows XP-based, or Windows Vista-based computer, you may be unable to skip the Autocheck process by pressing any key when you receive the following message
To skip disk checking, press any key within number seconds.
where number is a number that counts down from 10 to 0.
Back to the top
CAUSE
This issue can occur if your computer is connected to a Universal Serial Bus (US...
This issue can occur if your computer is connected to a Universal Serial Bus (USB) keyboard. Autocheck runs before USB support is enabled, between the point where the keyboard input is switched from legacy mode, to USB drivers. Note that this issue can occur even if your computer Basic Input/Output System (BIOS) is configured to provide legacy USB keyboard support. Because of this, the keyboard is not available when you try to skip the disk check.
Back to the top

Asus Ref : <TSD> Motherboard P8Z68-V [ID=RTM2011121301380-328]
 
Go into the BIOS / UEFI and enable Legacy USB keyboard support for the USB 2.0 controller. Ensure that the USB keyboard is plugged into the USB 2.0 ports and not the 3.0 ports. Past that you may have an issue with the board itself. I know you asked about the MSI board, and yes that's a decent alternative, if you don't mind the UEFI sucking. Aside from that you may have just got a bad board it happens. I'd RMA it if I couldn't make it work and try again.
 
It won't work. You NEED a PS/2 keyboard to skip the check unless the check is disabled. It's not possible to skip the disk check even on my 11 year old Abit BH6, where the keyboard works perfectly in pure MS DOS 6.22. The BIOS support for the keyboard is completely turned off at this point. This is the price you pay for buying a "modern" system without legacy ports, while using an older operating system that was never designed for a system without ps/2 ports (remember XP came out in late 2001)

You can't blame Asus for this, at all, when a 10 year old computer, that still had full and proper MS DOS support, including old ISA and shadowing features (since windows XP wasn't even OUT yet) has the same issue unless I use the ps/2 port.
 
Any update on this, did an RMA fix it for the OP? I have the same problem on my P8Z68-V where the USB keyboard only works 10% of the time between the BIOS (e.g. always works with F8 BIOS boot menu) and the boot of the OS (whether Win or Linux). This is really annoying with Windows recovery and grub menus.
 
I have the same problem with my P8Z68 Deluxe/Gen3 and my USB keyboard. No problem with entering the BIOS, no problem after Win7 has booted. Only when I want to select one of my installed Windows versions in the bootmanager the keyboard does not work.
What I found out accidentally: when I connect a second USB keyboard, *both* keyboards do work in the bootmanager. :confused:
Maybe you can give it a try and post your results.
 
I have had issues with keyboards in the BIOS / UEFI before and it was simply those keyboards. Some of them just have terrible firmware. The Razer BlackWidow and BlackWidow Ultimate come to mind as examples of this.
 
Asus's USB support sucks IMO. My old ABIT IP35Pro never had any problems with my USB keyboard/mouse. When I upgraded to SB I got a P8P67 Pro I found all sorts of odd behavior with it. USB has only been around since like '98? Who'd think it'd still be a problem getting basic devices recognized. I'm probably going to swap it out with an MSI board in a few days.
 
Having some keyboard problems with my new ASUS P8Z68-V motherboard.

There is the symptom. After installing Windows 7 and installing a few drivers and things, after the last reboot the consistency checker came up for one of the 3TB hard drives. Not sure why that did. But it's takes for freaking ever to run. So I rebooted and tried to hit ANY KEY only to find the keyboard isn't working.

Keyboard works in the BIOS/POST. Then it seems to shut down just before loading Windows. Once Windows loads, the keyboard is working again.

Unfortunately just before Windows, I can't skip a disk check, I can't F8 to get to safe mode, I can't do anything with the keyboard. I've tried different keyboards. And this motherboard sadly has no PS2 port either.

I'm using the latest BIOS. So any ideas what's up with the keyboard support? Oh, I do have legacy keyboard support enabled (it was defaulted that way).


Try toggling USB Full Initial in the BOOT options of UEFI and see if it affects menu selection during Win BOOT (if you are on the latest WIn7&Win8 EFI). I am not sure this will cure the problem, but it's worth trying.
 
Asus's USB support sucks IMO. My old ABIT IP35Pro never had any problems with my USB keyboard/mouse. When I upgraded to SB I got a P8P67 Pro I found all sorts of odd behavior with it. USB has only been around since like '98? Who'd think it'd still be a problem getting basic devices recognized. I'm probably going to swap it out with an MSI board in a few days.

It isn't ASUS. I've had boards from every manufacturer I've ever reviewed give me USB keyboard issues at one time or another. Gigabyte was the worst up until a couple years ago. My Razer Black Widow wouldn't work in BIOS for 90% of the boards I tested while that was on the test bench. My Coolermaster CMStorm QuickFire Rapid works on every motherboard I've tested it with. Including: Gigabyte Z77-UP4-TH, ASUS P8Z77-I Deluxe, P8Z77-V Premium, P8Z77-WS, Maximus IV Extreme, Maximus IV Gene, Rampage IV Extreme, ASRock X79 Extreme4, Gigabyte Z77-UD7, MSI Big Bang XPower II, MSI Z77A-GD41, MSI Z77A-GD55, MSI Z77A-GD65, Intel DX79SO and probably many I've forgotten.

Some keyboards have shitty firmware and do not work properly without the legacy USB mode being set in the UEFI/BIOS and some don't work right with some boards even then. Sometimes you have to unplug the USB keyboard and plug it back into a different port at POST, some may have to go to a different USB port, sometimes they'll work in native Intel USB 3.0 ports, etc. There are workarounds for the most part. Sometimes though you'll have to have another keyboard on hand. I kept a PS/2 mechanical keyboard that was 10+ years old around for that purpose.
 
I have the P8Z68-V Gen3 and have the exact same issues:

1. You literally only have 2 seconds to get past the disc check as well as a very small window to get into the F8 (boot menu). I literally have to keep pressing F8 throughout the entire boot. You can see your keyboard lights on briefly before turning off - then coming on again 2s before timeout.

2. I also have the issue with one SATA drive magically disappearing. It's on and off. This is the 2nd SATAIII port. Thankfully I'm installing it into my laptop soon so I won't need it any longer.

PS. Overclocking on this board is very hit and miss :(
 
I fiddled around in the BIOS and enabled the "EHCI Hand-off" option in the USB settings. This solves the problem for me - only one keyboard attached and it works in the windows boot selector menu! :cool:
 
Back
Top