P8P67 Pro B3 - CPU Red LED

...with two P8P67 Pros so far.

Bought it with a i5-2500k a couple of weeks ago and after two days the system just shut down while playing a video. First I though it was the PSU, but it turned out to be the mobo itself (at least that's what I thought). All components seemed to be running when trying to boot, fans were spinning etc., but nothing really happened (+ cpu led was on).
 
Last edited:
If you are getting a red light, on some boards that indicates overheating.. you may want to check and make sure everything was installed right.
 
@sanppa

What HSF are you using?
I was putting together another P67Deluxe today for my wife, using my fav HSF - the TR Venemous with the 1156 bolt thru kit (1155 and 1156 bolt pattern the same) and noticed something rather disturbing. Those 5 surface mount resistors on back of the board just adjacent to CPU brace plate were scary close to the edge of the TR backplate. I could just barely get a .001 piece of shimstock between the solder globs and the bracket edge. I then looked at my basic P8P67 and theres lots of room between the two. My other P8P67 deluxe is in a case which has no window, so i cant see how close they are in that one. I am thinking if that one had clearance issues, i would have spotted it. So I put the stamped steel bracket in a mill vise upright and used a 45 degree chamfering cutter to relieve the bottom edge so it freely cleared the surface mounts. I then repainted the edge with black spray paint. I also put 4 electrical tape squares on the top surface of bracket (slit with exacto knife in center to clear screw posts)

There are circuit traces everywhere on the ASUS boards - arent there supposed to be trace free zones where the HS mount goes?

So I say this because if one of those resistors is arcing to ANY backplate, then that would explain "CPU killer mobo" - but its not the mobo per se, just your choice of HS. Get out your magnifying glass and check!

Another thing to think about is with older PSU that have had their main 24 pin connector rocked back and forth many times to remove or install. This opens up the female connectors inside, so they perhaps do not make reliable sure contact. Might want to pary some contact cleaner in there too. Note that if a "new" CPU fixes the prob it may only be the connector was reinserted or cable move around

C'mon ASUS give us same amont of clearance as on P8P67 basic
 
cisco guy:
I've got a Scythe Ninja 3 and an XFX pro850w PSU, both are new.

You're right about there being absolutely no space between the Ninja backplate and the socket's metal backside. The plate seems to have some kind of a transparent coating on the side of the mobo, can't say anything about the material though.

ChRoNo16:
I don't think it's a problem with overheating, since the problem appears the instant I start the system.
 
Last edited:
I attempted to highlight the clearance space, either vertically or horizontally between the 5 surface mount resistors and HS mount plate on backside of mobo adjacent to metal CPU Zif socket plate. If it touches the resistors (or even close enough to arc) then the bracket wont sit flat and a plastic sheet insulator in middle section wont help anything.

Anyways i can now look at the Scythe Ninja 3 bracket for possible probs

Edit:
Interesting
Bracket center section is deeply recessed like the TR bolt thru
http://www.hardwaresecrets.com/fullimage.php?image=28440
The above link is from a Sep 2010 review - they had to have come out with a later version of bracket, but then again, that might be the one your vendor had laying around.
This one could def be a prob, but would need to know how wide it is at center, or a camera shot of the backplate installed from rear.
Thermalright Archon Universal bracket is 2 1/16" wide - clears easily
Thermalright bolt thru (comes with venemous) is 2 1/4" wide at center - unacceptable clearance to SM parts with latest vers of P8P67 Deluxe
>Something new to watch out for
All brackets clear P8P67 basic model SM's easily - dif layout
 
Last edited:
That is the same backplate in the pic that came with my Ninja. I'll try to get some pictures of it installed as soon as I can.
 
14kh0ls.jpg

23ssv2p.jpg


dunno if this would fry my CPU or mobo, its just a resistor, but couldnt help methinks
 
It looks pretty much the same with the Ninja backplate. It definitely touches the soldier bits. Dunno if it actually matters but might pose a risk...
 
Last edited:
Welp, I got the red light of doom today on my P8P67 Pro. It's been running fine since I got the second new board back from RMA. So about 3 months with just a few freezes. Today it froze, then powered off. When I turned it back on, the red cpu light was on, and the fans and other lights as well. But no beep, o hard drive noise, and no video signal.

I took it apart and checked all connections. Tried it with the bare amount of components and usb items plugged in. Tried one stick of memory in all the slots. Tried the mem ok switch. At my wits end. I've already filled out an RMA request with Asus. And now I'm searching for a non-Asus board, as I refuse to use Asus any longer.

If anyone's found a fix for this issue, please let me know so I can forgo a lengthy RMA.
 
@Cisco Guy, those are SMT capacitors used to decouple VCC. If they are shorted, you shunt VCC to ground which would either result in a board shutdown or something worse.

-Raja
 
@Cisco Guy, those are SMT capacitors used to decouple VCC. If they are shorted, you shunt VCC to ground which would either result in a board shutdown or something worse.

-Raja

Oh O.K. Those are caps.
So, the $64,000 question:
Could that in any way have possibly caused the frying of my vid ports - the 3 PCIe chanels are on the CPU die
 
@ officer921

I assume your first RMA was the B3 replace?
What was the second one for?
Have you tried the first obvious thing - a full cmos reset>
turn off PSU rocker (0)
unplug PSU
push "On" button in for count of ten
take out battery
Leave it like that for at least an hour - overnight even better
Reverse proceedure

The second most obvious thing is to try another PSU

I would also take off CM212 + and look carefully at mobo traces where top and bottom contact was to see if there are depressions in traces. I find it rather disturbing that ASUS puts delicate traces all around the four HS holes
 
i dont think its the cm212+, I have one, and the backplate is actually raised from the mobo on arms. Only the bolthrough portion of the bracket make contact with the mobo.
 
i dont think its the cm212+, I have one, and the backplate is actually raised from the mobo on arms. Only the bolthrough portion of the bracket make contact with the mobo.

Yeah, I just checked and I see what you mean. It just floats above the board backside.
 
@ officer921

I assume your first RMA was the B3 replace?
What was the second one for?
Have you tried the first obvious thing - a full cmos reset>
turn off PSU rocker (0)
unplug PSU
push "On" button in for count of ten
take out battery
Leave it like that for at least an hour - overnight even better
Reverse proceedure

The second most obvious thing is to try another PSU

I would also take off CM212 + and look carefully at mobo traces where top and bottom contact was to see if there are depressions in traces. I find it rather disturbing that ASUS puts delicate traces all around the four HS holes
First board was recalled, 2nd red light of death. The third board is coming from Asus. I've already ordered an Asrock Z68 Exteme4 Rev. 3 to replace the Asus board, which I will sell when it comes in.
 
Oh O.K. Those are caps.
So, the $64,000 question:
Could that in any way have possibly caused the frying of my vid ports - the 3 PCIe chanels are on the CPU die

Does the CPU still work? If it does then no. The PEG lanes on the board are traces only (with some compensation caps) so there is nothing to kill there unless the interconnect is physically damaged either due to warping or dry joints on the PEG connector legs.

-Raja
 
CPU still works perfect in 3 dif mobo
Replacement RMA P67 deluxe works fine
So what could fry the vid ports - vga red led?
Your best guess is cold solder joints on PEG connector?
I hate to have something go bad, and not have a clue why.
 
CPU still works perfect in 3 dif mobo
Replacement RMA P67 deluxe works fine
So what could fry the vid ports - vga red led?
Your best guess is cold solder joints on PEG connector?
I hate to have something go bad, and not have a clue why.

It would be down to a bad/broken joint either at the PEG slot/CPU socket BGA, or down to a break somewhere in the transmission lines.

-Raja
 
Hey Guys,

I know the thread is a bit old but thought I'd share my solution to a similar problem I had. I had the Asus P8P67 Pro board which I replaced with the B3 Deluxe version. Now I know there are differences between the boards but they are pretty much the same.

I installed my new Deluxe board and all I got was the CPU Led coming on and the machine shutting down. What the problem was that I had a case fan's power connected to a power connector just to the left of the cpu fan power connector and thats what the problem was.

Oddly enough this configuration worked perfectly on the old board. Simple issue but still very annoying.
 
@jjay-

Thnx for tip.
However its a bit confusing.
On my Deluxe 3.0 there is only a 4 pin CPU fan connector at top of mobo
On the Pro there are two extra fan connectors, one 4 pin chassis to left and one to right of CPU fan connector - a 3 pin "PSU" fan connector

So the questions are:
Did you put CPU fan connector into wrong input - the one on left top?
Are you ABSOLUTELY sure you got a Deluxe? On your mobo box, does label say Rev 3.1?
There is a 3.1 Pro, so wondering if a 3.1 deluxe actually came out?
 
Last edited:
Hey man,

Trying to remember now offhand, not by my pc. Correct me if I'm wrong. At the top of the mobo is the cpu fan connector and on the left is a 3 pin connector. Now I used to have a case fan connected to the 3pin connector like on my old pro board but moved it further down because it was stopping my pc from booting.

I'm absolutely sure I have the Deluxe and it is the new Rev 3, can't be sure offhand if its 3.1 tho. This is the motherboard, bought from a local supplier: http://www.prophecy.co.za/asus-p8p6...annel-ddr3-sandybridge-slicrossf-p-90605.html . I'll double check all this when I get home tho.

Also another thing to note for anyone having stability issues with their RAM. I've got corsair ram and my system would freeze within 5 mins of playing a game. Now I downloaded the bios "Beta Version 1703" which the description states as "Improved DRAM compatibility". I then selected "XMP" as my profile and the system is now rock solid.
 
Last edited:
Yeah, report back
FWIW the latest bios is 1850

I would have to say the greatest single cause of trouble on P67 Z68 mobo is not setting XMP in bios for RAM that has it on SPD chip. I really think they should put another sticker on the ram slots about XMP.

Asus default settings are a bit agressive for this type ram.
The AI Suite is also too agressive, but how many know how to set each and every option?
 
Yeah I actually tried the latest bios version. Lasted about 10 mins into a game instead of 5 mins then froze so used the previous version "1703" and played for about 3 hours with not one issue.

You right cisco that does seem to be the biggest issue, about not setting XMP in the bios for the RAM. I did actually try that first which did not work for me. The combination of the updated bios ver (1703) and setting XMP in the bios worked for me. Yeah there are alot of settings in that AI suite.

I found a great guide for oc'ing the 2500k. Guy managed a stable 5.1ghz using the same board as me which I will try soon, will updated you guys on another thread if it works out.
 
Back
Top