Vcore dangerously low?

RileyLewis

Weaksauce
Joined
Nov 8, 2006
Messages
114
Hey all.

I'm not new to building PCs, but I am new to any sort of overclocking. So new in fact, that I don't do it yet.

So I was surprised when my new system wasn't very stable. It would crash often (blue screen hardware failure), and was not related at all to heat.

I couldn't figure it out, and then one day my mb monitor (p8p67 le) popped up a Vcore error. So I checked the voltage...and it was at .984!

It varies wildly from 1.3 as a high, down to .984 as a low (usually around .990). As far as I can see it's crashing as the CPU is not getting enough power.

How can I fix this? I don't really know how to increase voltage, I know the theory but not the practice side of it. Any advice is appreciated. Does this sound like a lemon MB or CPU? Or is it something that can be fixed?

Basic details on relevant parts:

p8p67 le
i5 2500k
 
its dipping because if intel speedstep. it sounds like things are normal but if you want to be safe then disable speedstep.
 
voltage sounds fine.. like nova said thats the speedstep voltage.. so depending on the load of the processor the voltage will fluctuate with the cpu multiplier. sounds like something else is the issue. maybe check for a bios update.
 
Well you cant frag a processor with undervolting but you can lock a PC up and damage your data in ram and hard disk.
 
So maybe this is not it. I can't find the cause, and it's really annoying me. The system will lock up randomly (sometimes heavy load, sometimes idling). It goes bluescreen, with hardware failure, performs a memory dump (with vague info, of course), and reboots. Everything in the system is new (well except the case, and I'm really screwed if that's the cause ;) ).
 
I haven't seen many people with P8P67 LE's, but the "M" boards are already having enough issues as it is, being unable to set manual fixed voltages and relying on offsets...that just causes overclockers problems once they start pushing 1.4v...the vcore range gets too large to maintain stability going back and forth from idle to load.....BSOD's start happening.

Overclockers should be staying away from any board without manual fixed vcore adjustments.

If you're getting BSOD at stock speeds, then either BIOS update, or RMA the board and get a higher up model.
 
What about a ram problem...try running with 1 stick at a time and see...ck ram voltage too in bios and set it manually...
 
I couldn't figure it out, and then one day my mb monitor (p8p67 le) popped up a Vcore error.

I believe you need to extend the acceptable range for CPU voltage. I have seen this before when motherboard monitoring software was alerting you for perfectly acceptable conditions.

So I checked the voltage...and it was at .984!

It varies wildly from 1.3 as a high, down to .984 as a low (usually around .990).

0.984 is totally fine when idle and in C1E mode. I believe some CPUs will go even lower.

As far as I can see it's crashing as the CPU is not getting enough power.
Does it crash always when you are not taxing the CPU or does it crash when your are playing games ...

How can I fix this?

Disable power saving if you really want to keep the CPU from dropping the voltage that low.. As I said before this is normal.

Does this sound like a lemon MB or CPU?

Neither motherboard nor CPU sound like they are bad.

Or is it something that can be fixed?

I believe the crashing has nothing to do with your CPU going into the deep power saving mode (C1E) when the cores are idle.

Like others said I would check the memory. Especially if you are overclocking your CPUs ram controller which in the case of the lga1155 processors means if you run faster ram than 1333 MHz. In this case you may need to increase the voltage in the ram controller (IMC).
 
Before he goes and runs RAM tests he should really make sure he's on the current BIOS (with a CMOS clear after) to help ensure proper compatibility and such.
 
I'd suspect a RAM problem before an issue with Speedstep/C1E.

Run Memtest x86+ and see what happens. It doesn't take very long.
 
Back
Top