P8P67 Pro Instantly rebooting

Italiano86

Limp Gawd
Joined
May 26, 2008
Messages
252
I received my new replacement board today, after my previous one basically fried, and cannot get it to post no matter what I try. First time I started it up it would not post but sit at the dram light and just remain solid. I held the button to let it reboot a bunch of times to let it do it's thing for a few minutes and nothing was progressing so I turned it off, and now it reboots every 3 seconds, no matter what.

Have cleared cmos, as well as the memory jumper again and again, and it will just continuously reboot after 3 seconds repeatedly until I turn off the psu. Asus made sure the board was good before they sent it out, I'm totally lost right now. I have also tried one or both sticks of my memory in different configurations, and no go. I know it's late, but maybe someone can give me some pointers, I'm going insane, lol.
 
If you're completely sure that everything is plugged in properly (check the cables!) and that your CPU or RAM isn't damaged, then the board is just bad or the BIOS is corrupted. If doing a long cmos clear (unplugging PSU, removing battery and shorting cmos and leaving it for a few hours) doesn't help, then the board is dead.

How do you know that all your other parts are good, though?
 
I don't know the other parts are good, but using either stick of memory has the same result, and the cpu light never stays solid, which should tell me the cpu is fine. Could never get it to post. I pm'd gary a more detailed description, I'll paste it in, but I'm going to bed, lol.

"I get the solid red dram light no matter what. Holding the button it does it's blinking cycle while the light cycle speeds up and then finally boots again, to show the solid red light again. This is with both sticks of memory, or either one in any slot, doesn't matter. To make things more random, sometimes with any configuration the computer will get into an infinite boot cycle, rebooting every 3 seconds. This can happen before or after the dram button being held to reboot, or just after a cold boot, again, have not seen the bios a single time.

I have cleared cmos over and over again, using the cl rtc jumper with mixed results as well, nothing is working. The cpu light is never solid, so this tells me the cpu is fine, I hope, lol. One ram stick was not in when the original mobo fried, so I highly doubt both sticks would be mysteriously defective, but I can't tell with only my 2 sticks."

But yea, my original mobo worked for almost 3 weeks then decided to cook itself, with only one stick of memory in, so I doubt both are bad.
 
Talked to the tech in Indiana who is an asshole unfortunately, and he asked me if I had the manual for the mobo, lol. Told me the memory had to be on the qualified vendor list but the sticks worked in my previous mobo just fine. He said my memory controller could be bad, or the dimm slots, and I would need to test my cpu and processor in another board to see what it does, but I don't have access to another mobo, cpu or memory, any ideas?
 
I had the led memory problem when I first tried my board and thought it was DOA. Had a RMA ready to go and had everything broken down already before I gave it another try.

First I did a proper clear cmos with the battery out and left it on clear for about 5 mins. Then only installed cpu and 1 stick of memory and it started up. It seemed like it had something to do with using a2 and b2 ram slots. I put my sticks in a1 and b1 and it worked.

Not sure if this is still an issue with the latest bios but if your still having problems maybe your memory was also fried?
 
This whole thing is a nightmare. I'm going to BBY to buy a stick of CMXG2GX3M1A1333C9 or a set of CMX4GX3M2A1333C8 to see if anything changes. Will post back in a little while.
 
you mentioned twice that the first board "fried"
what do you mean by fried exactly?
two boards in a row not working means its on your end
You are going to have to take out that water block and use a regular HSF
Does its backplate clear all the stuff on the back of the mobo correctly?

some genius decided to make the ram slots with only a single lock tab
with my sticks it took a humungous amout of pressure to get them down all the way. I would take the board out of case to make sure they are in properly
 
Yea, the first board's vrm mosfets fried, the ones right under the left blue cooler, had about 2 melt the solder points and smoke, basically spewing their contents on the heatsink. WHen this happened only one stick of mem was installed.

Used the single stick of CMXG2GX3M1A1333C9 I bought for $25 and it's also a no go. Any slot, same result, it won't even stay on and have a solid dram led like the other stick of vengeance. All it does is start booting before even post, and restarts in like 3 seconds, which goes on forever. Funny thing is one stick of the vengeance does this too, but the other does not, as often anyway.

I am thinking the incident fried my cpu as well, would intel even cover this since it was the mobo's fault? I used a different cpu and vga card as well, same result, even using the oem intel cooler right now and no dice. The backplate is rubber with plastic o-ring standoffs, so definitely no short there.

Here's my original post with a couple pics of the fried board. Gary won't be in I think until monday so I get to wait again, lol. They said this is the first board that has melted like this, pretty crazy.
 
Just called fry's and told them what happened, they are going to see if I can exchange the ram and cpu for another one hopefully, just waiting to hear back from them. This is assuming the board asus sent me was indeed tested and worked just fine, I hope if they exchange out the mem and cpu then everything should work after. If not, then I am screwed
 
dunno, waterblocks make me nervous
either that or you could be bending pins when installing CPU, possibly when rolling back the lever. Get one of those cheap magnifying glasses and look inside the socket. Did you check there in orig mobo after meltdown?

and assuming you also cooked the original cpu, you now say "tried a dif CPU"
You have 2 Sandy Bridge CPU?

I would be very curious to see what Frys does in this case
 
Last edited:
I guess I meant gpu or mem and typed vga also, I only have one. Water is perfectly safe, never had a leak and I use compression fittings. Water was definitely not the cause of the last mobo going bad. I know for sure the pins are good, checked both mobos, and the pens are all perfectly symmetrical. Still waiting for their call back.
 
be sure and try the new stuff out of the case

I guess no PC is almost as bad as no sex - just more tension
;)
 
Lol, everything is out right now, if the board is the culprit, I will go crazy. I am keeping everything out until the stuff checks out. I still don't know 100% if my vid card is ok, but I doubt it just went bad. I have a feeling the board is messed up even though Gary and his friend tested it, but I will still get new ram and cpu to be on the safe side.
 
I always keep a bunch of junk stuff around to test with when things go bad
like a PCI vid card and cheapo 1066 1.5V RAM 1GB
http://www.bestbuy.com/site/EVGA+-+...&ref=06&loc=01&ci_src=14110944&ci_sku=1734043
have to make sure you set boot PCI first in bios
the only way that melt can happen is with arcing somewhere
one time i pulled a ram stick out one side up first not noticing the PC was still shutting down and got a giant blue arc from edge to slot. Looked just like lightning
amazingly didnt hurt anything
once again - make sure rams are DOWN!
 
Went to fry's and the manager let me swap out the cpu and memory. I mentioned sandy bridge recall and he just said it's fine, lol. Took it home and the bitch finally posts. Seems like my cpu was officially fried. Memory was probably ok, but didn't want to have to deal with another rma so I just swapped it out to be on the safe side. Just running one stick right now so it would boot, need to add the second and adjust the timings since it would give me the solid red led with both sticks. I'm happy though, it's working! lol

I figured the mobo was good since Gary had it tested before it shipped, I'm just shocked the original mobo took out the cpu. I'm thinking maybe the memory controller was fried, and maybe the rest was ok, but now I'll never know. I think the new cpu I got uses more voltage than the last one which is a bummer, but at least it works.
 
Yeah, mosfets frying has a VERY large chance of causing the CPU to get a nice healthy dose of pure 12v. The mosfets are made to regulate and convert power, and when the magic smoke comes out, you don't know whats getting 12v for even an instant....

If a PSU dies, one with properly working protection will prevent the board from getting a surge that takes out components with the PSU, though whether it shuts down fast enough is anyone's guess. But mosfets are a different story...
 
Funny thing was the computer originally did not want to stay turned on. It would just start up and instantly turn off, which I should have though, oh, better stop, lol. It only booted up when I removed a single stick of ram, then fired up literally, which is when I noticed the smoke. PSU seems fine otherwise, not sure if it was the cause or not to be honest. It's the only thing I have not changed out, but everything is running awesome now, just need to overclock again. One thing I remembered, one time I booted the computer using auto voltage settings at 5ghz, and the voltage read 1.6v. I immediately shut it off, but I am on water and the temps were like 30c, but I still turned it off immediately. This was a couple weeks before the mobo died, not sure if it's correlated or not.
 
Auto voltage settings are for people that don't know what their doing and if you need it or use it imho
you shouldn't be overclocking .

Really i don't know why anyone adds this kind of junk to any mobo and or makes overclocking apps with a
easy button for people that don't know what their doing .
I had that happen to me once as well when i first got my core 2 mobo .
Stupid thing tried to put my ddr2 ram at 2.1v for some Mentally retardation reson .
I picked up on it real fast but i wasn't a happy camper after i saw that and disabled everything i could
find in the bios on the auto overclock topic.

Its the fastest way to destroy your computer as far as im censored.:p

By overclocking you void all warranties and my self if i were a shop owner and i learned you did i
wouldn't reimburse you on anything.:D
 
lol :D
i found this really cool auto overclocking app out their. download now! =)
And when i said my gigabyte mobo tried put my ddr2 ram at 2.1v i mean i didn't even touch the bios .
I just pulled it out of the box when it was 100% new and was doing the first test run ever with it on my work bench with nothing but a psu\ram\video card\cpu.
I picked up on it cus the memory got hot and fast using my trusty finger testing probe.
Options_SelfDestruct.png
 
Last edited:
I know what I'm doing, it was a little program called auto overclocker by asus, Kyle even used it to see what it could do. There was no way I could know it would put that much voltage through the chip. Was curious if my chip could reach 5ghz and asus touted the program as safe, but apparently it's not. Other than that, I would never use a program to oc, it's bios or nothing.
 
Auto voltage settings are for people that don't know what their doing and if you need it or use it imho
you shouldn't be overclocking .

Really i don't know why anyone adds this kind of junk to any mobo and or makes overclocking apps with a
easy button for people that don't know what their doing .
I had that happen to me once as well when i first got my core 2 mobo .
Stupid thing tried to put my ddr2 ram at 2.1v for some Mentally retardation reson .
I picked up on it real fast but i wasn't a happy camper after i saw that and disabled everything i could
find in the bios on the auto overclock topic.

Its the fastest way to destroy your computer as far as im censored.:p

By overclocking you void all warranties and my self if i were a shop owner and i learned you did i
wouldn't reimburse you on anything.:D

Boards are NOT supposed to FRY out and explode. So yes he deserves a reinbursement. And I hope you never get a job in a store, because if I were your customer, I would chew you out so badly, you would wish you never went to work that day...
This is why the average idiot on these forums can't just go get a job in a computer store...
 
By overclocking you void all warranties and my self if i were a shop owner and i learned you did i
wouldn't reimburse you on anything.:D

All I can tell you is karma is a bitch, and hopefully you are never in my situation, it's not cool. When a motherboard has built in overclocking tools and advertises the fact, then wouldn't it be safe to say people will overclock? Even a small amount, doesn't matter. Some retailers ie: microcenter have service plans to cover oc damage.

The motherboard should not have put that much voltage through the board, I just read that kyle had the same problem, it fed his chip 1.64 volts and he barely caught it.

I work at a comp store, and I would hate to have to work with you, lol.
 
Last edited:
I know what I'm doing, it was a little program called auto overclocker by asus, Kyle even used it to see what it could do. There was no way I could know it would put that much voltage through the chip. Was curious if my chip could reach 5ghz and asus touted the program as safe, but apparently it's not. Other than that, I would never use a program to oc, it's bios or nothing.

Similar with my RE3 - on auto(not even using Asus o/c tool) it sets CPU and other volts way to high if I even mildly o/c, so it's a manual setup on most of it. I would also agree these mobos are NOT meant to fry out, they have plenty of 'safety features' in CPU and mobo to stop that, so overclocking or attempting is moot IMO when it comes to board failure. Modding the boards however is a different case - you mod, you usually void warranty:D...usually;);););)
 
My Asus P8P67 will enter a continuous reboot loop if my external hard drives are plugged into the USB ports. Have you removed all your peripherals and tried booting?
 
My Asus P8P67 will enter a continuous reboot loop if my external hard drives are plugged into the USB ports. Have you removed all your peripherals and tried booting?

I was booting with nothing more than the video card and ram to eliminate all possibilities. Turns out the cpu was dead, possibly the memory controller because of the dram light. Will never know since fry's is sending it back to intel most likely.
 
Back
Top