Gigabyte Mobo stuck in boot loop

westsrides

n00b
Joined
Dec 3, 2007
Messages
30
Hard Folks,

I just installed a Gigabyte GA-EP43-UD3L mobo w/ 6GB RAM (2-2GB sticks, 2-1GB), Geforce 9800GT PCI-E vid, Intel E7200 processor, an IDE DVD & HD and two SATA HDs.

Often the system will enter a boot loop upon power-on or reboot every 2-4 seconds- not enough time to enter BIOS. Sometimes it won't loop and will post and load Windows 7, but usually doesn't.

I've tried clearing the CMOS by jumping the terminals and by pulling the battery. I've tried pulling both types of RAM and trying them in different combinations.

I've read about this problem on other forums- but the posts were back in 2009 and I never saw any solution. Anyone know of any?

Pulling my hair out here.

Thanks,
James
 
If it goes into boot loop, turn the power switch off on the PSU and turn it back on.

Make sure your bios settings are correct/stable for your hardware. Use one stick of ram only in slot one for testing purposes.

I've seen this behavior on a lot of Gigabyte boards, it is starting up and shutting down because it's having trouble posting because of some hardware failure or incorrect/aggressive settings and it's trying to find something that works. Usually it's ram related.
 
Thanks. When I have made it into BIOS, I have set everything to non-overclock settings. i have tried all 4 sticks of RAM one at a time and have had it fall into the reboot loop with each. I'm looking at drivers and flashing the bios now.
 
Interesting to me that its able to run stabily for so long, but as soon as it reboots or is shut down and turned on it often falls into a loop.
 
unplug all of your usb devices and see if it exhibits the same behavior.
 
do you mean the internal USB devices, like the ports on the front of my case that plug into the motherboard, or the external devices like my keyboard, mouse, etc? I had heard this suggestion before and thought the author was talking about internal connections, but I haven't considered the external ones.

If that works, what does that mean? Does that indicate something that can be fixed?

All this said, the computer has been running stably since about 9pm last night. never flashed the bios but did update all the drivers from Gigabyte. I've rebooted the computer several times without any loops.

But, this happened yesterday, too, where it seemed fine for a while, rebooted fine a few times, but then started looping again. Could it be a bios setting? The Award Bios on this mobo has more options than I've ever seen.
 
do you mean the internal USB devices, like the ports on the front of my case that plug into the motherboard, or the external devices like my keyboard, mouse, etc? I had heard this suggestion before and thought the author was talking about internal connections, but I haven't considered the external ones.

If that works, what does that mean? Does that indicate something that can be fixed?

All this said, the computer has been running stably since about 9pm last night. never flashed the bios but did update all the drivers from Gigabyte. I've rebooted the computer several times without any loops.

But, this happened yesterday, too, where it seemed fine for a while, rebooted fine a few times, but then started looping again. Could it be a bios setting? The Award Bios on this mobo has more options than I've ever seen.

just the external devices. i had a USB hub that would cause my gigabyte mobo to reboot inifinitely...ive read a couple other places about USB devices affecting boot-up of gigabyte motherboards.

it couldnt hurt to disconnect your front usb ports from the header on the motherboard just for troubleshooting purposes...
 
The mixed memory that you have installed in your system is partly to blame, in this case. Modern memory controllers don't like being run with mixed memory modules of mixed IC densities. Most 1GB DDR2 modules are double-rank using 512 Mbit (64M x 8) ICs while all 2GB DDR2 modules are double-rank using 1 Gbit (128M x 8) ICs. The mixed IC densities present an even greater load on the system's memory controller than even using four modules with the exact same identical ICs. In fact, I have not had much if any success with simultaneous operation with mixed-size memory modules and ICs in the same system since the days of PC100 SDRAM memory.
 
Last edited:
The mixed memory that you have installed in your system is partly to blame, in this case. Modern memory controllers don't like being run with mixed memory modules of mixed IC densities. Most 1GB DDR2 modules are double-rank using 512 Mbit (64M x 8) ICs while all 2GB DDR2 modules are double-rank using 1 Gbit (128M x 8) ICs. The mixed IC densities present an even greater load on the system's memory controller than even using four modules with the exact same identical ICs. In fact, I have not had much if any success with simultaneous operation with mixed-size memory modules and ICs in the same system since the days of PC100 SDRAM memory.

Nonsense. I'm running a couple of pair of old 1GB DDR2 modules and a pair of 2GB modules. There was a thread a while back on this; plenty of us are doing it.

Plus - read the posts - he's tried each stick of RAM individually.

Did you try a reset of the BIOS back to factory defaults, just to make sure?
 
just go with 2 sticks until you get the issue solved. make sure that vdimm is whatever the memory requires. default may be 1.8v but the memory may specify more.
 
Nonsense. I'm running a couple of pair of old 1GB DDR2 modules and a pair of 2GB modules. There was a thread a while back on this; plenty of us are doing it.

Perhaps because it's just my luck. None of my old 1GB modules worked at all with any of my 2GB modules even at the lowest clock speeds with the loosest timings and the highest voltages (266MHz/DDR2-533, 6-6-6-18, 2.1V) regardless of the motherboard I used them on. The three motherboards (all of different brands) that I tried them on all failed to even POST - and in my case, they all hung at POST (yes, not even the reset or power buttons worked at all when it hung), forcing me to physically unplug the entire system and wait a few minutes before plugging it back in. And each and every module came through Memtest without errors. And yet those same motherboards worked very well with 4 x 1GB modules provided that their SPD settings matched the supported memory speeds and timings for the processor's FSB. (I did not attempt 4 x 2GB modules because I have only two DDR2 modules of that size.)
 
Last edited:
Once you get it to boot again, try the restore fail safe settings option in the bios. You will probably have to do some custom manipulation of the timings. That setting should make them as lax as possible for the time being. It is possible that your board has a defect that is intermittent with temp change.

You also didn't indicate what type of Power Supply you have. Perhaps, you could try another one? I once saw this problem in a case with a broken power switch. The switch felt just fine. I found out when I tried unplugging it and shorting the pins with my screw driver. Note: It didn't do it all the time. Sometimes it would stay on as long as no one so much as breathed.
 
Back
Top