Lasers Replacing Spark Plugs

Almost correct but multiple ignition points will cause knocking. The aim is to have a variable ignition point so that the engine can use an inhomogenous air fuel mixture. Less fuel will be needed for the engine to run at low load.

This is where the feedback system will come in to play.
Using real time information, the timing and intensity of each spark can be adjusted.
Detonation and Pre-ignition will become problems of the past.
 
This is where the feedback system will come in to play.
Using real time information, the timing and intensity of each spark can be adjusted.
Detonation and Pre-ignition will become problems of the past.

Detonation and pre-ignition are already problems of the past, even with a spark plug. The ignition time, valve timing and fuel injection are already being controlled by the ECU on modern cars based on the feedback from the sensors like knock sensor and lambda sensor.

Btw I'm glad to see someone who understands what is it all about, not like most people who posted. :cool:
 
the reason is, physics. once you ignite the fuel, it will burn the same whether you ignited it with a spark or two sparks (or 4). once the fire is lit, its lit... thats why sparks plugs can never increase power. if your plugs are weak and failing, then of course youll get misfires and loss of power, but that just broken parts. any decent plug lasts 40k miles at least anyway, i dont see why this is a big deal at all. if anything, the lasers could potentially last forever, so it would be much like going from distributors to coils packs... doesnt change much other then reliability/durability.

I have to side with you on this one. Why does this even matter unless it is for an alternative fuel (hydrogen). Spark plugs are cheap anyway. The speed of electrons vs light is negligable in this application. I just don't understand why this is needed at this point in time. It is almost more of a tech demo than practical application. Unless they are looking towards laser induced plasma engines. In which case cool:cool:
 
Sorry, didnt explain myself well enough.
I meant micro detonation and pre-ignition that will occur at the individual ignition points, this can be almost instantaneously controlled now.
Unlike multiple spark systems where there is no inherent technology to collect such precise ignition data.
Lasers can of course be used in spark ignition systems for data collection (not ignition), a good way to test the concept and the self calibration system, instead adjusting each sparks intensity and timing.

nb in my previous post I said
"the timing and intensity of each spark can be adjusted"
It should read
"the timing and intensity of each laser ignition point can be adjusted"
 
I'm pretty sure there will be ignition converters some how for older cars. Its like what happened with fuel injection and spark plugs and everything.
 
didnt see anyone mention Pulstar plugs yet, we just started carrying them at Advance Auto Parts, if the numbers they claim are able to be realized in real life, they are a pretty significant upgrade for some vehicles such as the Honda S2000
 
I've always thought the whole idea of sparking each and every time was the wrong way to go...

Thinking like a starter piston for a old style locomotive, once it starts in one direction - there is no need to use it again as the main engine takes over.

The best way to have it work would to be somehow capture a tiny portion of the flame from the first piston and move it to the second piston and sucessive pistons with a slight delay. In such a way - the alternator (which runs about 60% efficient) could be taken out of the picture entirely.

I see potential in the laser idea, in that once the laser ignites the fuel, the laser energy can potentially be captured or redistributed to the other pistons in a very efficient manner.

Too bad we can't use a Tritium ignitor... Those last for decades.
 
Laser will work better for direct injection inside the cylinder head, you can have an inhomogeneous mixture.

There are already inventions for Gas Engines that are much more efficient than the 4 times Engine, If they are willing to use these lasers then why not use those Engines?
 
Almost correct but multiple ignition points will cause knocking. The aim is to have a variable ignition point so that the engine can use an inhomogenous air fuel mixture. Less fuel will be needed for the engine to run at low load.

That's where you spend more of the gas right?
 
There is also the fact that a laser travels at the speed of light throughout the cylinder before ignition. A spark travels nowhere near as fast or far inside the cylinder before ignition. Makes sense.

Well slightly true, the laser won't quite go 'c' simply because it's traveling through a gas mixture, but ok really fast. But a spark doesn't need to travel that fast, it ignites and the chain reaction with other gas molecules is what does further ignition, same as a laser (the laser would not ignite everything simultaneously.
 
I know how to pump my own gas. That is as technical as I get with cars.

Unless you live in Oregon, of course! I was very bothered by their law, so when traveling across the country I topped-off at the Washington-Oregon border and was hoping to make it through to California without needing to fill up...worked out very well! =]
 
Unless you live in Oregon, of course! I was very bothered by their law, so when traveling across the country I topped-off at the Washington-Oregon border and was hoping to make it through to California without needing to fill up...worked out very well! =]

Don't forget New Jersey! Many moons ago my mom was in NJ and didn't know you couldn't pump your own gas, so she got out of the car and started doing it herself. Let's just say the gas station attendant was not pleased.
 
Does anyone know why that actually even exists? That annoys the hell out of me every time I drive thru Oregon.

Anyways back to the topic, this just seems like massive over complication to me unless they can get the instantaneous feedback that Nenu was talking about. Otherwise I'd say it's not going to be cost effective. And congrats to Ford for surviving and spending their own money on R&D.
 
I've always thought the whole idea of sparking each and every time was the wrong way to go...

Thinking like a starter piston for a old style locomotive, once it starts in one direction - there is no need to use it again as the main engine takes over.

The best way to have it work would to be somehow capture a tiny portion of the flame from the first piston and move it to the second piston and sucessive pistons with a slight delay. In such a way - the alternator (which runs about 60% efficient) could be taken out of the picture entirely.

I see potential in the laser idea, in that once the laser ignites the fuel, the laser energy can potentially be captured or redistributed to the other pistons in a very efficient manner.

Too bad we can't use a Tritium ignitor... Those last for decades.

Well diesel doesn't need a spark plug, diesel is self ignited. The latest technolgy being developed is an engine that behaves in between a diesel and a gasoline engine. An engine that can run in homogenous air fuel mixture and also self ignited.
 
Well diesel doesn't need a spark plug, diesel is self ignited. The latest technolgy being developed is an engine that behaves in between a diesel and a gasoline engine. An engine that can run in homogenous air fuel mixture and also self ignited.

If diesels could be engineered to spin to the same speeds as gasoline engines, I'd be sold. All that torque with a high redline would be amazing. Can't have your cake and eat it too I suppose.
 
If diesels could be engineered to spin to the same speeds as gasoline engines, I'd be sold. All that torque with a high redline would be amazing. Can't have your cake and eat it too I suppose.

Diesel ICEs have come a long way since the 80s :) Especially here in Europe they're quite common, even in small cars. Having driven both types (diesel and gasoline), I have to say that it's hard to notice the difference. The type of car and its general construction will have more effect on performance.

That said, anything to make gasoline ICEs more efficient is welcome in my book, as long it's reliable and not too expensive.

*still waiting on a European version of the Chevy Volt herself*
 
If diesels could be engineered to spin to the same speeds as gasoline engines, I'd be sold. All that torque with a high redline would be amazing. Can't have your cake and eat it too I suppose.

Spinning faster really isn't important. I'd like to think Audi's R10 proved that, properly designed, a diesel engine can do whatever you usually do with a gasoline engine.
 
For more power you can either have a higher rev or a higher torque. A higher torque is better for acceleration but you will be limited by your tyre.
 
Does anyone know why that actually even exists? That annoys the hell out of me every time I drive thru Oregon.

I believe there was some sort of accident (atleast in NJ) and a politician thought it needed a law passed.

As a car nut, I never let an attendant pump my gas (most dont give a damn if they over-turn the gas cap/drip gas on the paint/etc), so I feel for you guys that live in those states. It would drive me absolutely insane
 
If diesels could be engineered to spin to the same speeds as gasoline engines, I'd be sold.

Why? It is not an advantage that a gas engine runs at higher speeds. It is a disadvantage that a gas engine cannot make the same level of power without being run at that faster speed. Fuel efficiency decreases and engine wear increases as rpm increases.
 
Doubt it will make much difference. If a better plug could produce better power (and in turn mileage) manufactuers would be using them. They have toyed with some two plug heads but even that was ruled to be not worth the effort. My 96 ford ranger 2.3 had 2 plugs per cylinder.
Not to mention the manufactuers could be putting in those split whatever plugs and send lots more juice to em. It just hasn't turned out to be worth it. Not even in formula 1 etc... They do probably run coils that are hot as heck but I bet they run plain ol iridium plugs.

You got it a bit wrong....the prupose of the dual plug heads on the Ford Lima engines was to reduce emissions by assuring all fuel is burnt before the exhaust valves open. Thus two plugs to create two points of ignition, thus assuring that the side opposite of the plug, where combustion was least likely to occur, does occur.

There was a serious power gain when going to the dual plug head for an entirely unrelated series of design changes. The dual-plug heads have a montrous port job on them (so monster that those heads are illegal for all racing applications a Ford Lima would be considered for)....those heads also are mated with fuel injection (as opposed to the carbeureted engines prior to that) which offers better control of the air/fuel ratio, thus more economy and better performance.....the entire intak/exhaust is better flowing, and the kicker....the compression is higher. This was enough to go from 80hp to 110hp for the Mustang version of the engine.

All the dual-polug was for is that....emissions.
 
All the dual-plug was for is that....emissions

I'm sure the top fuel and funny car guys are concerned about emissions with their nitro burning dual plug hemi engines.
 
You got it a bit wrong....the prupose of the dual plug heads on the Ford Lima engines was to reduce emissions by assuring all fuel is burnt before the exhaust valves open. Thus two plugs to create two points of ignition, thus assuring that the side opposite of the plug, where combustion was least likely to occur, does occur.

There was a serious power gain when going to the dual plug head for an entirely unrelated series of design changes. The dual-plug heads have a montrous port job on them (so monster that those heads are illegal for all racing applications a Ford Lima would be considered for)....those heads also are mated with fuel injection (as opposed to the carbeureted engines prior to that) which offers better control of the air/fuel ratio, thus more economy and better performance.....the entire intak/exhaust is better flowing, and the kicker....the compression is higher. This was enough to go from 80hp to 110hp for the Mustang version of the engine.

All the dual-polug was for is that....emissions.
Dual plug is used because the flame can't travel fast enough from the point of ignition so some fuel far away can be ignited by the explosion wave and that will cause knocking.
 
The best way to have it work would to be somehow capture a tiny portion of the flame from the first piston and move it to the second piston and sucessive pistons with a slight delay. In such a way - the alternator (which runs about 60% efficient) could be taken out of the picture entirely.
A spark plug is going to consume on average, in the order of a single Watt. This isn't exactly a huge energy drain, and doesn't strike me as a problem that needs fixing.
 
A spark plug is going to consume on average, in the order of a single Watt. This isn't exactly a huge energy drain, and doesn't strike me as a problem that needs fixing.

With the AC sucking down hundreds of Watts, not to mention the dozens of gadgets (audio systems, iPods, navigation systems, seat heaters, massage seats...), it does seem indeed silly to worry about a few measly Watts consumed by the spark plugs :)
 
Yes and in retrospect, it's probably closer to a hundredth of a Watt on average.
 
With the AC sucking down hundreds of Watts, not to mention the dozens of gadgets (audio systems, iPods, navigation systems, seat heaters, massage seats...), it does seem indeed silly to worry about a few measly Watts consumed by the spark plugs :)

I think it might also be about timing though. There might be some lag effects with spark plugs that if eliminated may allow for tighter timing of the engine cycle? Just my 2 cents.
 
true, but the biggest advantage is burning the fuel more efficiently and having the ability to change it's temperature/intensity on the fly. It opens the door to a while bunch of new technologies that couldn't of been implemented before

You could argue that the early variable valve timing systems and even overhead cam designs were a little redundant, but today 400HP is nothing for a modern engine due to technologies like it. Back in the good 'ol days of the muscle car wars, 400HP was a big deal (and sucked down fuel like it was going out of style).
 
Yeah, as quoted from the article:

"The laser also produces more stable combustion so you need to put less fuel into the cylinder."

In current engines spark plugs are positioned at the top or bottom of a cylinder and they can often fail to ignite fuel effectively if the petrol is not in the right position in the cylinder.
 
1) this is old - although if they are getting this closer to production this is good
2) just use diesel, it ignites under pressure
 
With the AC sucking down hundreds of Watts, not to mention the dozens of gadgets (audio systems, iPods, navigation systems, seat heaters, massage seats...), it does seem indeed silly to worry about a few measly Watts consumed by the spark plugs :)

The problem with gasoline, it won't ignite if lambda is not equal to 1. It is not about spark plug efficiency, it is about the ignition point. The ignition point must be at where the lambda is equal to 1. It is almost not possible to run a gasoline engine with an inhomogenous mixture if the ignition point is fixed at one point. To run a homogenous mixture, you need much more fuel than what is necessary. Unlike diesel, you can't inject less gasoline with excess air into the combustion chamber.
 
Its all cute but the number one breakthrough still required to make the ICE much more efficient is:

Computer controlled valves. Not the bullshit VTEC or other marketing hype crap.

I'm talking total control of the shape of the valve timing curve, and lift.

This controls beyond all other factors the torque curve of the engine, By completely controlling it, you can completely change the behavior of the ICE. Right now, with the effectively fixed valve timing and lift (though VTec type crap does fiddle with it a bit) leads to the prnounced torque peak of the ICE, so at RPM X the engine gets its maximum efficiency, and off the peak it becomes alot more wasteful.

Having a totally variable valve timing, you can widen the torque peak to cover a huge range, say 1500 to 4500 RPM, rather than being a sharp peak at 3200 RPM.

It also plays into allowing and complementing the control of intake/exhaust flow rates, to keep the air flow in/out velocity as high as you can, and it can also mimick variable compression ratio, which can help make startup and the interaction with turbocharging easier and cleaner emmisionswise.

A ROD RATIO of 2:1 or better, large piston diameter and short stroke. Cylinder/piston skirt coatings of teflon, and piston/combustion chamber coatings of ceramics will all improve efficiency and cut back on energy as heat being wasted heating up the metal of the engine rather than making the wheels turn.

Complete control of the ignition and valve lets you implement near zero loss selective cylinder shutdown. So cruising down the highway, a ZR1 Corvette would be running on effectively 2.5 cylinders and getting 40+ MPG all the while that 550HP is ready for action with the twitch of the right foot.

The cylinder shutdown gambit really requires the ability to crack the intake open (with fuel injector NOT firing) and to crack the exhaust valve open, to minimize any parasitic losses from false compressions. It also allows zero cost implementation of the "air pump" and "egr" functions, simply by letting fresh air into the exhast for the cats and letting exhaust back into the cylinder at the end of the exhaust cycle. Saving $100-200 per car.

Combine this with a computer controlled manual transmission ACTING like an automatic, the driver would never know the difference, but a flawlessly operated manual will always be much more efficient and long lived than any automatic transmission ever can be.

Then there is a manner of "Hybrid"ness that can be added to this, that supports true full regenerative braking and a hybrid boost mechnism similar to the Honda Civic hybrid design, and you get some very very high mileage results oout of easily implemented technology. Hint: batteries cannot support the charging rate needed by true electric bake energy recovery.... but getting to save and reuse that energy stored in the cars momentum is the equivalent of the enrgy we can save by doing conservation efforts in our homes... it is energy we are currently wasting, but could easily recoup and save alot of $$ and CO2 in the doing.

The Auto industry will never do all these things, because they actually SUCK at making cars.
 
Great idea. :cool: Just make the car doesn't malfunction such that the hood pops off and the laser points up toward an airplane. :eek:
 
Its all cute but the number one breakthrough still required to make the ICE much more efficient is:

Computer controlled valves. Not the bullshit VTEC or other marketing hype crap.

I'm talking total control of the shape of the valve timing curve, and lift.

This controls beyond all other factors the torque curve of the engine, By completely controlling it, you can completely change the behavior of the ICE. Right now, with the effectively fixed valve timing and lift (though VTec type crap does fiddle with it a bit) leads to the prnounced torque peak of the ICE, so at RPM X the engine gets its maximum efficiency, and off the peak it becomes alot more wasteful.

Having a totally variable valve timing, you can widen the torque peak to cover a huge range, say 1500 to 4500 RPM, rather than being a sharp peak at 3200 RPM.

It also plays into allowing and complementing the control of intake/exhaust flow rates, to keep the air flow in/out velocity as high as you can, and it can also mimick variable compression ratio, which can help make startup and the interaction with turbocharging easier and cleaner emmisionswise.

A ROD RATIO of 2:1 or better, large piston diameter and short stroke. Cylinder/piston skirt coatings of teflon, and piston/combustion chamber coatings of ceramics will all improve efficiency and cut back on energy as heat being wasted heating up the metal of the engine rather than making the wheels turn.

Complete control of the ignition and valve lets you implement near zero loss selective cylinder shutdown. So cruising down the highway, a ZR1 Corvette would be running on effectively 2.5 cylinders and getting 40+ MPG all the while that 550HP is ready for action with the twitch of the right foot.

The cylinder shutdown gambit really requires the ability to crack the intake open (with fuel injector NOT firing) and to crack the exhaust valve open, to minimize any parasitic losses from false compressions. It also allows zero cost implementation of the "air pump" and "egr" functions, simply by letting fresh air into the exhast for the cats and letting exhaust back into the cylinder at the end of the exhaust cycle. Saving $100-200 per car.

Combine this with a computer controlled manual transmission ACTING like an automatic, the driver would never know the difference, but a flawlessly operated manual will always be much more efficient and long lived than any automatic transmission ever can be.

Then there is a manner of "Hybrid"ness that can be added to this, that supports true full regenerative braking and a hybrid boost mechnism similar to the Honda Civic hybrid design, and you get some very very high mileage results oout of easily implemented technology. Hint: batteries cannot support the charging rate needed by true electric bake energy recovery.... but getting to save and reuse that energy stored in the cars momentum is the equivalent of the enrgy we can save by doing conservation efforts in our homes... it is energy we are currently wasting, but could easily recoup and save alot of $$ and CO2 in the doing.

The Auto industry will never do all these things, because they actually SUCK at making cars.

There are a few ways to control the valve timing already but you can't remove the cam shaft because using any other methods to manipulate the valve like using electromagnetic and hydraulic would be inefficient compared to camshaft and spring.

Shutting down the cylinder is a great idea but unless you have a lot of cylinders, shutting down one cylinder will make the engine unbalance and it will do more harm than good.

A continous variable automatic transmission would be much more efficient than any human controlled manual transmission.

The Auto industry has already considered doing all these things but they didn't do it since people would rather pay for fuel than paying more to save fuel. Once the fuel price is high enough, more technologies will be implemented since it will be cheaper to pay for the technologies than paying for the fuel.
 
Back
Top