[H] Cable Management

HardOCP News

[H] News
Joined
Dec 31, 1969
Messages
0
[H] reader Edward Cabarles sent me this picture of the world’s best/worst cable management system ever. How can it be the best AND worst? Best: because they got it all in there. Worst: when a cable needs to be replaced…yikes!
 
[H] Cable Management

[H] reader Edward Cabarles sent me this picture of the world’s best/worst cable management system ever. How can it be the best AND worst? Best: because they got it all in there. Worst: when a cable needs to be replaced…yikes!

TEXT

Comments

Heh.
 
ummm

nice Steve, Forget to paste the correct link to the picture???? :p
 
meh,

looks like a typical phone co's hub office.. The wiring is the give away ;)
 
Jesus H Christ! What's the name of this datacenter? I'm blacklisting them.
 
Last I checked that passing electricity through a wire creates a small magnetic field. Cluster enough wires together and now you have a huge magnetic field, which can interfere with data.

Won't data corrupt going through there? Is there a sign there that says don't walk in here wearing Ferrous metals?
 
Wow :eek:, that is crazy but yes I agree on that it will be a pain to replace a cable! :eek:
 
Guys this is most likely a telco switch cell site. Nothing new here, this is what they do, actually I'm quite surprised that they did such a clean job compared to what they normally do. Wires on these sites typically does not need to be replaced, when they do, they just toss on another line.
 
ummm

nice Steve, Forget to paste the correct link to the picture???? :p

Jeez, you guys are bad, some times it takes a minute or two for the image to show.

GJSNeptune posted 37 seconds after this post was made, you posted 61 seconds after him. Everyone that clicked the link after 1 minute and 41 seconds saw the image just fine.

LOL!!

Patience is not a virtue in the [H] forums...you have to give it a second fellas, give it a second :D
 
Last I checked that passing electricity through a wire creates a small magnetic field. Cluster enough wires together and now you have a huge magnetic field, which can interfere with data.

Won't data corrupt going through there? Is there a sign there that says don't walk in here wearing Ferrous metals?

A wire that is coiled (like a spring) with a current running through it will create a magnetic field (an inductor). Two wires (really) close together will create a minuscule amount of capacitance.

Wires arranged like that, especially when shielded and insulated, won't really have an effect on each other, or at the very worst it'll be negligible.
 
This makes my inner standards monger alternately weep and rejoice for the whompin' about to be delivered.
 
I can't tell if its good or bad......but I know if the support structure broke and someone was under it we could have a new story about the first person to die from computer cables falling on them.
 
I can't tell if its good or bad......but I know if the support structure broke and someone was under it we could have a new story about the first person to die from computer cables falling on them.

The ladder system wont break. Believe it or not that you can walk on them without any risk.
 
It is a telco hub and it is probably VERY old (at least 15 years). This is how they did it folks, tons of parallel runs as clean as they could. When one breaks, you switch over to another line. While "these days" we do things different, this was the standard at the time.
 
It is a telco hub and it is probably VERY old (at least 15 years). This is how they did it folks, tons of parallel runs as clean as they could. When one breaks, you switch over to another line. While "these days" we do things different, this was the standard at the time.

Do you happen to have a picture on how one would handle that many cables today?
 
It is a telco hub and it is probably VERY old (at least 15 years). This is how they did it folks, tons of parallel runs as clean as they could. When one breaks, you switch over to another line. While "these days" we do things different, this was the standard at the time.

Mine sharing how things are done differently these days as opposed to back then? :)
 
GJSNeptune posted 37 seconds after this post was made.

After my first post, I navigated my way to the image. Went to the home page, then the news item, then I found and viewed the image just fine! :D
 
Mine sharing how things are done differently these days as opposed to back then? :)

They don't tend to run that many single pairs that "size" any more. They will running bundles to effectively a "data concentrator". Then you can run a single line. Our bulding use to have this problem because nearly all the phones (over 2000 when to a single choke point). Now, about 200 phones go to a single box and that box goes via fibre to the main system for our phone network. No different than hooking up 10 or 15 PC to a hub and running a single wire back to a switch. A ton less copper at the expense of some efficiency.
 
Single twisted pair unshielded was a dead giveaway that it's a telco office. Nobody else really uses wire like that. As for the electro-magnetic issue, that's all low voltage stuff, nothing to really worry about. Now i've seen some power cable trays that will stop your watch. It's really cool walking through a high voltage substation and having the hair on your arms stand up due to the static electricity.
 
Single twisted pair unshielded was a dead giveaway that it's a telco office. Nobody else really uses wire like that. As for the electro-magnetic issue, that's all low voltage stuff, nothing to really worry about. Now i've seen some power cable trays that will stop your watch. It's really cool walking through a high voltage substation and having the hair on your arms stand up due to the static electricity.



one of my instructors told a story about a high voltage substation where the grounding grid had failed, ground water had leached the salt bed under the substation I think.

repair tech goes in to check on a problem, puts a foot inside the station and boom, instant BBQ.
 
I can't tell if its good or bad......but I know if the support structure broke and someone was under it we could have a new story about the first person to die from computer cables falling on them.
The ladder system wont break. Believe it or not that you can walk on them without any risk.
Ladder racks very are strong provided the installer is competent and follows proper guidelines, though I have seen anchors pull out of cement ceilings, but it's very rare (sucks I was on the rack when it happened). I've never seen so much anodized rack (last I knew that stuff was hollow, but sure is pretty hehe), Primarily good old heavy as hell solid steel gray rack is used in telco co's. Used to lace down a lot off 350 & 750 MCM power cable as wide as the rack & several layers high, with a ground run hung below on L brackets...that's a LOT of weight, especially fun when going between floors, add in a few installers crawling around (occasionally napping away a hangover) wrestling that into place & lacing it down...ah, good old waxed 9 cord (tie wraps are for pussies (and usually not allowed) lol).

This takes me back to my telco central office install days, but cable racks were used for sheathed cable, typically 25-125 pair (the cables seen on the upper rack, which I must say is an embarrassing mess) connecting the switches to the mainframe where cross connects were done, that and power cable for the equipment, but I never saw any thing like this cross connect extravaganza. There were standards we had to follow (anyone who knows what a "beer stitch" is and what hell it can cause you should it be spotted by some hardass, or the ever popular "no dips, no divers" rule, knows about serious cable management). I'm really surprised they didn't pan that rack, it would've negated the stress each rung puts o the wire.
As far as replacement, I'd imagine it's the same...if it can't be moved to the new location, cut both ends & leave it, pull a new one, once it gets too full, it's "cable mining" time (oh what fun that is).
 
Ladder racks very are strong provided the installer is competent and follows proper guidelines, though I have seen anchors pull out of cement ceilings, but it's very rare (sucks I was on the rack when it happened).

Yeah, I'm assuming it was installed at least to spec. My worst fear is falling off these damn things and having your leg stuck in the pegs. *snap*


I've never seen so much anodized rack (last I knew that stuff was hollow, but sure is pretty hehe), Primarily good old heavy as hell solid steel gray rack is used in telco co's.

It's not anodized. It's just the regular plated. Most ladder vendors like newtwon instruments carries it in their standard glazed color (color you see), the ibm white, the telco gray, and then the modern black.

Hollow or solid is also an option, the solid stuff is shit heavy. When I mean shit heavy I mean shit heavy, especially the wide ladder option with the added cross braces for extra strength. I wouldn't think twice about putting over 1,000lbs on any section on that. Stuff is strong.

Used to lace down a lot off 350 & 750 MCM power cable as wide as the rack & several layers high, with a ground run hung below on L brackets...that's a LOT of weight,

Yep, about 1lb per ft. That is a whole lot of copper. Stuff is also heavy.

especially fun when going between floors, add in a few installers crawling around (occasionally napping away a hangover) wrestling that into place & lacing it down...ah, good old waxed 9 cord (tie wraps are for pussies (and usually not allowed) lol).

Worked for ATT? They are gunhoe about wax string. They kinda still are but it's a dying trade. I really enjoy the work wax string provides you and the perfection of the install.
 
Jeez, you guys are bad, some times it takes a minute or two for the image to show.

GJSNeptune posted 37 seconds after this post was made, you posted 61 seconds after him. Everyone that clicked the link after 1 minute and 41 seconds saw the image just fine.

LOL!!

Patience is not a virtue in the [H] forums...you have to give it a second fellas, give it a second :D

But but but, I live my life a quarter mile at a time here Steve!
 
Jeez, you guys are bad, some times it takes a minute or two for the image to show.

GJSNeptune posted 37 seconds after this post was made, you posted 61 seconds after him. Everyone that clicked the link after 1 minute and 41 seconds saw the image just fine.

LOL!!

Patience is not a virtue in the [H] forums...you have to give it a second fellas, give it a second :D

It still just goes to hard OCP for me.
 
Wow I looked at that and thought, what that cable running off to the side next to the AC conduit? Then realized that wasn't an AC conduit!
 
Insanity. Looks very routine and very clean, but gigantic.
I can imagine much worse types of wiring in these setups.

Must have taken forever to wire that.
 
Back
Top