PC8500 reading as 400mhz?

johnnyrebel87

Limp Gawd
Joined
Feb 12, 2009
Messages
187
Me and my buddy finished our pc's yesterday. We both have a biostar 790gx board, and a phenom II 940 cpu, and 4 gigs 1066 ram. Well we both looked in bios and the ram was at 800. We changed it to 1066, and we both installed cpu-z to see if that's what it was running at. It says both of ours are running at pc6400! I have g-skill pi ram and he has mushkin ram. Both have 2x2gb. We look in the bios again, and it says clock is 1066. Why does it say we're running pc6400 400mhz in cpu-z? Is there any other way to see what speed our ram is running at?

Thanks guys, we're completely stumped :(

Ian
 
Screw CPU-Z, if it runs fine, it is fine. :0
Also my PC6400 shows as 400mhz, but that's the DDR2, it's actually 400mhz x 2 = 800mhz.
 
Are you looking at the SPD tab or the MEMORY tab? If you are running DDR1066, you should see 533mhz under the MEMORY tab.
 
I'll have to check that out. I remember seeing that, but it also says pc6400 in it also. Maybe I can figure out how to take a screenshot and post it.
 
ALT + Print Screen takes a photo of your desktop. Paste it into paint, resize if necessary.

But, no need to post a pic unless you just really want to. Just read the frequency under the MEMORY tab and post what it says.
 
Not to derail but I had to give props to Mike for helping out all memory users, not just Corsair customers. Bravo.
 
Just as an FYI, My Corsair PC8500 shows PC6400 in the SPD tab, but runs happily at PC8500 speeds and shows as 533 in the memory tab....
not sure whats up with that, but its weird...
 
Just as an FYI, My Corsair PC8500 shows PC6400 in the SPD tab, but runs happily at PC8500 speeds and shows as 533 in the memory tab....
not sure whats up with that, but its weird...

DDR2 modules MUST be able to boot at JEDEC 1.8v, DDR800, and 5-5-5-15 or so timings. When you boot a MOBO for the first time or after a CMOS clear, the BIOS is at the defaults. So, it cannot boot high performance memory that has tighter than JEDEC timings, higher voltage requirements, etc. That's why the SPD is set to these settings. Once you manually set your memory up, you can toss the SPD info out the window, figuratively of course. The info that is important to determine your settings and frequency are under the MEMORY tab.
 
DDR2 modules MUST be able to boot at JEDEC 1.8v, DDR800, and 5-5-5-15 or so timings. When you boot a MOBO for the first time or after a CMOS clear, the BIOS is at the defaults. So, it cannot boot high performance memory that has tighter than JEDEC timings, higher voltage requirements, etc. That's why the SPD is set to these settings. Once you manually set your memory up, you can toss the SPD info out the window, figuratively of course. The info that is important to determine your settings and frequency are under the MEMORY tab.

See, I knew there was a good explanation..

Thanks for the info Mike, and my memory runs just fine...right up to 585Mhz.....then it gets a bit unstable..naturally I will deny that if I ever have to RMA them..:)
 
See, I knew there was a good explanation..

Thanks for the info Mike, and my memory runs just fine...right up to 585Mhz.....then it gets a bit unstable..naturally I will deny that if I ever have to RMA them..:)
No worries, frequency won't damage the memory and is not an RMA concern. It's that pesky voltage thing.
 
Back
Top