How does this Order look, and other WCing questions

colinstu

2[H]4U
Joined
Oct 11, 2007
Messages
3,563
I've become increasingly more interested in watercooling. WC setups look much nicer then a TRUE120 and a HR-03 GT.

1) What kind of temps do you get at 100% load on a Q6600 @ 3.6GHz or similar? It seems like once people go water you can go break through the barrier that air can't when it comes to OC.

2) What are good sites to buy most of wc parts? (Rads, tubing, pumps, blocks, etc).

3) For a Q6600 OC + 8800GTX or two SLI, would a 3x120 rad be adequate? Anyone play with 4x120?

4) Are there rads with a in and outtake on opposite sides (vs the in and out on one side).

5) What is better. Res>pump>rad>cpu block>etc **OR** Rad>res>pump>cpu>etc

6) How much does gravity effect it (water flow, etc?). Should the tube for the res (in T shape), have a slight U shape so water goes into the pump vs res?

7) Do you need a res? Can you just keep some extra hose or...?

I'm thinking of hitting up an Antec 900, Corsair or better PSU, 680i or 750i board, Q6600, 1-2 8800GTX's, 2 150GB raptors, and all the water cooling supplies.

-What are the best rad's (makers, specs, efficiency on them vary?),
-Best pumps for working a long time, powerful.
-Many different CPU blocks out there, are the best ones with those copper pins (more surface area?), same deal with NB. Guessing there are 680i blocks, how about 750i?
-Good maker of nvidia full cover blocks (GPU, mem, mosfests, etc) for different models, 8800GTX/8800GTS 512/new cards, etc.

Here is some MS paint editing fun of kinda the idea. Hide the pump and res in the top drive cage, Rad completely over the top, the pink is for a tube that can only go on the same side as the other tube, yellow is if it can be opposite.
 
1) What kind of temps do you get at 100% load on a Q6600 @ 3.6GHz or similar? It seems like once people go water you can go break through the barrier that air can't when it comes to OC.

This is all dependent on what else is in the watercooling loop. Generally though an ideal OC with a good watercooling setup will not exceed 40c on the CPU and that's in a pretty small room.

2) What are good sites to buy most of wc parts? (Rads, tubing, pumps, blocks, etc).

Petratechshop, Danger Den, Performance-PCs

3) For a Q6600 OC + 8800GTX or two SLI, would a 3x120 rad be adequate? Anyone play with 4x120?

Yes (I would also cool the NB if you plan to OC)

4) Are there rads with a in and outtake on opposite sides (vs the in and out on one side).

Usually rads have holes on either side and you can screw anywhere from 2 - 6 fans on there.

5) What is better. Res>pump>rad>cpu block>etc **OR** Rad>res>pump>cpu>etc

You can set this up however way you want but make sure that the pump is after the rad and before the cpu

6) How much does gravity effect it (water flow, etc?). Should the tube for the res (in T shape), have a slight U shape so water goes into the pump vs res?

As long as you have a good pump, gravity shouldn't be an issue (at the very least go for a D5 if you want a full cpu,2gpu,nb setup. You never want a complete 90 degree angle on any of your lines (except for maybe the fillport if you have one), otherwise it will reduce pressure.

7) Do you need a res? Can you just keep some extra hose or...?

No, you can have a complete loop with just a fillport.

I'm thinking of hitting up an Antec 900, Corsair or better PSU, 680i or 750i board, Q6600, 1-2 8800GTX's, 2 150GB raptors, and all the water cooling supplies.

-What are the best rad's (makers, specs, efficiency on them vary?),
-Best pumps for working a long time, powerful.
-Many different CPU blocks out there, are the best ones with those copper pins (more surface area?), same deal with NB. Guessing there are 680i blocks, how about 750i?
-Good maker of nvidia full cover blocks (GPU, mem, mosfests, etc) for different models, 8800GTX/8800GTS 512/new cards, etc.

-For money/performance stick with either Thermochill or Swiftech
-For a Quad you want more surface area. A full cover GPU is nice but you are restricted to that one block and will not be upgradable for future cards. NB you want to at least cover the entire size of the chipset.
EK, Danger Den are good makers of full cover blocks
 
Stuff = Swiftech
Place = Performance-PCs
Case = CoolerMaster 830 EVO + 1000W PSU deal, read this:http://enthusiast.hardocp.com/article.html?art=MTQ2NSwxLCxoZW50aHVzaWFzdA==
Route: rad>res>pump>cpu>gpu>rad. Reservoir is a good idea. Get a MicroRes from Swiftech
I have a Q6600 with a Swiftech Apogee GTX block, temp never goes over 40C.....no one runs benchmarks all day. I report temps that my CPU sees in everyday gaming use. OCs really vary with CPU type and motherboards so as always your mileage may vary. My Quad has been running faithfully for almost a year at 3.1 GHz, my MB just wont let it go higher, but its a fine place for me.

Remember a GPU block isnt reusable. Performance will answer any questions about GPU, NB blocks.
 
Remember a GPU block isnt reusable. Performance will answer any questions about GPU, NB blocks.

A full cover block is not reusable. There are GPU blocks that aren't full cover that are reusable with a plate change.

I've had my MCW-60 for a while now and between cards I just change out the adapter plate.
 
What kind of fitting should I use? Is cooling performance a little better if you use a wider tube? 1/2" seems to be the biggest for the DD blocks.

Also been having second thoughts on the full cover GPU blocks. Never realized how expensive they were. I'm not going to be voltmoding them, should I just get some stick on heatsinks for the memory?

Despite all the horror stories of 680i, I'm sure it will be stable under some water and a 400MHz bus.

Thanks for answering my questions!

EDIT: What kind of tubing? I know 1/2ID, but there are different brands of it :p
 
What kind of fitting should I use? Is cooling performance a little better if you use a wider tube? 1/2" seems to be the biggest for the DD blocks.

Also been having second thoughts on the full cover GPU blocks. Never realized how expensive they were. I'm not going to be voltmoding them, should I just get some stick on heatsinks for the memory?

Despite all the horror stories of 680i, I'm sure it will be stable under some water and a 400MHz bus.

At DD, little confused about the GPU blocks. Do you have to buy this and this?

Thanks for answering my questions!

EDIT: What kind of tubing? I know 1/2ID, but there are different brands of it :p

The MAZE-5 is a complete kit, the top you link is optional and not necessary.
I use 3/8 inch ID tubing, some people swear by 1/2" ID, but its big and somewhat more difficult to route.
I use the cheapest clear vinyl tubing I can find, I dont thnk it matters. I buy my tubing from FrozenCPU and use their "house-brand" that costs about 2 bucks a foot. If I have a tight bend I use the Swiftech Coils.
I watercool one of my GPUs essentially because I needed to use the PCI slot adjacent to it. The full cover block made it a single slot solution. Honestly, if it wasnt for that Id just leave it alone and let the aircooler do its job. If you are not going to OC the GPUs watercooling may be more of a pain in the ass than a help.
 
Looks good.
Just make sure the MAZE fits your GPU, and check that the other stuff is compatable with your hardware.
You might get 10 feet of tubing to be safe.
You need connectors to secure the tubing, i use these:http://www.performance-pcs.com/catalog/index.php?main_page=product_info&cPath=298&products_id=3803

some people like to go to Lowes and buy small hose-radiator worm clamps, but I found them to be too bulky. Obviously you need one for each connection.

You'll need some distilled water (from the drug store) and a water additive like this:http://www.performance-pcs.com/catalog/index.php?main_page=product_info&cPath=384&products_id=1955

Are you ordering a CPU cooler??
 
Bah, I screenshoted an older cart by mistake. Come back to check the cart and it's empty :(

This is the CPU block.

Edit, could I just use zip ties and fasten them really hard ;)


TDX is not as efficient for the quads as the maze-5s are because of the surface area.

I'd stick to the Maze-5 for the cpu and/or get the Swiftech APOGEE GTX
 
TDX is not as efficient for the quads as the maze-5s are because of the surface area.

I'd stick to the Maze-5 for the cpu and/or get the Swiftech APOGEE GTX

There is no Maze 5 for the cpu, it was for the gpu.

So the apogee gtx over the TDX from DD?

EDIT: Updated cart. Still a little curious about anti-corrosive stuff, the sticky mentions PT nuke, magoo mentions this. UV reactive... is it green? Ideally I'd like to keep everything clear, or blue.
Am I missing any plates/adapters/brackets/etc?
 
There is no Maze 5 for the cpu, it was for the gpu.

So the apogee gtx over the TDX from DD?

EDIT: Updated cart. Still a little curious about anti-corrosive stuff, the sticky mentions PT nuke, magoo mentions this. UV reactive... is it green? Ideally I'd like to keep everything clear, or blue.

Sure there is:

http://www.dangerden.com/store/product.php?productid=280&cat=61&page=1

I know cos i've got one LOL.. heres a pic just in case you're interested, not as flashy as an acrylic top but just as potent ;) :
n5249633_43327913_266.jpg
 
I am late to this party but I would suggest the Dtek Fuzion with the nozzle kit for a CPU block and if you want the very best Rad I'd go with Thermochill.

Good stores are Jab-tech and Sidewinder.
 
Well......
1) I really like my Apogee GTX, and it doesnt have those long screws to look at, I find it pleasing to the eye and it cools like a bandit.

2) The Swiftech coolant is green, you can buy coolant in any color you want, I happen to like the green, but you can get clear or blue additive, just look around.

3) if you order kits, like a Swiftech Apogee block from anywhere, you will get all the mounting hardware you need.....some places will give you fittings for the hose in a choice of 3/8 or 1/2", some will only give you a single choice and some places you have to pay extra. Performance-PCs gives you a choice at no extra charge.

4) some folks use zip ties to mount their hoses, two per. I really have no faith in that.....look, a small plastic fastener costs 50 cents or something. A small price to pay for not leaking coolant all over thousands of dollars of computer parts.
No matter what, always leak test the circuit for 24 hours before running the computer for use.
 
Top of the line quad wc blocks right now are (in no particular order):

maze5cpu, apogee gtx and dtec fusion

hands down dont look anywhere else its just preference on look really... some like brass top, some like acrylic and some like the stainless look.

Zip ties are a pain in the ass, not worth the hassle, u may end up knicking your tubing while trying to cut them. Reusable plastic clamps are cheap, easy to use. Don't kid yourself, you WILL be making adjustments to tubing lines so just don't hassle with the zippies.
 
Okay thanks everyone! Couple days ago I would have no idea about water cooling. Now I know where to look/look for, etc.
 
Back
Top