Its alive! QUAD SLI !!

No, my friend, it's you that's mistaken. The special 3-way SLI bridge requires that the cards have two bridge connectors on top. You'll notice the 9800GX2 only has one connector on top, which means it cannot do more than Quad-SLI. Sorry.
Exactly. I was saying needed bridge in my posts when I meant needed bridge connections which added to the confusion I think. :eek:
 
Eh, I'm not sure if I would trust those temps, that just seems too high to be reasonable. Can anyone else with a 9800GX2 post there GPU temps?

If those are correct then holy shit that's hot.

They are accurate they are being reported that way on 3 programs

However it was just with the .70 drivers I think they fucked the fan speed, changed all my fans on the lower level to blow out since the 9800 GX's2 blow the heat back into the case instead of out like the 8800's. Temps are safer now

WTF1.jpg
 
Much better. Which driver version did you end up using? Or does RivaTuner work on the GX2s?
 
So, the the single 9800GX2 can't run Crysis at 4x AA on 1680x1050..?
 
Also, those temps aren't anything to worry about. The 8800GT can run at 110°C just fine, and it's the same core.

same core but smaller at 42nm instead of 65nm which is what the 8800GT has also this is why the 9800GX uses less voltage.

@Airmanv are you using the official drivers? have you tried any of the tweaked drivers like those from tweakforce.com?
 
Whoever said that these 9800GX2's cant run Tri-SLI should read up on them. Tri-SLI essentially is 6 - GPU's (Each 9800GX2 is dual 600Mhz GPU's) so basically each card is already in SLI itself, sticking three together will give you tri-SLI.

No, I don't need to read up on them. I own two of them and they don't have the connector required to run 3-Way SLI. The NVIDIA drivers also don't support 6 GPUs. YOU are the only who needs to do some reading.

Now how you ask? You do need a nVidia 790i or a 780i board to be able to do it. You also need some serious freaking power. Also March 25th nVidia is releasing the drivers to handle tri SLI with these, so yes it is possible and can be done.

Again you obviously have no clue what you are talking about here. If you did you would know that 3-Way SLI doesn't require a 790i Ultra SLI or 780i SLI board. A 680i SLI board will do.

Additionally NVIDIA is releasing new 9800GX2 QUAD-SLI drivers. Not 3-Way SLI drivers. 6 GPUs aren't possible currently. Period.

The spec's call for a min 600W PSU. I run a 850W PSU, called EVGA because I am doing the step-up and dumping my 8800GTS KO's 640MB cards for 2 of these 9800GX2's and they told me I should have a minimum of 1000W PSU to run these in SLI.

So if you are talking Tri-SLI, you are probably looking at a 1200w to 1300W and possibly a suplimental running periphals like a Thermaltake 350W that fits in the CD/ROM slot in your chassis, but yes it is possible.

It also seems your knowledge of how computer power supplies work needs improvement as well. Theoretically 3-Way SLI with three 9800GX2's wouldn't need 1,000 watts at all. In fact I'd be surprised if they pulled over 750watts under load. You wouldn't need a 1200watt PSU or higher and you certainly don't need any supplemental supplies either. If you actually looked at some actual data on how much power many high end system configurations actually draw you'd know that the 1kw requirement mentioned by NVIDIA is nothing more than a blanket statement the company makes because they know many people will have shitty power supplies that can't actually handle what they are rated for. If forces people to think they need higher minimum power requirements than they need so they'll buy higher end units. This prevents a certain amount of technical support headaches right from the start.

Heat? Yeah, these babies are hot, what do you expect? Hell, my 8800's in SLI idle at 60C +, run Crysis in the mid 70's. I have 5 - 120mm case fans at high most of the time in my Antec P180B, plus the fans on the cards run around 80%. I cna idle them around mid-50's if alll fans are on and ambient temp is around 60F. According to EVGA they say not to worry till they reach mid 90's, so WFE. I was used to my 7950's running mid 30's, but oh well, with power you get heat. If you want to play with power you got to expect it.

This last statement is about the only thing I can remotely agree with.
 
First of all, way to go Airmanv, thats some rig you got there, I am looking forward to how it performs both before and after upcoming driver revisions are dropped.



Hmmm, who says he made the rig for any one game? Look despite what many feel about the game itself, it is one of the few games that cannot be maxed out with steady high frame rates without edits and config tweaks. As such it has become almost a milestone. So whenever there is a uber rig made some have to wonder how it handles Crysis. If it was not for guys like Dan and Airmanv blazing a trail with this stuff how would we find the compatibility issues with say a MegaRAID BIOS?

Good luck with the rig Dan hope you get it up and running soon.



Good post !

And WTF is with all the haters and thread bashing of late ?

Seems we have lots of jealous little boys,still living with mommy and daddy on here. :p

The more things change the more they stay the same....

Congrats OP very nice system !
 
Whoever said that these 9800GX2's cant run Tri-SLI should read up on them. Tri-SLI essentially is 6 - GPU's (Each 9800GX2 is dual 600Mhz GPU's) so basically each card is already in SLI itself, sticking three together will give you tri-SLI.

Now how you ask? You do need a nVidia 790i or a 780i board to be able to do it. You also need some serious freaking power. Also March 25th nVidia is releasing the drivers to handle tri SLI with these, so yes it is possible and can be done.

The spec's call for a min 600W PSU. I run a 850W PSU, called EVGA because I am doing the step-up and dumping my 8800GTS KO's 640MB cards for 2 of these 9800GX2's and they told me I should have a minimum of 1000W PSU to run these in SLI.

So if you are talking Tri-SLI, you are probably looking at a 1200w to 1300W and possibly a suplimental running periphals like a Thermaltake 350W that fits in the CD/ROM slot in your chassis, but yes it is possible.

Heat? Yeah, these babies are hot, what do you expect? Hell, my 8800's in SLI idle at 60C +, run Crysis in the mid 70's. I have 5 - 120mm case fans at high most of the time in my Antec P180B, plus the fans on the cards run around 80%. I cna idle them around mid-50's if alll fans are on and ambient temp is around 60F. According to EVGA they say not to worry till they reach mid 90's, so WFE. I was used to my 7950's running mid 30's, but oh well, with power you get heat. If you want to play with power you got to expect it.


I think you are the one who should be doing a little more reading up.
 
Thanks for the obvious asshole!

Any ideas?!

No, my friend, it's you that's mistaken. The special 3-way SLI bridge requires that the cards have two bridge connectors on top. You'll notice the 9800GX2 only has one connector on top, which means it cannot do more than Quad-SLI. Sorry.

Also, those temps aren't anything to worry about. The 8800GT can run at 110°C just fine, and it's the same core.



If the temps shown are what the cards are at,just after gaming or during,then no,thats tolerable ! My eVGA GTS 640 with a heavy oc ran hotter for near a year with no issues
at all.
 
Hi, Bob. I know Nvidia did not intend use of more than 2 GX2 in a system since each has one SLI bridge connection. You are confused if you read my post in responce to likewhoa's and thought I was saying it was possible. Either way, have a good day Bob.
Well, you quoted my post asserting that some were confused and that three GX2s would not work. Then you merely said: "haven't you seen likewhoa's post?" So, exactly how was I to interpret it? I guess now, in hindsight, you were trying to be funny. This clearly went over my head since I have this silly habit of not seeing humor in posts that aren't funny. :D
 
So who is going to be the first person to take theirs apart to redo the thermal compound on the GPUs. I'll be shipping my GTS's off today, -maybe- just maybe, the stars will align and i'll get my gx2's back before the weekend *crosses fingers* But i'm not going to hold my breath.
 
Thanks for the obvious asshole!

Any ideas?!


Kinda harsh don't you think? I was just being a bit sarcastic.

Obviously you mentioned it being so high, which I did read. I did not mean to come off as an asshole. Similarly, I am extremely positive that you did not mean to be too sensitive.
 
Kinda harsh don't you think? I was just being a bit sarcastic.

Obviously you mentioned it being so high, which I did read. I did not mean to come off as an asshole. Similarly, I am extremely positive that you did not mean to be too sensitive.

For sure, Im sorry. Just seeing 1200 dollars that hot pissed me off/ Also it seems the fans dont come on until this thing is on fire, i changed then to 100% all the time @60-65C
 
Temperatures:
Motherboard 52 °C (126 °F)
CPU 50 °C (122 °F)
CPU #1 / Core #1 66 °C (151 °F)
CPU #1 / Core #2 66 °C (151 °F)
CPU #1 / Core #3 43 °C (109 °F)
CPU #1 / Core #4 46 °C (115 °F)
MCP 75 °C (167 °F)
GPU1: GPU 61 °C (142 °F)
GPU2: GPU 54 °C (129 °F)
GPU2: GPU Diode 57 °C (135 °F)
GPU2: GPU Memory 53 °C (127 °F)
GPU2: GPU Ambient 53 °C (127 °F)
GPU2: GPU VRM 56 °C (133 °F)
GPU3: GPU 61 °C (142 °F)
GPU4: GPU 56 °C (133 °F)
GPU4: GPU Diode 59 °C (138 °F)
GPU4: GPU Memory 56 °C (133 °F)
GPU4: GPU Ambient 55 °C (131 °F)
GPU4: GPU VRM 53 °C (127 °F)

Cooling Fans:
CPU 1918 RPM
Chassis 1834 RPM
Chassis #2 6081 RPM
GPU2 1456 RPM (100%)
GPU4 1499 RPM (100%)

Voltage Values:
CPU Core 1.31 V
+3.3 V 3.26 V
+5 V 4.99 V
+12 V 12.09 V
+5 V Standby 4.95 V
VBAT Battery 3.09 V
3.3V Dual 3.26 V
FSB VTT 1.30 V
DIMM 2.12 V
GPU2: GPU Vcc 3.32 V
GPU4: GPU Vcc 3.32 V
Debug Info F FF 58 6F 5C FF
Debug Info T 15 50 52
Debug Info V A4 D5 CC CC A2 C3 E5 (01)
 
Well, you quoted my post asserting that some were confused and that three GX2s would not work. Then you merely said: "haven't you seen likewhoa's post?" So, exactly how was I to interpret it? I guess now, in hindsight, you were trying to be funny. This clearly went over my head since I have this silly habit of not seeing humor in posts that aren't funny. :D
I guess a lack of humor coincides with missing posts for you. You were confused who thought a 3rd GX2 could be used in a system. If you had bothered to read the post above mine it would have been clear who my corrective post was directed at.

Doubt my intent? Do a search on how many posts I've clearly stated only the GTX/Ultra are capable of TRi-SLI. By the way, don't give up your day job yet. I'd suggest practice on your stand up routine.
 
Can you guys have your bitch-fest in another thread. this is about dual GX2's
 
Didn't intend to derail your thread. A simple post correcting the GX2's use got turned into a "I know more than you do" ....:p
On topic, have you found a leaked version to enable quad SLI on the GX2s or waiting until tomorrow's release?
 
I decided to go ahead and install my second 9800GX2 tonight. I have enabled Quad-SLI but I haven't used it yet.

I've got some other comments on these things. First off, I don't like the fact that only one of the DVI ports will work when the system first boots. There is documentation with the card verifying this. Sure enough, the top port won't work outside of Windows. Another thing I don't like is probably specific to the EVGA branded cards. There is the protective film on the graphics (stickers) on the cards. However the stupid part is that they put their warranty sticker on the protective film and not under it or on another part of the card. That's not a good way to do things.

Otherwise I like the card(s) so far.
 
Saw posts about the EVGA sticker. It doesn't make sense why they chose to mount it there. :confused:

Are you waiting for more time where you can have a lengthy gaming session to try quad out? Or waiting to see if Nvidia releases "offical" quad drivers for the GX2s tomorrow?
 
I decided to go ahead and install my second 9800GX2 tonight. I have enabled Quad-SLI but I haven't used it yet.

I've got some other comments on these things. First off, I don't like the fact that only one of the DVI ports will work when the system first boots. There is documentation with the card verifying this. Sure enough, the top port won't work outside of Windows. Another thing I don't like is probably specific to the EVGA branded cards. There is the protective film on the graphics (stickers) on the cards. However the stupid part is that they put their warranty sticker on the protective film and not under it or on another part of the card. That's not a good way to do things.

Otherwise I like the card(s) so far.

yea noticed that too, alot of people are gonna probably forget to cut it off and stick it on the card itself somewhere or just leave it inside the box, but I can see were alot of folks will just void their warranty from not doing either and that's gonna hurt EVGA on returns since customers are gonna freak when they find out later on when doing RMAs. I hope later revisions of the card will have this sticker on the cards itself and somewhere were it's not gonna fall right off after use like some of their older cards i.e 7950X2.
 
Here's EVGA's post about the sticker:
Hi all,

Just to let you know EVGA is aware of this, and the warranty is still valid even when the serial number is removed, as long as the product is registered.

There is a serial number on the back of the box, and on the film itself. We are now also adding a serial number on the bottomside of the heatsink.

Thanks,
Joe Darwin
 
Those crysis, right? Good god someone finally able to play that game maxed.

Dan, you gonna re-install the OS?

WIshful thinking.

and quad sli - didn nvidia go with tri-SLI because of limitation of only being able to process or something 3 frames ahead? why sli above 4 doesnt scale great...
 
That's a limitation with DX9, 3 frames. DX10 can do 4. Or something like that.

It's Tuesday morning now, and still no quad SLi drivers or reviews :(
 
Saw posts about the EVGA sticker. It doesn't make sense why they chose to mount it there. :confused:

Are you waiting for more time where you can have a lengthy gaming session to try quad out? Or waiting to see if Nvidia releases "offical" quad drivers for the GX2s tomorrow?

yea noticed that too, alot of people are gonna probably forget to cut it off and stick it on the card itself somewhere or just leave it inside the box, but I can see were alot of folks will just void their warranty from not doing either and that's gonna hurt EVGA on returns since customers are gonna freak when they find out later on when doing RMAs. I hope later revisions of the card will have this sticker on the cards itself and somewhere were it's not gonna fall right off after use like some of their older cards i.e 7950X2.

I was able to nicely peel my stickers off the film and place them back on the heatsink. I am worried though that they might peel off from the heat like they did on my 8800GTX's.
 
I was able to nicely peel my stickers off the film and place them back on the heatsink. I am worried though that they might peel off from the heat like they did on my 8800GTX's.

yea that's what alot of people that will notice the warranty stickers will probably do, I for one will just keep them in the plastic and inside the box or put away, also EVGA should realize that alot of users don't register their cards nor even notice or even bother to know that the actual warranty sticker is not on the card, but seeing that EVGA will be putting them under the heatsink which is kind of weird seeing the heatsink gets hot and heat will surely make them peels off, anyways I hope they put them on a part that won't easily come off over time.

@Airmanv How's it going man? anymore benchmarks? Have you taken those bad boy apart and reapply some better thermal paste? I know you don't like 3dmark but can you run AquaMark benchmark?
 
Didn't intend to derail your thread. A simple post correcting the GX2's use got turned into a "I know more than you do" ....:p
On topic, have you found a leaked version to enable quad SLI on the GX2s or waiting until tomorrow's release?
Oddly, my post too was intended to correct someone (not you) who thought GX2s would work as a trio. For some reason you felt the need to quote me and then direct me to a quote by the very person I was correcting and then ask if I'd seen it. I'm still not sure why you think this was funny. But it is indeed clear that you did not think GX2s would work as a trio.

My apologies for not looking through your entire post history at that point and figuring out that you were trying to be funny.

That's the last I'll say on this. Sorry for my part in the derailment.

Edit: I think I just figured out where all this started. You may have assumed that I was addressing you when I made my initial post regarding GX2s not working as a trio. You apparently did this because my post appears below yours. Yet, I was not addressing your post. I admit that this may have been unclear because I had tried not to single anyone out via quoting (though I had likewhoa --whose post appears immediately above yours-- in mind). I think you might have thought I was correcting you, so you quoted me back to me, then quoted likewhoa, and asked if I'd seen it. Then, not realizing who you were or that you had posted prior in the thread, I interpreted that post as someone saying: "But this guy says it would work!". . . which I interpreted as very odd (as I described) considering he was the very person that was being corrected/informed. And from there, we were off to the races. So, it's all just a silly misunderstanding. And I apologize for my part in it and the thread derailment.
 
Well, from the recent review, I think its safe to say that while on Crysis, the Quads beat out a tri-8800GTX setup by what... 3fps? But on Cod4, It seems the triple GTX's would stomp on the Quad setup. Too bad they didnt open up that memory bandwidth a little more, or use a little more RAM.
 
All this talk makes me wish EVGA would get my 2 - 9800GX2's shipped to me, damn this is killing me. I am sitting here limping by with a single BFG 7950GT OC because I just shipped back my both my 8800GTS KO's (640MB) in their Step-up Program ...........Wow, cant wait, keep the info coming, I just read everything I can find on these cards, I have become obsessed it seems.

I just want to know will the climax be worth it?

I am seriously waiting to see what kinds of bench scores (Crysis or 3DMARK06) someone gets with an EVGA 780i board, dual 98000GX2's and 2GB of PC800 with atleast a E6600 CPU - anyone? Anyone have real world data on that?
 
I think you may be Right, An awfull lot of people have had RAID problems and Nvidia Boards. I do Think that a Super Extended ATX Spec should be a cure, as it could stretch out some of those issues, and allow for Cooler Wire Traces. Maybe you could drop a suggestion into some of these MFRs Ears when you see them next! But then again, we would all need some New Caseage, to put it in! Grinning profusely!
 
^^^^^ Make sure you have positive air pressure in your case, if you have negative air pressure (more cfm going out than in) air will try to go in through the back of the GX2, effectively stalling the airflow inside the coolers. One way to check is with a thin strip of tissue paper, check all of the holes in the case and the gpu exhausts.

I currently use a 120mm (65 CFM) front fan, 120mm (46 CFM) side fan, two 80mm (28 CFM) for rear and top fans, and a PSU with variable 120mm fan. Running the fans at 75-80% RPM with paper filters (probably another 10% loss in CFM for the two intake fans) and I have a moderate amount of negative air pressure. I now estimate that my PSU is around 35-45 CFM. Around a total of 15 CFM more going out than in. I just bought two 8800GTS's, so I expect up to another 20CFM for each going out. Bought two new 120mm fans (79 CFM) to replace my existing ones to account for this and put me back into positive pressure.
 
and that good sirs is why i decided to stick with my simple single 8800 GTS (G92) Quiet + no toasty. But that could help if you wanted a nice breakfast!
 
Yeah that's much much better a 50C difference :)

Edit: ...look at his GPU temps, not the cpu temps.
 
you're confusing degrees C and F

the temperature is pretty much the same. slightly lower.
 
Back
Top