Gigabyte colour SATA ports

RockSolid

Weaksauce
Joined
Jan 20, 2008
Messages
125
I have just changed over my HD and put in a WD 500GB SATA HDD, but I want to add another WD 320GB SATA HDD has a backup but on my MB "GA N680SLI-DQ6" there are four Purple GSATA ports and 6 yellow SATAII ports but I don't want to use both HDD in RAID so what ports do I use Yellow or Purple?

I am using the Purple port for "GSATAII 0" for WD 500GB and "GSATAII 1" for the DVD burner. I read somewhere if I use it this way I lose the Performance of the WD. @3gb/s because it shares the two ports when burning or downloading or should I move it to "GSATAII 3" port for the DVD burner so it don't share...

Or put the DVD burner on the Yellow SATAII 0 port with the 320GB on SATAII 1 port

I just find on the back of a SATA Drive there is a white plug do it mean it can be a slave?

Can you answer these problems!!!!

Thank You for your time.
 
The ports are used in whatever mode you set them as in the BIOS, in terms of RAID, AHCI, or IDE. On my one Gigabyte board, the purple ports were some JMicron crap, and the yellow ports were on the Intel controller, so I avoided the purple ports completely. Take a look in your manual to see what controller is what color, and stick to the Intel ones.

As for the drives, SATA doesn't "share" anything across ports, so your performance is fine. SATA drives also don't have master or slave settings (no point, since only one drive per port can be used).
 
Hi DeaconFrost

I was told the JMicron is faster than the Intel ICH8 on the Gigabyte MB, JMicron supports AHCI & NCQ but Intel ICH8 dose not

I was going to use it this way:

GSATAII 0 WD 500GB

GSATAII 1 ----------------

GSATAII 3 DVD Burner

GSATAII 4 WD 320GB backup

All on the Purple slots but if I use it this way I have two HHDs and I don't want to use it in RAID is there away I can not have my HDD drives in RAID when bootup

But after reading what you said what if I put it in this way:

SATAII 0 WD 500GB

SATAII 1 --------------

SATAII 2 DVD Burner

SATAII 3 --------------

SATAII 4 WD 320GB

will it work? but because I setup my WD on GSATA and install my Viista do I need to re-install Vista again because I change from the JMicron GSATA to Intel SATA??

I can't read my GA book because it all in chinese as I live here. I tried to download the mannal from Gigabyte website but it don't open and the net fails when downloading big problem for me.
 
The Intel chipset supports AHCI (should, does on other Gigabyte boards) and NCQ is useless on a desktop, so it isn't even worth considering. JMicron controllers are junk, and if you load the driver from Windows Update, you'll be doing a fresh install soon after. Avoid them and stick to the Intel chipset controllers.

I can't comment much on the manual, but the three Gigabyte boards I've used recently have had the manuals in multiple languages.
 
Thank you for your reply "DeaconFrost"

Ok one more question if I un-plug the WD HDD from the GSATA and plug it into the intel SATAII 0 will it work when it boots up? or do I have to re-install vista again...

"Gigabyte boards I've used recently have had the manuals in multiple languages" yes mine had the same in the UK but I am in china and it don't have it.
 
I'm not sure if it would work or not. I know you'd probably want to load the Intel chipset drivers first, before moving it. Vista is supposed to be much better at detecting changes like this and still booting.
 
Hi DeaconFrost

I was told the JMicron is faster than the Intel ICH8 on the Gigabyte MB, JMicron supports AHCI & NCQ but Intel ICH8 dose not.

I'm confused here. How can your nVidia nForce 680i board use an Intel ICH south bridge?
 
I missed that as well. I glanced over it quickly, saw the DQ6 and thought it was the Intel board. In that case, my advice might not be valid, but I'd still avoid anything from JMicron if it exists on your board.
 
The gigabyte ports are controlled by the JMicron controller. I'm not sure if they're worse than the nForce controller, lol. You may have problems with the NVIDIA drivers and those ports, but if they work for you, great! If you're not doing any hot-swapping, set them all to IDE mode if you experience any problems in AHCI mode. Just don't enable RAID, and none of the drives will be in RAID - simple as that. You can put any drive on any port you want... order does not matter unless you want to avoid one of the controllers.
 
The only issue I've seen in the past (with mine and others) is that if you use an IDE device on the JMicron controller, do not use SATA on that controller; keep the SATA devices on the other controller. If you have no IDE devices, you shouldn't have any big problem. I don't know about relative performance.
 
Hi Michael Daly

I don't have any IDE in my computer they are all SATA even the DVD Burner

@enginurd

So what you are saying is if I had two HDD on the purple sots but don't enable RAID in BIOS it will work?.

@DeaconFrost
It's not a Intel board it's a Gigabyte.

What I really want to know is I wanted to use the purple slot GSATAII 0 WD 500 and GSATAII 3 for DVD Burner because I read this: "The purple ports along the bottom edge come by way of a pair of individual controllers and arrays can't be built across them; individually they do support two-drive RAID"

Because the GSATAII 0 & GSATAII 1, is one pair and the GSATAII 3 & GSATAII 4, is another pair. I didn't want to use the WD 500 & DVD Burner on one pair of controller because of the shared performance and I wanted to use the other pair of controller GSATAII 3 for DVD. so they don't share And I wanted to use one yellow port SATAII 0 for the WD 320 HDD

Will it work this way?

I read someone post he said this:
"I switched to the Gigabyte onboard SATA2 port and I finally managed to get it read/write 20 times faster than using the Intel ICH8 port!!!It was 3.x MB/s using the ICH8, but now it goes up to 7x MB/s using the Gigabyte port without installing any driver~!!"

I also read this: "NCQ is designed to improve performance and reliability as the transactional workload increases - When your application sends multiple commands to your drive, your drive can optimize the completion of these commands to reduce mechanical workload and improve performance"

Gigabyte:
In terms of storage support, the nForce 680i SLI's six SATA 3.0Gbps ports are supplemented further by two extra Gigabyte SATA2, (JMicron) controllers offering four additional RAID capable SATA 3.0Gbps ports with AHCI and NCQ support. This pumps the total storage capacity of the board to a maximum of ten SATA.
 
@DeaconFrost
It's not a Intel board it's a Gigabyte.
Gigabyte is the brand of motherboard. When I said Intel, that's referring to the chipset of the board. However, instead of an Intel board, you have an Nvidia board.
 
Back
Top