OMG PCIE x16@x4 help

Joined
Oct 16, 2007
Messages
634
Ok recently did a GPU Z and noticed that my bus width is at x4 instead of x16. I was shocked. I looked at my motherboard manual and noticed that its suppose to be like this. What I need to know in the next couple hours before I place my order to the egg. I need to know if this is really affecting my performance??? Will goin to a board with full x16 give me better performance??
 
The rest of your system specs would be very helpful. Like, what kind of video card and processor.
 
The rest of your system specs would be very helpful. Like, what kind of video card and processor.

Yea, seriously. Plus bus width varies upon your PCI-e slot, it was very stupid of you going SLI in the first place prior to doing such research. Motherboard model would help a ton.
 
Yeah, there is probably a major performance hit then with that video card. That board can run PCI-E X16, so check your BIOS and make sure it's setup properly.
 
its set to auto in the bios. but does let u set mhz which start at 90. i have no idea what the numbers mean. if i could get a better grasp of what they mean maybe i could figure it out.
 
This really depends on what your gaming resolution is.

What do you tend to play at?

PCI-E 4x is 1000MB/s in each direction (2000MB/s total)

Really, this is about the equivalent to AGP 4x 1000MB/s download, 66MB/s upload.

AGP 8x is 2000MB/s download, 133MB/s upload.

Really, if you are gaming at 1280x1024 and below, it is likely that you would not see too much of a performance hit. However, if you game at 1600x1200 or above, you will notice a big difference.

At the lowest, I would run it at PCI-E 8x, just to be safe (which I have done, but with lower end cards, i.e. 6600LE and 8500GT).
 
I game at 1600x1200 at home and 1440 x 900 at lans and such. Maybe i should play around with those numbers that are in the bios but i really dont feel comfortable doin that since i have no idea what they mean.
 
Good article, but I still wouldn't go below 8x if you can help it.

I think this is why they haven't made any PCI-E 4x or 8x video cards.

The cards that are 1x are mostly low form factor or are designed for a business environment like servers where there may not be a PCI-E 16x slot or if it is in use. They aren't really designed for gaming.

Even though these cards are capable of running at such low port speeds, it is more for compatibility (which I like) more than it is anything else.
 
Wait, are you certain you're using the right PCIe slot? Take a look at the specs on the page you linked: your board has one x16 slot and an x4 slot with a universal connector.

One slot is blue and is a full-length PCIe x16 slot. The other slot is orange and is a x4 slot designed to accept any length of card (even x16 cards). You want to use the blue slot that is full-length if you only have one video card. If you use the orange slot, the bus speed will default to only x4, with no way to raise it.

The orange universal slot is only intended for people who need to run a second video card to handle more than two monitors. Do not use it for a gaming card.

ALSO: GPU-Z is new and still pretty buggy. If you actually have your graphics card in the correct slot (the blue full-length slot), I would suggest you get a second opinion.

If you want a second opinion on your link width, download CPU-Z and run it. Look under the Mainboard tab, and look for Graphic Interface. I would much more readily trust CPU-Z than the brand-new GPU-Z.
 
Yeah cou-z said link width x4 then it says max supported x16.

Now, more than ever, I'm convinced you have the card in the wrong slot. If you don't have it in thew full-length slot (blue), you cannot run the card above x4 mode.

LET ME MAKE THIS CLEAR: you have TWO slots on your motherboard that can accept a PCIe x16 graphics card. One is significantly shorter than the other, and is orange, and will only run your card at x4. The other is longer and blue colored, and will run your card at full x16. You want to be absolutely certain the longer blue slot is the one you are using.

If I'm wrong, and you have it in the right slot, then unfortunately there's nothing we can do for you, because there is no setting anywhere in your motherboard's manual to enable wider bus settings.
 
Now, more than ever, I'm convinced you have the card in the wrong slot. If you don't have it in thew full-length slot (blue), you cannot run the card above x4 mode.

LET ME MAKE THIS CLEAR: you have TWO slots on your motherboard that can accept a PCIe x16 graphics card. One is significantly shorter than the other, and is orange, and will only run your card at x4. The other is longer and blue colored, and will run your card at full x16. You want to be absolutely certain the longer blue slot is the one you are using.

If I'm wrong, and you have it in the right slot, then unfortunately there's nothing we can do for you, because there is no setting anywhere in your motherboard's manual to enable wider bus settings.

LOL

Well said. It's like explaining something to a child, you have to go slow and simple.

If he really does have it in the universal slot, I am going to LMAO.

:D

Looking at the pics on newegg made me think: would he put it in the bottom slot? Naa... couldn't be. But, it might be... :eek:

BTW, that's a very colorful mobo you have there.
 
I have only 3 slots of which 2 are pci.So im about as sure that I have it in the right slot as im sure the sun will rise tomrow.
 
I have only 3 slots of which 2 are pci.So im about as sure that I have it in the right slot as im sure the sun will rise tomrow.

The one you linked to on newegg has four slots though. Is this not your mobo?

If it's not the exact same, could you post a pic of your mobo?
 
Ok, you might want to flash your BIOS. It might give you a new option or fix an existing one that is making your slot go to 4x instead of 16x.

http://www.gigabyte-usa.com/Support/Motherboard/BIOS_Model.aspx?ProductID=2562

I am really suprised that this board would not support 16x. I know it does, it HAS too. If not, that is one shitty board. Keep posting and I will get back to you.


I just read on the site that it does infact support PCI-E 16x. I wonder if your onboard video is interfering with the PCI-E slot. Try disabling (if you haven't already) the onboard video. This might fix the problem if the onboard is "sharing" some of the PCI-E lanes. It should also give you some of your system memory's bandwidth back.
 
Look at the bottom of page 11 of your manual:
(The block diagram on page 8 also says the same thing)

Note 1: The GA-945GZM-S2 supports up to PCI Express x4 mode.

Really sorry to say your stuck at 4x with that motherboard. GPU-z is correct.
 
Look at the bottom of page 11 of your manual:
(The block diagram on page 8 also says the same thing)

Note 1: The GA-945GZM-S2 supports up to PCI Express x4 mode.

Really sorry to say your stuck at 4x with that motherboard. GPU-z is correct.

Yeah, even just scroll down on the linked page to the motherboard

Expansion Slots: 1 PCI Express x 16 slot (@x4)

You're SOL with that one.
 
Yup, the manufacturer cut down on the number of PCIe links to save money. This is, for good or bad, easily done with the PCIe standard: it allows manufacturers to offer a second video card slot with reduced 3D capabilities, or as in this case, allows manufacturers to deliver a cut-price board with some minimal upgradability. Hey, x4 PCIe is still better than regular PCI, so you can hardly complain about x4 speed on an entry-level board - a few years ago, an integrated video board would have nothing but PCI slots.

I figured it was a physical limitation, I have NEVER heard of a PCIe card default to a slower speed in a full x16 slot. Well, the solution is easy if you ask me - that motherboard you were eying: BUY IT.

And next time, PLEASE give your correct system specs. I could have solved your problem in 5 seconds with the correct model number, the x16 slot in x4 mode is noted plainly on Gigabyte's site.
 
Im just so angry right now that i didnt see that when i bought the board. Just so angry cause when i bought this board gigabyte only made this board and another at the time. I will have to sell somethin to get a new board. I just bought some Beyer DT-770's for about 182 bucks.
 
Im just so angry right now that i didnt see that when i bought the board. Just so angry cause when i bought this board gigabyte only made this board and another at the time. I will have to sell somethin to get a new board. I just bought some Beyer DT-770's for about 182 bucks.

Well, for now it's not critical. You can still get playable framerates from the card, you'll just have to take a resolution hit for now.
 
You have to be really careful with purchasing mATX boards (recent ones) if you're going to upgrade to a stand alone video cards with performance in mind because there are quite a few that don't support a full 16x bandwidth with PCIe. You have to read the specs carefully.
 
how much is he actually losing at X4 though? I mean aren't we still nowhere near fully using an X8? I think your fine I don't even know if an 8800GT would hinder that much would it?

my M2NSLi is SLi 16x/16x and every comparison i've seen so far between a 16x and 8X they are dead even with little to know difference what-so-ever, but I dont know the same about 4x, I just can't imagine it ruining your experience A whole lot. I pretty much just wanted a 16x/16x SLi board (earlier ones were 8x/8x I think) and the only real reason for a 16x board right now is just because of the name, I'd say you're probably just fine



edit~
Wow after reading that article at Toms that's insain, definatly get A new board if thats the case sorry D=
 
Yeah I am real soon. Prolly will order next thursday depending on how my paycheck looks and bills shake out.
 
Back
Top