DVI-I DUAL LINK to HDMI possible?

BJH088

Gawd
Joined
Apr 3, 2007
Messages
536
Is it possible to go from DVI-I (Dual Link) to HDMI.

Specifically looking for a DVI-I Dual link male to HDMI female adaptor... anybody?
 
I presume you mean DL-DVI to DL-HDMI, not DL-DVI to SL-HDMI.

Although there is a specification for a Type B HDMI connector that is dual link (23 pin), I have never seen it implemented. If you google for DL-HDMI you may find some products described as DL, but on closer inspection every single one I've looked at turns out to be DL-DVI>SL-HDMI (19 pin Type A).
 
didnt know their were dual link and singal link hdmi.

but their is DVI-D Dual Link and DVI-I Dual Link

im lookin for DVI-I Dual link to HDMI whatever for my ps3
 
so a DVI-D dual link will plug into an DVI-I input are you saying without the extra pins needed
 
Hi,

How did you solve this?
Because I have a dell 30" LCD and it uses Dual Link DVI cable. And I bought a DVI-D (female) HDMI (male) adaptor. But when I connect my PS3 to my monitor I don't get anything.

Any advice?
 
I have a dell 30" LCD and it uses Dual Link DVI cable. And I bought a DVI-D (female) HDMI (male) adaptor. But when I connect my PS3 to my monitor I don't get anything.

If you set the PS3 to 720p60 it should work.

The Dell has no on-board video processor, so it can't accept any signals other than 1280x800/720p60 and 2560x1600/1440p60.
 
ok, that sounds reasonable.
How do you know this? I thought I knew everything about the monitor before I bought it. Apparently not...

Thanks, will go home during lunch to give it a shot.

Cheers
 
A great place to buy really cheap but good quality cables is www.cablesforless.com.



__________________
New build on the way:
Q6600
eVGA 680i A1
OCZ 2GB DDR2 1066
eVGA 8800GTX
Already have:
X-Fi XtremeMusic
Raptor X - Seagate 320GB PRT
OCZ GameXStream 600W
Thermaltake Shark Full ATX
 
I don't have the option the PS3 to put it on 720p

If I go into HDMI it goes blank right away without giving me any options.
But if I choose the option Component/D-Terminal which is the 2nd option I can choose:

Standard NTSC
480p
720p
1080i
1080p

I click on 720p and it goes blank. I switch to my other monitor and don't see anything. So I wait 30 seconds and connect my smaller monitor again to see the options again.

I went through most of the options but can't see anything on the Dell 30".

:(
 
I have firmware 1.90
I downloaded and installed it yesterday after multiple attemps of hooking my monitor up. After the installation of the new firmware I did the whole thing again, but no success... :(
 
Ajax9000: Are you sure the monitor will accept 1280x720 (720p)? I thought it would only accept 2560x1600 or 1280x800, and that any other resoultion (including 1280x720) would have to be scaled by the graphics card. If I read your post right you're saying it will accept 4 resolutions: 2560x1600, 2560x1440. 1280x800 and 1280x720.
 
Ajax9000: Are you sure the monitor will accept 1280x720 (720p)? I thought it would only accept 2560x1600 or 1280x800, and that any other resoultion (including 1280x720) would have to be scaled by the graphics card. If I read your post right you're saying it will accept 4 resolutions: 2560x1600, 2560x1440. 1280x800 and 1280x720.

I actually only supports two native resolutions. I don't think I said the above. Maybe someone else did.
So if I understand correctly, I will not be able to run my PS3 on my kick ass monitor?

Any ways arround? Can I hook it up to my graphic card or some kind of box to make it work?
 
Correct. The 3007WFP-HC will only do two resolutions -
DVI Dual-Link port = 2560x1600 60hz HDCP
DVI Single-Link port = 1280x800 60hz
 
Oops, my bad. I was thinking of the way a PC graphics card can "emulate" 1280x720 by padding 40 black lines above and below the image -- which of course makes it 1280x800 being sent to the monitor. (Like the PowerStrip resolution-in-a-resolution trick.)
 
Back
Top