Swiftech H20-120 Premium

TheGardenTool

2[H]4U
2FA
Joined
Mar 12, 2006
Messages
4,038
Is the Swiftech H20-120 Premium a good kit for somebody water cooling for the first time?

I'm also planning on adding a block to the north bridge but I'm trying to find some more information on what fits my motherboard.
 
It's not bad at all. Probably one of the better lower end kits out there. I had one and didn't like it only because the rad was a bit too big for me and it wasn't AM2. Didn't want to go through the hassle of changing faceplates and so on.

Is it better to buy individual? Yes? Is it more hassle? Just a bit more. If you buy used and cheap go for it!

If you buy new you really don't need a res. Use a T-Line and if you can get a dual rad and try and find a decent block. Apogee isn't bad.

Don't waste $ on a NB block. There are good passive solution and good active solutions.
 
Its a decent kit to start with if u only want to watercool ur CPU , Apogee GT is a good block, specially for the price . You can get it for around $ 169. If u buy individually u gonna need to spend a little more . Like the poster before said , no need to watercool the NB , just a waste of money if its not for the fancy looking only.;)
 
I would spend a couple extra bucks and get the h20-220 ultra because if your just starting out thats means you probably going to be cooling cpu and maybe your gpu after that your loop get complicated I heard. However, I think the 220-ultra provides you with a better upgrade path in the future.

Just my 2 cents
 
Pretty good little kits really, I have both the 120 and 220 versions in my case.............:eek: I'm using the 120 version (with a MCW60) just to cool my video card.............:D
 
Thanks for some useful information thus far.

The reason I want to cool the north bridge is because this motherboard has issues without it being actively cooled. Right now I have the case laying on its side with a old 40mm fan sitting on top of the passive heatsink. And because of how the heatsink is designed, the fan will not mount without some ghetto modding, so I'd still need to buy a good solution. If I'm already going watercooling and need a new solution, doesn't it make since to add it in the loop?

I cannot go with the 220, not only is it about $100 more, I want everything to install clean and internally.

Another thought is, I do have a 80mm exhaust "blow hole" on top that I could slap an 80mm radiator just to cool the CPU and use the 120mm later for graphics, but as of right now, I haven't seen any unusual temperatures from my 8800GTS that would require it to be under water, yet.
 
I have the kit, it's not bad at all. Don't expect to get a HUGE performance gain over air cooling though. When I switched to water (this kit) my temps actually went up by 4C idle, but down a good 7C under load.

In all, if you plan on OCing a bit, this kit will do you justice. You'll need to get a new fan for it (the one it comes with sucks), but overall, water = better for OCing. You'll see some temp increases idling, but man. . . I've gone in 200mhz intervals from 2.4ghz to 3.4, and I never saw my temps (under full load) go above 54C, never.
 
u also have to be careful on measuring temp on sensors. Some use air around them and ho doesn't blow air around so it might be wrong.

Even this kit is better than air.
 
Well I do have a pretty significant overclock on the E4300, but the way it's going I think I can still manage to get to 3.2GHz on something other than stock cooling. I've used a couple different CPU temp programs and each one shows a different temp.

Newegg has this kit for relatively cheap, and I have some credit to use there, so that's why I was wanting to go with a whole kit over piece by piece.
 
u also have to be careful on measuring temp on sensors. Some use air around them and ho doesn't blow air around so it might be wrong.

Even this kit is better than air.

I measure using TAT. The difference between TAT and SpeedFan is 3-4C, but that's fine by my book.
 
no way u could cool CPU and NB with one 80mm rad only :eek:



Its a 120MM rad and I was cooling my overclocked AMD X2 3800 @ 3.0 Ghz with a X1900XTX at max overdrive overclock on that same loop using a maze4. My temps for CPU never broke 40 and the GPU never broke 45 deg c. Just pop a $10 replacement cooler on the chipset, there isn't any reason to water cool NB.

Despite what people say a single rad with a decent fan (~30db / 60 - 70 CFM) can handle quite abit. Moving to my internal Thermochill PA120.2 (Swifty 655 pump, 1/2" tubing) with the same hardware didn't change my temps at all over this kit. So, yes it will do a nice job.
 
OP wrote he will use a 80mm rad to cool CPU and NB and save the 120mm for later . The kit comes with a 120mm rad thats true , and thats indeed enough to keep the CPU at a decent temp. If u want to cool the CPU and a nvidia 8800 u definitly need a 240mm rad or 2 x120mm for some good temp at low noiselevel.
 
Well I did go ahead and order this kit along with the MCW30 chipset block. I should have it Friday.

I never said for certain that I'd use a 80mm radiator; I was just wondering if it would have had the juice for a CPU and NB with a 120mm radiator afterwards for the 8800GTS. As of right now, I have no short-term plan of watercooling the GPU.

I am not disappointed with the noise level from anything in the system other than the horrid 40mm ghetto-rigged fan on the NB to keep the BSODs away. If you are considering purchasing the abit Fatal1ty FP-IN9 SLI, be sure to buy a better active cooling solution for the NB. :( This is the only reason I want to put the NB under water.

The fan on the radiator is going to be replaced by a Scythe S-FLEX SFF21F, rated at 28dBA/1600RPM/63.7CFM

I'm not looking for super quiet, rather than lower temp under load.
 
Just FYI, 2 low-rpm fans in push/pull config work just as effectively as a single higher-rpm fan, if not more so. And most importantly, more quietly! This holds true for the BIP rad which came with my Swiftech kit anyway.
 
Back
Top