Overclocking with giel ddr-400

Rothius

Limp Gawd
Joined
Aug 6, 2006
Messages
201
So ive recently ordered 4gb of geil ram to replace my 4x512 corsair ram. The Geil ram is 4x1gb sticks and is rated at 2.5-3-3-6 at ddr-400 where as my current corsair xms ram is rated at 3-3-3-8 at ddr-400 but i run my current ram at ddr-333 because of my overclock and it gives 2.5-3-3-7 timings and almost goes back upto 400 speed. My question is... has any1 had much luck with overclocking geil ram will i need to run it at 333 like my current corsair ram or will i be able to run it at 400 and keep my oc? (maybe need to over volt it or something?)
 
You'll probably have to run it at the same settings. I'm sorry :(. 4gig is a lot of memory for your cpu's memory controller to take care of. You might get lucky, but I really don't think it's gonna happen. GL though.
 
I thought the size of the memory wasnt that important , just how many chips u used, i know when u use 4x512 u get t2 draw backs. But has any1 used giel for overclocking before?
 
Well i get it tomorrow and ill let ya's know how 4 sticks of it go :p.
 
IIRC, with 4 memory slots populated on AMD platform you are limited to 333mhz... although I think it was fixed after venice or something :D Try searching in AMD forum ;)
 
Yeah the older amd cores was ment to be out of luck when using 4 sticks but apprently after newer san digeo cores like the 3700+'s / fx etc 4 sticks should be able to run at 400. When they get to my door ill give it ago.
 
Hopefully your board is rated for 4sticks at DDR400. Some boards default to 333 with 4 sticks.
 
Hmm didnt know the board could affect that i thought it was just the memory controller on the cpu and the memory it self.. any1 know how the asus A8N-E goes? uses a nforce 4 chipset im pretty sure.
 
My old MSI neo4 board didn't support DDR400 with 4 sticks. My DFI does. Go to ASUS's website, look up your board and see. Hopefully it will.
 
my a8n5x supports 4x256 @400mhz but 2t only,ran it that way for 6 months,before i got 2x512,btw the a8n5x is basically the same board but with plain nforce 4,i believe thea8n-e is the ultra
 
Well i just set my current 4x512 to 400 and it seems to be going fine... just had to loosen the timings abit.
 
Just been running some stress tests like prime95 and my ram seems to be holding fine... its sitting at 460mhz ddr 3-3-3-8 timing... i hope my new ram can match this or stay close to it. In vista my ram outscores my cpu now lol.
 
Had to drop a .1ghz of my overclock but i got the giel running at 450mhz , 4x1gb sticks 3-3-3-7 2t stock volt. The bank cycle time is 12 from my last ram and dram idle time is 16 clocks... should i lower these or just leave it?
 
Had to drop a .1ghz of my overclock but i got the giel running at 450mhz , 4x1gb sticks 3-3-3-7 2t stock volt. The bank cycle time is 12 from my last ram and dram idle time is 16 clocks... should i lower these or just leave it?

I'd try to lower them. Good job btw!
 
So whats a good bank cycle to have? ive never touched it before and dont wanna lower so much it wont boot lol is 10 or 11 decent?
 
not sure about Geil.. or 1Gb sticks.... but I have my Corsair Value Select DDR400(2x512)

running at DDR560 (280Mhz) at Cas3... normal was 2.5.

I want to get another Gb of the same since it clocks so well.

The last Geil Ram I encountered.. I wasn't impressed with.... haven't used it since.
 
Ive set it to 10 , seems to be running fine

Good, I'd probably leave it at 10. Also I suggest that you try a 1T command rate.

not sure about Geil.. or 1Gb sticks.... but I have my Corsair Value Select DDR400(2x512)

running at DDR560 (280Mhz) at Cas3... normal was 2.5.

I want to get another Gb of the same since it clocks so well.

The last Geil Ram I encountered.. I wasn't impressed with.... haven't used it since.

Wow nice OC on "value" ram.
 
Dont think i can get 1t coz im using 4x1gb... so i need to keep 2t wouldnt i?
 
Back
Top