Undervolting Q6600

The Tuniq comes with a potentiometer to vary fan speed. I'm assuming you've turned it up to max and still get hi 40's.

I have many questions:

* What is the ambient temp?
* Is your case opened or closed?
* Are you using the tri-speed fans that came with your case? If so what are their settings (lo/med/hi)?
* Did you mount an intake fan?

Lets rule out air flow, get a room fan and direct its flow into your open case. If you don't have an room fan make a duct from cardboard that goes from your HSF directly to your exhaust fans. It need only cover two sides, top of HSF and side nearest video card. Turn your fans to max, leave case open, and check temps.

If you're temps are unchanged then I believe you're not making good contact between the IHS and HSF. This is entirely possible with a lapped HSF, especially if flat. My IHS was slightly concave - matter of fact it would have been a good match for the convex TRUE base. I lapped both.
 
i got the samething about the voltage,but when a check cpu-z,they said a got a 1,6ghz ??:confused: and a got prob whit the memory remap!!
 
i got the samething about the voltage,but when a check cpu-z,they said a got a 1,6ghz ??:confused: and a got prob whit the memory remap!!

I'm not exactly sure what you're saying. Intel CPUs will drop their multiplier when not loaded. You can control this via BIOS. That's most likely why you're seeing 1.6ghz, 266mhz x 6.
 
Check your clip that holds your CPU in place.

Is it bent from multiple remountings?

If it is, it might be preventing a good thermal connection between the HS and the IHS.

if it's bent, remove it, and mount your HS directly over the CPU. to hold it in place.
 
Hey all, sorry for the long response time, I was in the middle of a move.


The Tuniq comes with a potentiometer to vary fan speed. I'm assuming you've turned it up to max and still get hi 40's.

The fan controller that came with the Tuniq 120 is on high. BIOS is set to "Auto," though, which means that fan speed is based on temperature/usage. I have disabled this to force the fan to run at max speed and the temperature differences were minute.

* What is the ambient temp?
* Is your case opened or closed?
* Are you using the tri-speed fans that came with your case? If so what are their settings (lo/med/hi)?
* Did you mount an intake fan?

Ambient temp is under 80ºC. Case is closed. I am using the tri-speed fans that came with the case (one by PSU and 2 top/back ones). The top 2 are on high and the PSU one is on medium. I do not have an intake fan (will eventually get one, though).

Lets rule out air flow, get a room fan and direct its flow into your open case. If you don't have an room fan make a duct from cardboard that goes from your HSF directly to your exhaust fans. It need only cover two sides, top of HSF and side nearest video card. Turn your fans to max, leave case open, and check temps.

If you're temps are unchanged then I believe you're not making good contact between the IHS and HSF. This is entirely possible with a lapped HSF, especially if flat. My IHS was slightly concave - matter of fact it would have been a good match for the convex TRUE base. I lapped both.

I opened the case and temps immediately dropped to low 40's (from high 40's). I directed my small fan (that doesn't really push much air) into the case and saw another few degrees drop in temps.

I am pretty firm that I will not lap my CPU. At this point I cannot risk voiding my warranty. Even without doing so I should still be able to manage much better temps than I currently am.

I don't see how air flow can be bad with how the HSF is blowing straight out back (I checked) right through a 120mm fan that is on high. See here.

Any suggestions as to where I go from here?
 
Ambient temp is under 80ºC. Case is closed. I am using the tri-speed fans that came with the case (one by PSU and 2 top/back ones). The top 2 are on high and the PSU one is on medium. I do not have an intake fan (will eventually get one, though).

I opened the case and temps immediately dropped to low 40's (from high 40's). I directed my small fan (that doesn't really push much air) into the case and saw another few degrees drop in temps.

Any suggestions as to where I go from here?

The temps still seem a bit high compared to the TRUE. The Tuniq may not be as good as the TRUE. I have one sitting here but I've never bothered to test it after seeing favorable results with the TRUE.

At those temps I'd say you have a B3 OC'd to 3ghz, unfortunately you don't. Something is still up. Did you disable power saving settings in BIOS (C1E, EIST, etc...)?

There is some good news, you have an air flow problem that when addressed will lower your temps to low 40s. Add the intake and you'll chop a few C off. You also have good contact between the HSF & IHS.

That's about all I got, since you're not going to lap the IHS I think were done. You could load F5 bios, maybe resetting all power saving options, etc... last ditch effort.
 
I did some cable tidying on my machine and now I'm getting 44/42/38/38 as my temps and I'm still on stock cooling.
 
Back
Top