Rampage Extreme 1, power button does nothing.

Tormenter

n00b
Joined
Feb 4, 2013
Messages
4
Hi all,

I'm experiencing a bit of a problem.

I swapped out my hd 4890 for my new gtx 660 sc and now my computer won't start.

I used to have a water cooled system but the pump stopped working so the unit was useless, I purchased a freezer pro 13 and everything has been fine... this was months ago.

While I was swapping out my card today I decided to remove (rip out) the useless pump, unfortunately I got some fluid, only a small amount of non conducting PC ICE, on the board itself and when I tried to power it all back up my lcd poster kept flashing cpu init and wouldn't power up. very worried I hung a hairdryer over it for about 20 minutes then plugged it back in.. now the poster says welcome, as it should, and the motherboard is lit up as normal, however when I press the power button it doesn't do anything at all, neither does the onboard start button.

As stated the board looks fine, lit up in all the right places, my poster reports properly there just doesn't seem to be a signal sent to tell it to powerup.

It's all a pain in the butt, the gpu is brand new today. :(

Does anyone have any suggestions or am I as screwed as I think I am?.. if I am screwed and need a new mobo.. if I manage to get another rampage extreme 1 will I be able to keep my data.. or will I have to reinstall my OS also?

Please someone have some good news for me. (pleading smile)
 
Unfortunately any amount of liquid in the wrong place can easily short out components. I once accidentally spilled a half cup of water through the top exhaust of my tower and turned everything off immediately. I dried everything out over the course of a couple days before I reassembled. Everything worked except the video card. I recommend you do not try and turn it on anymore until you're completely sure that everything is dry. Wet components should never be powered on as that is when the damage occurs.

So basically, it may be in your best interest to disassemble everything and thoroughly dry everything out. Then start piecing it back together slowly so you can test out each of the components one by one. It would be a great help if you had another machine or could use a friend's to help you test out your pieces. Good luck.
 
Unfortunately I don't have any spares, or know anyone with.

ok, it's just a waiting game then to see if it 'dries' out... what about my other question, any idea there? Can I keep my existing OS if I find another of the same board? Does it work that way?

thx.
 
Last edited:
Did you check to make sure that the connector for the power button is still installed? Could you have pulled it off removing the pump? If the onboard power button doesn't work, you can try shorting together the power switch terminals with a small screwdriver or jumper to see if that works.

As far as the OS is concerned, it's a wash as far as having to reinstall.

I recently upgraded my wife's PC with all my old parts (P/S, mobo, CPU, RAM, video card) and her existing W7 install just needed to be re-activated. She doesn't care about performance and the like so I've left it be.

I always reinstall the OS after a mobo and/or CPU swap.
 
Really? Your wife's install was ok after extensive upgrade?

Well that at least is good news.. I usually do a clean install myself.. but I'll be happy just to get back up, a reinstall can come later, thx for that.. I thought it was all hardware tied now.

My connections seem fine but I'll try to short it tomorrow when I'm sure it's dry and definitely not working.

Cheers.
 
Just to finish the post.

I tried to short the connections, nothing happened. so I've no idea what's wrong with it.

I've had to order a new mobo, but I figured as long as I was doing that I may as well update my chipset, so coming from my beloved Q9550, 8GB Ripjaw 1600 ,Ramp Extreme 1 and HD 4890, I'm upping to an i5 3450, 16GB generic 1333, Asus P8H61-MX (micro ATX with usb3 and PCI-e3) and an Evga GTX 660 SC.

Yeah, I'm ending up with a FAR better machine, but I could have done without the hassle and expense :(

Thx for the replies peeps.
 
Back
Top