Northbridge heat sync for IC7 Max3?

Halpertal

n00b
Joined
Oct 10, 2004
Messages
4
Well that wonderful cheap ass fan on the NB has given up on my Abit IC7 Max 3. I was wondering what the [H] crowd thought of a good replacement. I was going to find a thermalmax tiger 1 but couldn't find one in stock. The fact that it's not made for my chipset also bothered me and wondered if anyone has used one on a i875p chip.

What northbridge cooler would you recommend i use? I don't really want to spend a lot of cash on it and do overclock a little bit but not that much that i need a massive heat sync.
 
What northbridge cooler would you recommend i use? I don't really want to spend a lot of cash on it and do overclock a little bit but not that much that i need a massive heat sync.[/QUOTE said:
NB-1 from thermalright that will cool your NB chip pretty good. :D
 
mine on my nf7s is about to go out :( it will go really fast for like 10 seconds, then for about a minute will go reallllllyyy slow and do it all over again..
 
have you taken a look at the zalman cooler? It's passive, but rather large. I haven't used it, but it seems it would do a great job.
 
I'm using one of the zalman passive coolers. Works pretty well..installation sucked because there aren't any holes on the mobo. Had to get a paper clip and bend it around to get the heatsink to stay. The thermal adhesive didn't work too well...the heatsink fell off pretty quickly =/
 
Thanks for the info. The thermalright looks to be the best option right now. My only concern is the noise level.
 
Halpertal said:
Thanks for the info. The thermalright looks to be the best option right now. My only concern is the noise level.


dont even worry about the noise level.. you wont hear a thing. Make sure you dont get any thermal compound on it like i did (noob). it was my first installation of NB heatsink and i did a sloppy job. got the thermal compound on my fingers and ended up touching the fins and later on had to clean it due to it making a bit noise, after that it was fine.
 
lostpnoiboi said:
dont even worry about the noise level.. you wont hear a thing. Make sure you dont get any thermal compound on it like i did (noob). it was my first installation of NB heatsink and i did a sloppy job. got the thermal compound on my fingers and ended up touching the fins and later on had to clean it due to it making a bit noise, after that it was fine.
disagree
disagree
disagree

It has a high pitched whine... which is the type of noise that bothers me most. It's noticeable over other quiet components (truecontrol PSU turned halfway down, fans controlled by the connectors). Setup also includes watercooling + seagate HDDs, so i guess you could say my system is pretty damn quiet. The fan is being controlled by a zalman fanmate, and turned most of the way down is pretty quiet.
 
I'm using a Zalman 32J passive NB heatsink on my IC7 thermally adhered to the mobo with the Zalman supplied thermal adhesive and it's stuck there like a rock.
I let it set up for over an hour not the 15 minutes like the instuctions said and it ain't going anywhere.
It looks good next to the Zalman 7000 alcu I just installed an hour ago. :)

Everthing is really "cool" now.
 
diredesire said:
disagree
disagree
disagree

It has a high pitched whine... which is the type of noise that bothers me most. It's noticeable over other quiet components (truecontrol PSU turned halfway down, fans controlled by the connectors). Setup also includes watercooling + seagate HDDs, so i guess you could say my system is pretty damn quiet. The fan is being controlled by a zalman fanmate, and turned most of the way down is pretty quiet.


i have six 80mm fans, one 120mm fan for my xp120. And the NB-1 fan is as quiet as any of those fans are.
 
lostpnoiboi said:
i have six 80mm fans, one 120mm fan for my xp120. And the NB-1 fan is as quiet as any of those fans are.
are you running all of them at the full 12v? I have 1 120mm ~7v and 3 80's 5v (just to pass a little air over my pump) and the NB1's fan was by far the loudest component. I'm not saying it's a SUPER noisy fan, because it's not ridiculous or anyhting, but it's whiny, and high pitched (noticeable with my case closed).
 
So i got the NB1 installed. It's really not that loud. It does make a high pitch sound but it's not noticible over any of the other stuff running in that room. The noise is not a factor.

However i was disapointed to find NO instructions in the box. The finish wasn't that good either and required quite a bit of lapping too. Other than that the thing rocks. Up and running again.

Thanks for all your input.
 
Back
Top