Help with asus p4800 e deluxe

Cyber

Limp Gawd
Joined
Dec 7, 2003
Messages
190
new build with a asus p4c800 e deluxe and flashed bios to 1015. said reading flash, erasing flash, and writing flash, then prompted me to do a reboot. i dont have windows xp pro yet installed and got a error that said no drive to fast track controller, the bios is not installed. then i set primary boot to raptor drive and did reboot and got same errors. any suggestions? could it be due to i dont have my 2nd raptor installed yet. should be here any day now. hope i didnt mess anything up seriously.
 
Do you have the bios set to use RAID? It's possible that it expects RAID but the SATA RAID bios is not installed...

Other than that, I can't help you as I don't have a Pentium based system.

Good luck.
 
You need to turn off the RAID setting if you only have one drive installed and your using the RAID controller.
 
I am getting this same error as well on m y P4P800. I only have one a ATA HDD. In the BIOS I turned off RAID, but I am still getting the BIOS NOT INSTALLED error. I have tried drivers etc... I haven't flashed the BIOS though...

Also, does PAT go under a different name in the BIOS?
 
That's the main difference between 865 and 875 chipsets man. 865s don't have PAT. 875's do.

However Asus has a implementation that is similar but yes it goes by another name on the P4P800 since its not actually PAT. But it does the same thing basically as I understand it.
 
Doh! I have a P4C800. Not a P4P800... Anyway, I haven't seem a PAT setting in the BIOS.

OT:
Fragalot-- Do you get the Fast Track BIOS error?

I also have an IRQ conflict with my AGP. Is there an easy way to specify IRQs?
 
The PAT feature is called something else actually. I'd have to look in my BIOS to see. Actually the motherboard manual is pretty good about explaining BIOS options.

And I did get the fast track error before I told it not to run in RAID mode. I do have a drive hooked to that controller.

By default it wants to run the controller in RAID mode.
 
Yeah, I was worried that if I turned it off it would screw with my HDD. I said fuck it though, and gave it a shot... and it worked.

Now I am trying to figure out how to assign IRQs. My GPU is sharing an IRQ with 2 USB controllers. I have tried eveything (like RTFM) to no avial. On my CUSL2-BP I was able to assign IRQs with no problem. The best I was able to do so far with the P4C800 D, was disabling most of the onboard shit I didn't need, which resolved my IRQ conflict with my Audigy. However I don't want to disable my USB controllers because I use that shit...

It's probably not an issue, really... I haven't heard any pops or static since I resolved the sound card IRQ issue. However, I would rather have zero conflicts...

PAT is called Performance Mode or Performance Accelertaion Mode (PAM). It makes my system unstable... :mad:
 
I have had absolutley no issues with PAT. In fact I notice a slight difference in performance with the PAT enabled.

On those boards I have never had IRQ issues. Is your PNP OS option set to on or off? If it is set to off turn it on. Let Windows handle IRQ management.

Make sure ACPI is enabled also. Are you running Windows XP or Windows 2000? That would make a difference also.
 
I am running XP Pro.

I have tried the PNP OS option enabled and disabled, it doesn't make a difference.

ACPI is enabled.

I don't think the RAM is up to speed to enable PAT. I have 1GB (2x512) mushkin PC3200-2.5 default timing/settings.
 
Back
Top