Fastest processor on a MSI KT3 Ultra?

Joined
Aug 15, 2003
Messages
45
I'm trying to decide how fast should the processor be on my motherboard. According to the manual, it supports Ahtlons Duron\MP\XP flavors and has a FSB of 200/266/333mhz. But also it says max is at Athlon 2100+. Should I take the second line with a grain of salt? I'm guessing the 2100+ was the fastest Athlon out at the time. I'm also thinking of throwing in a Barton 2500+ or the 3000+ if I'm capable so please help.
 
if i recall, it supports memory up to 333 and FSB up to 133. It dose not offically support 166 and 200 FSB cpus, nor dose it offically support DDR400 (PC3200) And it dose not support Barton CPUs at all. So i woud stick to Tbreds, liek a good 1700+ or a 2100+....and overclock it. The 2400+ and 2600+ will work with that BIOS, but the 2500+ and 2700+ andup will not work. (i think there is even a 2800+ Tbred)


I had this board and loved it. I didThis voltmod to get my Vcore up to 2.03v and ran a 1600+ 200x10 (2Ghz) 100% stabel. So i know some of the Kt3s will do 200 FSB. Just for kicks i put my week 48 2100+ in it and it ran 12x200 (2.4Ghz, 2.03v) just fine. I also ran a pally core 2000+ 1.8Ghz for a wile too. that CPU sucked balls though... I also knwo it works just fin with corsair PC3200 DDR....

Hey i pulled up this pick from a long time ago of the KT3 in action!
setup02.jpg

EDIT: at one point i had 2 stick of Corsair PC3200 DDR,...I wonder where the other on is in this pic?>
 
Damn...I thought the FSB under "Chipset" was still about the processor :( Oh well, guess I can throw the extra money into the memory! Any suggestions for OCing?
 
I ran a 2500 barton in a kt3 ultra for a long time, even overclocked it to 3200. It will support a barton, but for some reason it hated my ram after i switched froma 1700 to a 2500 barton.
 
The CPU speed is FSBxRatio (multiplier), so FSB dose effect the CPU, it’s also affects your ram, as you ram speed it FSBx2, you if you FSB is 166, then you need to have at least DDR333 (PC2700 333Mhz)

Take note that FSB on this board also affects the PCI and IDE clocks, so as you raise your FSB you are raising you PCI clocks form 33Mhz (stock) and up...im not sure the ratio of the PCI vs. FSB, but I think a 200FSB will yield 50 MHZ PCI...at 210 FSB none of my hard drives would work because there controller was overclcoked past there spec..., so what I did was bought a PCI 33Mhz/66Mhz RAID Card, and ran RAID. The card could handle the higher PCI speed because it was made to run up to 66 MHz (64bit PCI) it worked great and never game me any problems... My CD-ROMs never really gave me problems on the onboard controller. No sure why… but I wasn’t complaining. I also ran a sound blaster adugity (spell check please) in one of my PCI, it did fine too. The cards I had problems with were NIC cards, finally went with a nicer 40 dollar Linksys and It worked great…

So if all this trouble why even touch the FSB? Because you will get more performance out of higher FSB, this increases the CPU speed and memory speed, if you just unlock the multiplier on the CPU and up it you will only gain MHz out of the CPU…..

I would say shoot for at least 166FSB, with some 333 RAM, or some good PC3200 and run it titer timings at 333..

And about the comment above, if you got a Barton working, tell us how and what BIOS. Chunky Egg Foo, if you can get a Barton core working, then I would suggest a Mobil Barton 2500 or 2600+ they over clock very well.
 
I have the kt3 ULTRA ARU running the Barton XP2500 O/Ced to a 2800. Only can go that far because of my ram, which is only pc2100. MSI doen't offically support the bartons, but just get the 5.7 bios andy you are good to go. OH make sure your ram can do 166 as well.
 
Should the bios be flashed before the chip is inserted? Or what would happen if the Barton is in there and you boot up? I don't have a floppy for this machine...
 
I am thinking it will only read the chip as being a lesser chip and run it at 100 or 133 fsb.. Shouldn't hurt anything.
 
So in theory I can buy a Barton 3000+, pop it in there, flash the BIOS and hope it fixes everything? Just want to know why you stop at a 2500+ and not something higher.
 
Well, the board will only boot a 133 FSB, so if you "pop" in a 3000+ it will boot at the wrong speed. You will have to manuell set it to 166 or 200...either on will be overclcoking the board past spec. And you might want to make sure it is useing the full 512k cache of the barton. Mabey a program like CPUis will tell you. Im assumming if the CPUID says 512k L2 then it will be useing it....it may say 256 even thought it a 512k barton..... then you up shit creek withough a paddel.

The reason most people dont even mention past 2500+ is that its pointless to buy anything higher. as the 2500+ will overclock to the same speeds the rest of the bartons will... assumming the board can handel it. So why waste the money...
 
How stable would you think the board be if a Barton 2500+ is on it? Just remembered I'm using this board as my server and it seemed kinda silly for me to do all this extra work for a marginal increase in speed (Thoroughbred 2100+ vs. Barton 2500+).
 
Chunky Egg Foo said:
How stable would you think the board be if a Barton 2500+ is on it? Just remembered I'm using this board as my server and it seemed kinda silly for me to do all this extra work for a marginal increase in speed (Thoroughbred 2100+ vs. Barton 2500+).

Why are you overclockign a server in the first place?

but a barton 2500+ paired with some PC2700 or higher ram running 166 (stock for ram and CPU, overclcoked for board) Should run just fine.

The board has on built in PCI Divider, a 5/6 that comes on when at 154, if i remember correctly. That will help keep the PCI speeds down a bit. its work out perfec if your only going to run 166...
 
I have been running my 2500 at 166 for about a year now with no worries, and thats using pc2100 memory. You'll be fine
 
Paully's5.0 said:
I have been running my 2500 at 166 for about a year now with no worries, and thats using pc2100 memory. You'll be fine


So are you guaranteeing him his PC2100 will do 166?... a lot of PC2100 ram will not do 166, you cant be telling people that a certain overclock is for sure, nothing about overclocking is guaranteed. You seem to have some good stuff. I’m assuming your running Sync? Sync is the best way to run a AMD box.
 
For reference, my MSI KT3 Ultra was definitely not stable at 166MHz FSB with verified working PC3200 and PC2700 DIMMs.

I would second the suggestion for an AXP Mobile 2600+. A 133MHz FSB by default with a guaranteed unlocked multipler seems like a good idea to me with a KT333 board. This is assuming the board doesn't choke on the Barton core, which other people have suggested it will not with the proper BIOS.
 
What do I lose if I go Mobile? Or is the chip operating under a lower FSB? When I think of mobile power, I think of those underpowered laptops. :mad:
 
I(illa Bee said:
So are you guaranteeing him his PC2100 will do 166?... a lot of PC2100 ram will not do 166, you cant be telling people that a certain overclock is for sure, nothing about overclocking is guaranteed. You seem to have some good stuff. I’m assuming your running Sync? Sync is the best way to run a AMD box.

Considering he hasen't mentioned what he has for memory, no I am not guaranteeing his "pc2100" will work. I was just saying that me having pc2100 an running just fine, that pc2700 or higher memory should be alright just as well. Check the msi boards over at amdmb.com and I assure you that many others will suggest that this board will be alright at 166, many will say it can go higher.

I am using crucial memory, not known for its extreme o/c abilities at all, but I have been fine and can't understand that someone else couldn't have the same results. Granted I did have to drop the settings to cas2.5 to make it work. Yes my system is running in sync.
 
Paully's5.0 said:
Considering he hasen't mentioned what he has for memory, no I am not guaranteeing his "pc2100" will work. I was just saying that me having pc2100 an running just fine, that pc2700 or higher memory should be alright just as well. Check the msi boards over at amdmb.com and I assure you that many others will suggest that this board will be alright at 166, many will say it can go higher.

I am using crucial memory, not known for its extreme o/c abilities at all, but I have been fine and can't understand that someone else couldn't have the same results. Granted I did have to drop the settings to cas2.5 to make it work. Yes my system is running in sync.

I know it will be good at 166, i ran my 210x10 1:1 on memory. but you cant garentee his PC2100 will do 166...
 
I(illa Bee said:
but you cant garentee his PC2100 will do 166...

He hasen't said ANYTHING about using pc2100 memory! He hasen't said anything about memory, I just gave him my set up. If he had asked for recommended memory I sure as hell wouldn't say you'll be fine with pc2100.
 
Chunky Egg Foo said:
What do I lose if I go Mobile? Or is the chip operating under a lower FSB? When I think of mobile power, I think of those underpowered laptops. :mad:
The mobile CPUs run lower voltage lower FSB, I i think they defaule lower core speed. But there are great chips. The all have un-locked multiplyers and dont need as much votlage to run stock speed. That means (this is the case with most) if you give them desktop votlages, the fly! i can run mine 2400 Mhz with just 1.75v, and 2730MHz with 2.0v. Plus, if FSB overclocking is holding you back because of the board or memroy, then you can get some nice raw CPU MHZ with the unlocked multiplyer.

a Mobile will be you best bet id say...

Paully, It just sounded to me like he was saying that PC2100 (in general) will do 166, and i wanted to make it clear than it will not. Some sticks will but most will not, and i didnt want to give the tread starter the wrong idea...
 
Back
Top