dfi ultra infinity nfII

D

DigitalChaos

Guest
just a few questions. probably been answered a million times but search = b0rked.

anway.. multiplier. i would think i would need to know if the board can go to 233fsb and kick in a 7 divider to keep my pci and other busses at normal speeds. someone told me i dont need to worry because the multipliers are "locked" on an nforce board.. what does this mean? could i have ANY FSB and the pci and other busses stick to their spec? essentially i want to bring the FSB as high as possible(while dropping multiplier) yet keeping all my other busses at spec. obviously i would get ram of higher speeds to keep up.



second: ram.. do i WANT pairs or does it matter? I am still debating 512 vs 1gb, and cas latency has never really show much performance difference to me.. so i am just going with the speed from my above question.. but alot of the 512 pairs (256x2) seem more expensive than just a stick of 512. do i want pairs?




third: correct me if i am wrong but i would believe i will see alot of performance via bumping the fsb of the cpu and bringing the ram up... and the cas latency isnt going to really matter. I am not looking for a few 3dmarks here.. just overal aparent performance.
 
Originally posted by DigitalChaos
just a few questions. probably been answered a million times but search = b0rked.

anway.. multiplier. i would think i would need to know if the board can go to 233fsb and kick in a 7 divider to keep my pci and other busses at normal speeds. someone told me i dont need to worry because the multipliers are "locked" on an nforce board.. what does this mean? could i have ANY FSB and the pci and other busses stick to their spec? essentially i want to bring the FSB as high as possible(while dropping multiplier) yet keeping all my other busses at spec. obviously i would get ram of higher speeds to keep up.



second: ram.. do i WANT pairs or does it matter? I am still debating 512 vs 1gb, and cas latency has never really show much performance difference to me.. so i am just going with the speed from my above question.. but alot of the 512 pairs (256x2) seem more expensive than just a stick of 512. do i want pairs?




third: correct me if i am wrong but i would believe i will see alot of performance via bumping the fsb of the cpu and bringing the ram up... and the cas latency isnt going to really matter. I am not looking for a few 3dmarks here.. just overal aparent performance.


1. All NForce2 motherboard have locked PCI of 33 MHz and separate (yet adjustable) AGP of 66Mhz. So yes, if you run a 250 MHz FSB your PCIs are still just 33 MHz….you memory is adjustable try dividers also. But on a AMD system it is always best to run then the same, AKA Sync, 1:1 ratio.

2. Yea you want 2 pairs, as the main feature with the NForce2 is to run dual channel memory, you only want 2 stick wile the board will support 3, it is best to run 2 exact alike sticks… I would recommend getting 2 256 sticks of either some good PC3200 such as Muskin level2, or corsair, or some 3500, like Kingston hyperX, or musking level2 again.. Do your research on what memory to get as it is key! And I haven shopped for memory in awhile so I may be out of date on my suggestions there.

3. CAS latency dose matter…my system will run 245FSB with sync memory for 490MHz with CAS3, but my system performs better running 235 FSB (470 memory) with CAS2.0 personally I would shoot for as mush of a FSB increases you can get will keeping your memory timing down low, like 2.0-2-2-6, or 2.0-3-3-7. With some good memory you should be able to run 2.0-3-2-6 at 215Mhz FSB or so…give or take…

its always nice to fill in all that memory bandwidth with some RAW CPU Power…so get some cooling an up that Multiplier (RAW CPU MHZ!!!)
 
BTW: soem laste reports form various people, includeing myself...the china made infinty ultras have stability problems when runnign higher that 1.8v, infast, they cant without crashing.

I ended up sendign mine back and replaced it with a Abit Nf7, cheaper and better if you ask me.
 
Originally posted by I(illa Bee
BTW: soem laste reports form various people, includeing myself...the china made infinty ultras have stability problems when runnign higher that 1.8v, infast, they cant without crashing.

I ended up sendign mine back and replaced it with a Abit Nf7, cheaper and better if you ask me.

well ill be going with a mobile.. so ill have a big voltage advantage there. i wouldnt want to put more than 1.8v to the proc really. usually 1.75 is my comfort level
 
Originally posted by I(illa Bee
1. All NForce2 motherboard have locked PCI of 33 MHz and separate (yet adjustable) AGP of 66Mhz. So yes, if you run a 250 MHz FSB your PCIs are still just 33 MHz….you memory is adjustable try dividers also. But on a AMD system it is always best to run then the same, AKA Sync, 1:1 ratio.

2. Yea you want 2 pairs, as the main feature with the NForce2 is to run dual channel memory, you only want 2 stick wile the board will support 3, it is best to run 2 exact alike sticks… I would recommend getting 2 256 sticks of either some good PC3200 such as Muskin level2, or corsair, or some 3500, like Kingston hyperX, or musking level2 again.. Do your research on what memory to get as it is key! And I haven shopped for memory in awhile so I may be out of date on my suggestions there.

3. CAS latency dose matter…my system will run 245FSB with sync memory for 490MHz with CAS3, but my system performs better running 235 FSB (470 memory) with CAS2.0 personally I would shoot for as mush of a FSB increases you can get will keeping your memory timing down low, like 2.0-2-2-6, or 2.0-3-3-7. With some good memory you should be able to run 2.0-3-2-6 at 215Mhz FSB or so…give or take…

its always nice to fill in all that memory bandwidth with some RAW CPU Power…so get some cooling an up that Multiplier (RAW CPU MHZ!!!)

gahhhh.. that is soooooooooo cool. i am used to having to mess with dividers


as for ram.. what you are suggesting is sticking at cas2.. and then taking the extra $ and applying it to the FSB of the ram.. hrm alright.

if 2x256 is all you need ill probably get some cas2 pc4000 mushkin. the proc should be able to do that speed as long as i drop the multiplier... should have any problems with getting a fsb that high should i? i see no aparent bottlenecks as long as ram is taken care of and the multiplier is worked down
 
I still would not pay the preium for PC4000, as it it the same as most PC3200 and 3500, but the 4000 runs like 3.0-4-5-8..

Bahsaaa I know ym kingston hyperx 3500 will run 4000 Speeds if i set it to shitty timings like that...

PC4000+ is a joke...

BTW: I am running a 2400+ mobel too, i can only get to, 2.4Ghz with 1.8v, onl ym old (dead) NF-7 I could get to 2.8 with 2.0v!
 
u can get mushkin pc4000 and hyperx pc37000 512mb sticks at newegg both for $116. they are about even in my opinion, but if i had to pick i would get the mushkin.
 
Back
Top