can a flash drive causes interference on LCD screen?

Happy Hopping

[H]F Junkie
2FA
Joined
Jul 1, 2004
Messages
8,582
we got a a few mth. old PC, very nicely built, and the guy said every once in a blue moon, when he connects a kingston usb flash drive, his LCD will see vertical lines.

So the LCD was swapped out as it's many years old, and replaced with a new screen.

Now, he said in 1 incident, when he insert the USB flash drive, the screen turns red

The front USB port is connected to the USB port on the motherboard, how can that cause interference on your video port?

is this a defective kingston USB flash drive or something wrong w/ the front port?
 
USB 3 can cause interference in the 2.4 GHz Wifi band.

http://www.pcmag.com/article2/0,2817,2423604,00.asp

http://www.usb.org/developers/whitepapers/327216.pdf

When I use a USB 3 drive connected to the front of my HTPC, my wireless keyboard + mouse range drops to shit. But if I use a USB 2 device in the same port, nothing happens because the signaling rate is lower.

If he's using USB 3 (both port AND device), that's likely the issue. Otherwise, I don't know.

Is he using VGA to connect the monitor, or a digital connector? I've seen improperly shielded VGA connectors cause interference on monitors before, so if you see it (1) try a new cable and (2) try a new PC to drive the monitor. Any part of that chain could be causing interference.
 
Last edited:
Hmmm, are you sure?

http://hardforum.com/showthread.php?t=1575774

I know the manual for my motherboard mentions it as well. Not to say that this is cause of the OP's issue, but it seems logical to me that it would be possible for a usb3 port to effect data on a pcie lane according to that post...

Yes, a motherboard with lots of 3rd-party devices hooked up to only -so-many PCIe lanes can end-up having those devices fight each other for bandwidth, but that shoun't be related to visible corruption on a screen.

At most that might impact gaming framerates, but not the picture quality.
 
USB 3 can cause interference in the 2.4 GHz Wifi band.

http://www.pcmag.com/article2/0,2817,2423604,00.asp

http://www.usb.org/developers/whitepapers/327216.pdf

When I use a USB 3 drive connected to the front of my HTPC, my wireless keyboard + mouse range drops to shit. But if I use a USB 2 device in the same port, nothing happens because the signaling rate is lower.

If he's using USB 3 (both port AND device), that's likely the issue. Otherwise, I don't know.

Is he using VGA to connect the monitor, or a digital connector? I've seen improperly shielded VGA connectors cause interference on monitors before, so if you see it (1) try a new cable and (2) try a new PC to drive the monitor. Any part of that chain could be causing interference.

well guess what? it is in fact USB 3.0 Kingston. But the interference is on the LCD display though, not wireless router. But they do have a wireless router and a wireless USB receiver for internet purpose.

Regardless, how do we tie the above to a brand new 28" LCD screen from Viewsonic? The cable is HDMI. It's the only digital cable that c/w this 28" LCD.

The older monitor that we recycle was only the blue VGA though.
 
Last edited:
Did you actually see the problem before you swapped the display?
Was the PC still working after the problem occurred?

Have you seen the problem when it occurs with the new display?
 
Did you actually see the problem before you swapped the display?
Was the PC still working after the problem occurred?

Have you seen the problem when it occurs with the new display?

Q 1: Yes, on an old Dell screen

Q 2: Yes, fully and absolutely no other problem in any way

Q. 3: Yes, once. a pink screen, and can't duplicate the problem since
 
Sounds like a gfx card problem, or at least something causes the gfx cards memory to corrupt.

I have a DAC connected to my PC with unshielded USB wires.
The DAC is prone to crashing occasionally.
ie if I plug in my camera via USB, when I unplug or switch off the camera, my USB DAC crashes every time.
Its not a fault of the camera, but of my DAC now being sensitive to sharp sources of EM radiation. In my case the problem is self induced.
It cant be power connection related (between PC and DAC) because I havent connected the power lines on USB, only the signal lines are connected.

So it could for example be the pulse of EM radiation when you connect/disconnect the USB pen that is upsetting your gfx card. Try another gfx card.
The alternative, it is power related meaning the PSU could also be suspect for not having good enough regulation/noise rejection or is just worn out.
 
Alright, today is the 1st time I've seen the problem that he describe over the phone. In the past, he describes those pink screen and vertical line on the old monitor, and I didn't see it on my own until today.

I think there is a short circuit on the front panel, it's not a pink screen or vertical line, the screen is OFF because the PC is turn OFF by inserting a USB at the front port.

So it looks like some soldering is off that creates a short circuit, so once you connect a USB, it shut down the PC, but not all the time, so far, I have seen it twice w/ today being the 2nd time.

I saw this 2 weeks ago when I swap out the old LCD and install the brand new LCD. I thought I may be accidental push a button when the PC turn off by itself. I should have know better. But after I do the turn on -- boot up -- Shut down 10 more times that day, nothing happens that day, so I ignore it.

Today, I see it for the 2nd time. This is the 1st time I've seen a short circuit on a very new case.

The USB flash drive inserted at the front today is a different USB flash drive. So, I think by replacing the front panel, it should fix the problem. What do you guys think?
 
See what happens when you use a rear usb port.
If that still crashes the pc, disconnect the front panel and try again.
If it still happens, try another psu.
 
You don't think it's a defective front panel? Because the shut down happens the moment I insert the 2nd USB flash drive (USB 2.0 verbatim) in it. Why do you think it's a PSU issue?

because the sys. is very stable if you don't touch the front USB ports
 
Read my last post again, then the one before.
You arent the only one troubleshooting this, thats why I am replying to assist.
It would be handy if you did things that make it easier to diagnose.
 
I figure it out. He short circuit the front panel w/ static electricity from his body to the thumb drive to the front panel
 
So what you're saying is he simply zapped the computer case which happens all the time.

The outermost shield of the USB ports as well as on the connectors are connected to the PC case, which in turn has its own low impedance path to ground. So that scary 'sparking' happens in a different place - especially designed for this.

The front panel or its wiring can be faulty.
Both USB and your VGA monitor use the 5v rail, while most other components utilize 12v. That might be why it's affecting video.

If there's a slight short somewhere in the panel then the voltages (between the thumbdrive and usb port) will equalize partially via the motherboard - causing a crash.

Are your power outlets properly grounded? Monitor plugged in to the same outlet as PC? no UPS or line conditioners somewhere?
 
When you said all the time, how come there isn't more of threads like this around here? Anyhoo, I have to post a separate thread to see if there is some cases that is better build on grounding than others

It's not affecting the video, that's what he said over the phone, all it is, the power shuts off, so the screen is white, or some zip vertical line , it's just no HD signal

Then the PC starts up at safe mode

power outlet is on a half decent surge protector, proper grounded, but no UPS or Line conditioner. This is someone else PC, but I'm glad it doesn't happen to me
 
Last edited:
There are few threads about this because its often easy to realise by the feel or the noise it makes.
Look up ways to prevent static build up in the home and on your body.

ie
some things that increase static creation:
synthetic clothes, carpets, shoes rubbing against each other as you move.

things that allow static build up:
not being near an earth of any form as you move around your home.
isolation from the floor with synthetic fibre flooring, footwear and socks.

Cotton or woolen clothes, going bare foot or wearing leather soled shoes reduce static greatly.
Some carpets are incredibly good at creating static and can cause the problem in their own right. If so it might be wise to replace it.
 
Back
Top