Bilding large storage with 2TB disc and HighPoint controller

It's generally good practice to size the UPS to the power supply. While this will actually be overkill in most cases, considering the shear number of drives you're talking about, it's what I would do. Remember that UPS's are rated in VA, not W. A 1000VA UPS may only be good for ~700W. You also have to consider what else will be plugged into the UPS. Monitor? How long to you need gracefully shutdown the rig? Make sure you get a UPS that can interface with the OS correctly. I'd be looking in the neighborhood of 1500VA minimum.
 
I suppose my response did come across a bit cryptic. There is no reason for me to try to explain it here, when so many white papers can do a better job! Here is one by Intel, although there are others if you search. http://lmgtfy.com/?q=Intelligent+RAID+6+Theory+Overview+and+Implementation

UREs (Unrecoverable Read Errors) are the culprit, particularly during rebuilds, only made worse by long rebuild times and mounting probabilities against you. Like I said, just read the white paper! The 1 in 3 I got from a worksheet calculating the probability of a read error happening at least once if reading all data from all disks.

I use 12 drive arrays, and I let data verify/scrub run against the array at least every few weeks. It seems like it reports fixing one data error (through the parity data) at least every 4th or 5th time I run that!
 
Drives don't take much power. I run my file server, my i7 desktop, my laptop, my VIA NAS, networking gear (router and a large switch), and my FW900 monitor off my 1500VA APC UPS (with a second battery) and I get about 30 minutes out of it. My file server really only takes about 300-350w, so I don't imagine yours will be any different.
 
I'd also recommend at least an APC1500. If uptime if really important you might consider a model with an external battery option. I have (4) 100amp hour deep cycle batteries connected to mine, homebrew hack!

Main goal of the UPS is to allow for a clean sync'd shutdown. Although I'm a firm believer that once a HD is spinning it should stay that way forever!
 
I'm looking at the APC1500 (sua1500i) but as far as i can tell that doesn't support adding additional batteries does it? Then i would have to go with something like surt1000xli or surt2000xli right? That's a bit more expensive.

Blue Fox You are right they don't use that much, they will use a MAX of 6Watt and that would be on startup. But its still good to have some extra time.

madcoder Thanks that was actually helpful. Even thou I didn't quite understand the chart (Figure 1) But I still get the point. The more TBs there is, the bigger the chance for a Fatale read error.
 
I'm looking at the APC1500 (sua1500i) but as far as i can tell that doesn't support adding additional batteries does it? Then i would have to go with something like surt1000xli or surt2000xli right? That's a bit more expensive.

You can actually add an external battery to any APC ups, but it involves cutting the case and modifying the "battery constant" parameter in the firmware. If you are electrically savvy then it's fairly easy, otherwise best bet is to get APC's solution.
 
Check out craigslist. I picked up (2) 2200VA APC SmartUPS's with network management cards for $200. Of course they both have some cosmetic damage and have an aged look; one had bad batteries. Even with that though, If you can work with a rackmount format, that's the direction I would go.

I do agree with Blue Fox though, I'm running my file server with a Q8200, 10TB, plus 3 managed switches on less than 400W. And that 400W is where the UPS plugs into the wall, so that includes the UPS inefficiency.
 
Just for sheets and giggles, you should RAID 0 all those drives and run some benches. I realize after a few drives raid 0 loses its luster but still be cool to try before you do the raid6
 
Back
Top