Just as an update for anyone else who happens to be in the same situation someday:
I was successful in getting my Antec HCP-1300 to work with Quadfire 290X (295x2 + 290X + 290X). Saved me about $450 since I was about to get a Corsair AX1500i (or $300 for another Antec HCP-1300, but my case only fits a single PSU). Only cost was a few hours wracking my brain for the solution.
From memory (I'll check and update if anything's wrong):
|| 12v1 || 12v2 || 12v2 || 12v1 || 12v4 || 12v3 ||
|| 12v1 || 12v2 || 12v3 || 12v4 || 12v4 || 12v3 ||
|| 1A || 2A || 2C || 1C || 4A || 3A ||
|| 1B || 2B || 3C || 4C || 4B || 3B ||
|| 1A = 295X2 8-Pin #1 || 2A = 295X2 8-Pin #2 || 2C = Extra 6-Pin PCI-E Power to Mobo || 1C = Blank || 4A & 3A = 290X #1 via 16-Pin Connector ||
|| 1B = Blank || 2B = 4-Pin PSU || 3C = 8-Pin CPU || 4C = Extra 8-Pin Cable from PSU "MB" Connection || 4B & 3B = 290X #2 via 16-Pin Connector ||
Feels like I'm forgetting a connector somewhere, but like I said this is from memory so I'll update later. The main thing I had to do was connect each 295X2 8-pin to its own individual rail and minimize what else may be on those rails that could overload it. I kept getting black screens when I tried using 4A+3A and 4B+3B each for the 295X2 only, everything else being the same. I have a feeling this wouldn't have worked if I had a 295X2 CF setup, but I don't know enough about electrical/PSUs to know.
My full rig specs are in my sig, as it's a bit long to write out.
I was successful in getting my Antec HCP-1300 to work with Quadfire 290X (295x2 + 290X + 290X). Saved me about $450 since I was about to get a Corsair AX1500i (or $300 for another Antec HCP-1300, but my case only fits a single PSU). Only cost was a few hours wracking my brain for the solution.
From memory (I'll check and update if anything's wrong):
|| 12v1 || 12v2 || 12v2 || 12v1 || 12v4 || 12v3 ||
|| 12v1 || 12v2 || 12v3 || 12v4 || 12v4 || 12v3 ||
|| 1A || 2A || 2C || 1C || 4A || 3A ||
|| 1B || 2B || 3C || 4C || 4B || 3B ||
|| 1A = 295X2 8-Pin #1 || 2A = 295X2 8-Pin #2 || 2C = Extra 6-Pin PCI-E Power to Mobo || 1C = Blank || 4A & 3A = 290X #1 via 16-Pin Connector ||
|| 1B = Blank || 2B = 4-Pin PSU || 3C = 8-Pin CPU || 4C = Extra 8-Pin Cable from PSU "MB" Connection || 4B & 3B = 290X #2 via 16-Pin Connector ||
Feels like I'm forgetting a connector somewhere, but like I said this is from memory so I'll update later. The main thing I had to do was connect each 295X2 8-pin to its own individual rail and minimize what else may be on those rails that could overload it. I kept getting black screens when I tried using 4A+3A and 4B+3B each for the 295X2 only, everything else being the same. I have a feeling this wouldn't have worked if I had a 295X2 CF setup, but I don't know enough about electrical/PSUs to know.
My full rig specs are in my sig, as it's a bit long to write out.