Am I screwed?

Bladestorm

[H]ard|Gawd
Joined
Dec 10, 2006
Messages
1,232
I'm having a difficult time trying to remove an H50 bracket from the underside of the CPU socket because of the double sided foam sticky pads. I foolishly tried cutting through the foam with an x-acto knife, and what appears to be the smallest resistor I've ever seen fell off. I can't tell exactly where it came from. I had planned on re-purposing the board. Am I screwed?

IMG_1328.jpg
 
It's actually a tiny capacitor(work with parts like these for a living). I personally wouldn't try powering on the board without it. We've seen boards at work fail test, damage/fry components with what would appear as a minor defect(bad solder joint) let alone a missing part.
 
either weld it back carefully or replace it with one of the same capacity...

edit: I almost forget: N00b!! ;) :D
 
Oh you're a woman. No wonder you don't know what you're talking about. Got it.


To the OP, I'd still try it. If this is a "re-purposed' system ten you shouldn't have anything to lose.
 
But tired so I don't exactly understand what you have written.

If it came of the motherboard then you are fucked.

If it came of the back of the CPU then you should be fine.
 
Oh you're a woman. No wonder you don't know what you're talking about. Got it.

hehehe

uwrpK8E.gif



To the OP, I'd still try it. If this is a "re-purposed' system ten you shouldn't have anything to lose.[/QUOTE]

Suuuure, have him fry his board :rolleyes:
 
Suuuure, have him fry his board :rolleyes:

The board is probably already destroyed. OP wont know unless he tries. I only recommend him trying if he has nothing to lose from it. :rolleyes:
 
If you arent going to replace the capacitor, just give it a try.
Everything is pretty low voltage, there likely wont be any harm from testing it.
Can you post a picture of where it came from, in case its the VRMs?
 
Can you post a picture of where it came from, in case its the VRMs?

That's just it, I know it came from around the back side of the socket, but I can't tell where. The weird thing is is the capacitor is about the thickness of a sheet of paper, maybe a hair thicker. If it's not the entire thing I'm amazed the x-acto knife made a clean slice off the top of it. I was going to use this board in a mining rig, but I'd be too worried running it 24/7 now.

IMG_1331.jpg
 
What exact motherboard is that? Post revision number too.
 
Well I am sure there is a picture out there somewhere on the Internet showing the under side of that motherboard so I can compare the two, but after about 5 minutes of Googling, I gave up. Haha.
 
Well I am sure there is a picture out there somewhere on the Internet showing the under side of that motherboard so I can compare the two, but after about 5 minutes of Googling, I gave up. Haha.

Thanks for trying. I looked for awhile and found one picture, but it wasn't close enough. I'll have to chalk this one up to a loss. I have another board I can use, but I'm not sure it'll work with the CPU I have. That's another story though.
 
What picture of the under side did you find? I found one and it would have been close enough but it was the wrong section of the board.
 
Hmm.. that's a good enough shot I think, but i need to know how big that piece that got cut off is compared to the others on that section of the motherboard. Can you take another shot of the motherboard w/ the piece that fell off on the board next to the others.

Although without knowing how large it is in comparison I don't think it came from there. Simply because the only possible place that I think it might be is the top right corner, however I think what I am seeing in the picture with the backplate still on isn't anything but the bare metal. Cant really tell without a size comparison if something was supposed to be there.
 
Judging from these pictures I'm guessing I did indeed just slice a piece off. Sorry the pictures are a little out of focus. I unfortunately lost the piece while taking these shots. Guess I breathed too hard. :D

IMG_1339.jpg


IMG_1341.jpg


IMG_1343.jpg


IMG_1347.jpg
 
Holy blurry shot. DSLR? Set the f/stop to like f/20 or something next time! Jeez!

That piece is so small in comparison, try inspecting each one individually to see if one looks damaged.

Being that I have the curiosity of a cat, I'd still boot it. haha
 
Holy blurry shot. DSLR? Set the f/stop to like f/20 or something next time! Jeez!

That piece is so small in comparison, try inspecting each one individually to see if one looks damaged.

Being that I have the curiosity of a cat, I'd still boot it. haha

I said I was sorry! :p My S100 only goes to f/8, and I don't have a macro lens for my 5D.

Looking at the last picture, I'm pretty sure it came from the capacitor in the bottom left corner. The one I placed the piece next to.
 
Don't need a macro lens for the 5D!! lol. we're not!

You are probably right, upon further looking that one does look to be clipped off.

Now the question is, are you gonna try it?
 
The chances that it will catch on fire are extremely slim. Well, if it's going to catch on fire it's going to happen when you first use it, not after it's been running for hours.
 
I'd give it a try.
The chance of it causing extreme heat is very small.
At worst it wont work or will be marginally unstable, possibly worse if clocking depending what the cap did.
It might work fine.
 
I know almost nothing about capacitors and transistors but that looks insignificant enough that I would go ahead and see if it posts and I'm always nervous and pessimistic so that's maybe a good sign. I bet it works just fine. What a horrible mounting system.
 
I decided to try it, and just finished building a system. I'm pretty sure this thing is haunted! It didn't catch fire or anything, and goes into the bios fine, but I have a big problem. With the system off, and ONLY the DVI cable connected the fans on both 7950's spin. With the system off and ONLY the power cord plugged in the CPU fan and all case fans spin. What the hell? They don't spin very fast, maybe 10%, but they make a low squeal.
 
So the 7950s, CPU fan and all the case fans spin? Really hard to understand what you mean.

You say "the fans on both 7950's spin" but you also say "With the system off and ONLY the power cord plugged in the CPU fan and all case fans spin."..

If that's the case, its the PSU.

edit
how are the case fans plugged in? through a motherboard header or directly to the PSU? If directly to the PSU, then it's probably the PSU. If not, then it could still be the PSU since power is leaking out of it somewhere.
 
I'll try and clarify. With only the DVI cable plugged in the fans on both 7950's spin. If I then plug in the power cable (but not turn on the system) the CPU and case fans also spin. The only one that doesn't is the fan that's directly connected to the PSU. The rest are through the motherboard headers.
 
Okay makes more sense now.

Something probably is wrong with the motherboard, but I'm not sure it will have a negative effect on it if you intend to run it 24/7 anyway.
 
I'll do some troubleshooting. The power supply is brand new, well 2 years old, but never used till now. It's an 850w Silverstone 80 plus silver. The DVI cable is hooked up to the 2nd out on my monitor. I know it shouldn't, but might that have something to do with it?
 
I doubt the DVI cable has anything to do with it. Easy enough to test though. Unplug it.
 
I was wrong. With only the DVI cable plugged in, the 7950 and case fans spin. Not the CPU or directly connected case fan. When I then plug in the power cord the CPU fan tries to spin but never makes it. It just moves a few millimeters back and forth, but keeps doing it. If I power the system on, and then shut it down the fans never stop spinning until I pull the power cord.
 
Wait so when only the DVI cable is plugged in and the power cord is NOT plugged in the fans still spin?
 
That's correct, and I figured out why. Somehow it's getting power from the other PC I have hooked up to the same monitor. I unplugged the power to the monitor and the fans still spin. I then unplugged the DVI cable from the monitor and they stopped.
 
An electrical engineer told me the tiny capacitor that broke off may be there for preventing oscillations caused by the other larger capacitors. It's not unusual to put different size capacitors together for that purpose, and losing a capacitor doesn't always result in oscillations.
 
Back
Top