Search results

C_Payne thanks for the custom dual-slot riser ! Put it to good use in my custom 14.5L enclosure, with two 240mm radiator cooling two GTX 1070 and an i7 6700K :)

Waiting for my custom water blocks to move these two 1070 Katana and an i7 6700K from their bench to their custom 12L enclosure :) Right now, the CPU is cooled by an EK Annihilator, the upper 1070 by an EK Thermosphere. Pum pis an EK Sbay DDC while the radiator is a Magicool G2 Slim 240. The...

Upgrade question : is it worth it to move from a Z170 to a Z270 board, given that the latter carries 4 extra PCI-E lanes ? Am I going to benefit from these extra lanes in a dual GPU + single M.2 NVMe drive + 6700K configuration ?

Spartacus : thanks for the detailed explanations and the solder ref. - Thanks for the polarity reminder. I have the connector pinout in the motherboard doc :) - Do you have a particular soldering iron reference you may share ? - What do you mean by wires ends being flat against the board ? I...

DTN107 : thanks for the input. I guess I'll see when I'll have the board. I haven't soldered anything in a long time. I don't want to f*** up a 140€ board :) But yes, that would be the easiest way to power the board : just two wires and a 12V open-frame PSU. Spartacus : yes, that could also...

Thanks again for your help. I get the picture :) Either way (solder or male connector), the issue I forsee is the motherboard DC connector current rating. It is rated for 12A. With a 45W chip and a GTX 1050 Ti single slot, I'm looking at around 13A max. Having to rely on the connector leads...

michalrz Thanks ! Just to be sure, you mean inserting wires where the arrow are, then heat the connector legs above the mobo to melt the solder ? Leaves very few clearance for the iron ! rtangwai : yes, now that I have the exact ref, this certainly what I'm going to do. Except I'll have...

michalrz thanks a lot for your quick answer. Here is a picture of the back of the connector. I do not have the board yet so please excuse the low res. I also found the connector reference : Phoenix Contact Combicon series

Hello, I am quite interested in the motherboard below, a Ling Jiang PCM5-QM77 : socket G2, thin mini-itx with a PCIe x16 slot, wide input. Only issue is the weird DC connector, which is absolutely not standard. Seems also a Chinese component from the company Palyoo. To solve this issue, is it...

$20 net profit for the seller...

I think I'll watercool the lower GPU only - as it needs to be single slot and will get hotter than the upper GPU. The upper GPU can remain air-cooled with a nice dual-slot cooler. With a dual-slot GPU in the upper riser slot, the volume achieved is a bit wider, due to the height increasing by...

I don't know as the fan of both GPU ramp up and stay stuck at 1600 RPM in Windows, whether it's idle or under load. At 1600 RPM it's not that silent. Could be worse though. There is a French guy making quality custom WB - cheaper than EK ;) I'm planning to put the bottom one under water. 1070...

You're going to change your case design ?

Hi LukeD It's my second successful bifurcation attempt (previous one with a GTX 970 and a GTX 750 Ti and the Amerirack riser) but I never had the chance to try a SLI. I'm going to use that setup for 3D rendering. From what I've read, SLI doesn't work very well though.

C_Payne riser works like a charm !! Asrock Z170 Fatla1ty ITX + i3 7350K + one KFA2 GTX 1070 Katana + one KFA2 GTX 1070 Mini Potato pic just to give you an idea of the volume achieved :)

I'm curious to see how you managed to put a watercooled SLI into 9L watercooled ! I searched for all possible solutions in CAD and the smallest I can manage is 11.5L. With two dual-slot GPU though.

Hi there, Just to let you know that I managed to get it working with the Amerirack ARC1-PELY423-C5V3 bifurcated riser ! - PCIe bifurcated riser : ARC1-PELY423-C5V3 - MB : ASRock Fatal1ty Z170 Gaming-ITX/ac with PCIe riser enabled in BIOS - i5 6400 with 2x8 Go of Corsair Vengeance LPX DDR4 2400...

Thanks a lot ! Just one last dimension if you don't mind :) therminal's height without the fittings. http://i305.photobucket.com/albums/nn203/hagoun/Sans%20titre-1.jpg Thanks but my project is for personal use. I alreadry have most of the hardware :) I ended up purchasing this chassis (which...

That's great chemist_slime ! I registred on the forum just for your project as I had a similar one in mind :) I would like indeed to fit two GTX 970 into a 1U or 1.3U rack mount chassis for GPU rendering purposes. I just purchased at a good price an Asrock Fatal1ty Z170 Gaming-ITX/AC, and an...