Well, the weird thing is when the sysm booted which was every time after being off, when running stability tests like intel burn test, prime 95/orthos etc, there was never any instability. It always passed the tests with 0 errors.
Whilst overclocking I kept all memory voltage at stock, whilst...
Ahh my fault. So the FSB Termination Voltage is the FSB increase. My problem now is, I don't know what they are set to by default as SB, NB & FSB voltages are set to Auto. How can I determine what they are by default? None of the apps I have installed (Asus AI suite, coretemp, speedfan) show...
Ahh I see. I guess the P5K doesn't have this. Settings I have for adjusting voltages:
Vcore
CPU Voltage Reference
CPU Voltage Damper
CPU PLL Voltage
DRAM Voltage
FSB Termination Voltage
NB Voltage
NB Voltage Reference
SB Voltage
I got the impression that maybe the CPU was sucking too much from the motherboard, so the PCIe wasn't getting enough power or something? So maybe upping NB voltage. It's strange as it seemed ok for a four-five days or so then randomly got me on a reboot. PCIe frequency has always remained locked...
Recently been toying around with overclocking my C2D 6420. Started off at 266, long story short ended up at 400MHz stable.. Pc ran ok for about a week. Friday afternoon I did a windows update, rebooted - and I got no display. The fan on the graphics card carried on running at full speed...
You're card is definitely a wrong one, or lack of power or something. My 4870 flies in Cod4 on max settings + aa + af @ 1920x1200. Never once did it ever feel slow throughout the whole game. That was with my processor @ stock (2.13) speeds.
I'm starting to think my card is going faulty. Only had it since end of August (practically brand new) - should be ok to get a replacement right? It's a Force3D one. Now I'm having funny reboot problems with it. I reboot, the fan stays on full speed and I get no display. I have to switch the PC...
Since my last (and first) attempt at upgrading ATI drivers, I can't run the ATI' exe's anymore. I just get "ati install manager has stopped working". Had to use the CMD to force the new ones to install after searching 4 hours. I still can't run the exe's even now - same error message.
I read...
I get a similar noise when the graphics card comes under load. It's worrying but it doesn't seem to affect anything. I just hope it's not bad and doesn't kill the card as it's not a nice noise.
What method are you guys using when upgrading drivers? The last time I tried updating my drivers, after uninstalling, then running driver cleaner, when trying to install the new ones (running the exe), kept getting "ati catalyst install manager has stopped working" error!!
Read loads of...
But surely enabling the voltage damper to maintain the 1.2650Vcore would rectify this?
I just ran 10 runs of IBT. Apparently my system is stable :) I was surprised however, by how much higher it took the load temp. It took it to 50c. First time I have seen the temp go this high!
As per title, at the moment I'm running my E6420 @ 3.2GHz - 400 x 8. I have the Vcore set to 1.28v. Once I begin to run stress tests, the Vcore drops to 1.2650 (Vdroop I guess) but the system remains perfectly stable. Does this mean that I can lower the Vcore so it runs at this all the time -...
After installing my new cooler (Coolermaster V8 - totally awesome) and moving my machine over to a new case (Antec 300) thought I'd try some overclocking.
When fiddling around with the FSB I noticed that at 350FSB, the onboard wireless would not connect to my LAN - windows saying it was not...
80c shouldn't be a worry. The 8.7 cat drivers come with really low fan speed setting. When I played games on this (only got my card 2 days ago), whilst it idled between 78-81 - load only ever went up to 83-85... Use the profile fix to set your fan speed. 30% is a good speed and knocks of almost...
It's late but I think I may give them a go. Currently I can guarantee an atimkdag error if I play ET:QW demo for a little bit. Terrible news about your array going funky. I'm "fairly" stable on 8.7 but I'd like to get it 100%. Suppose I can always roll back to 8.7.
Lol. I got my 4870 yesterday and installed the 8.7 drivers from the official site. Only learned about 8.8 drivers this evening (UK) so spent an hour or so looking for them to no avail. Even came on the forum - but didn't click the VC category, went straight to search. The only place I didn't go...
Hi guys,
Needing to use my com port, have a Port that connects to the header on the motherboard (as it doesn't have a native one). It's detected in Windows fine, but when trying to communicate through it - I get zilch!
Have tried my Cable and thing I'm trying to telnet into etc on another PC...
Sorry to bring up an old subject but I too had issues (scared) pushing the pins in for the stock HSF. I was doing this *outside* of the case. How on earth can you push the pins down if the board isn't slightly levitated? - this makes no sense to me :) If you had the mobo placed on something soft...
I'm assuming EIST is SpeedStep? I've disabled these two (C1E + SpeedStep) and the clocks running @ full speed now.. Though I may just re-enable C1E Halt if it doesn't lose me any performance. I thought there might have been a delay for the multiplier changing or something which coulda caused a...
My fault - just done some googling and found out about C1E Halt and SpeedStep. Disabled them both and seemed to do the trick.
What kind of performance decrease (if any) will I see by leaving C1E halt / EIST enabled?
Recently bought a P5K-E and E6420 from Ebuyer. I've only just noticed that in CPU-Z, it's running at 266 x 6, rather than 266 x 8. Does anybody know why or seen this before? Motherboard BIOS version is 0401 30/5/07. System has onlyl been running for a few days.
Is anybody using Uberoptions mod for the standard Logitech setpoint mouse software? I'm just wondering how I can apply specific bindings for HL2 / CSS (in uberoptions). I've tried the hl2.exe's but no luck. Tried steamapp.exe but no luck.
The problem is I use my mouse4 and mouse5 (thumb...
Which exe did you use to apply specific mouse settings for half-life 2 / counter strike source in uberoptions? I want the Mouse 4 and 5 to be cruise up and cruise down for all applications but for HL2/CSS I want them to be generic buttons (so they're read as mouse4 and mouse5 in the game)...
I...
Cheers for replies guys. Still sorting that pic out - having to reformat again *argh*! Another quick question, does this include 60mm Delta Screamers being attatchable to the board - or would they draw too much current (and mess the board / CPU up) ? If not, would the screamers be ok on a fan...
Hi Guys,
Got a few questions regarding fans. I have a 120mm YS-Tech (very loud but massive CFM) on the side of my case. Which way should it be facing? Should it be extracting air from the case or blowing air ain. It's sat more or less infront of the processor. My guess is that it should blow...
Thanks for the reply dude. Hmm, haven't tried that yet. Will give it a go - just sorting out my case air flow at the moment. It's really strange though, it just doesn't want to go in. And I thought my last sound card had a tight hole...!
Hi guys,
Recently purchased an Asus P5K-E, all running good however, I'm having trouble trying to actually plug in my COAX cable (which works fine on my other PCI SB Live) into the Coax Port (not the optical one). It goes in about a milimeter, then won't push in anymore and I'm scared to push...
Many thanks for the post stenna b - you've been super helpful. I'm glad to hear its not a powerpack issue. So is this double-boot thing random or does it happen only with certain settings? As far as I can tell it's random.
PC is running great, bar this random on off thing so I may just leave it...
My problem, was solved - was the onboard soundcard. Confused 'cos it said PCI.
I have noticed somethign though, sometimes when I push reboot - or save and exit in the bios - the PC actually turns off, then turns back on. Is this normal or am i having power problems?
Hi guys,
Just received my new PC bits today, Asus P5K-E, C2D 6420, Corsair 2GB XMS2 Pro ram. All going good so far however, in device manager, theres a "PCI Device" that isn't installed and I have no idea what it is. The only card I have installed is a cheapo PCI-E 7200 (until I buy my new gfx)...
Well I've decided to purchase the system besides the graphics card (just bought a cheap one instead). Going to wait and see how it pans out - it's only a couple of months so I can survive 'til then :)