Search results

Nice Review as usual. Which CPU holder did this board have? I remember it having the Foxconn and had problems. Have they switched to Lotes?

Anyone have any input on my earlier post in regards to the impulse rate for the DDC and the poweradjust? None of the screenshots show the green flow line changinh, only power and rpm. Maybe it cannot calculate the flow from the pump?

I see this is using 509 impulses per liter. Did this come from Laing? I am interested in this product after messing around with the bigNG stuff by mcubed. They used 509 impulses/minute and did not match my flow from the rpm cable. I read that the DDC gives 2 impulse per RPM. My pump does...

Go to here: http://support.asus.com/download/download.aspx?SLanguage=en-us type in your motherboard.. do search.. and at the bottom of the driver tab is "Makedisk" for which you can download.

Go back to the asus download site and look for a program called "Makedisk" which will make a floppy for your F6 install.

I'm with saan44. What is recommended? First, I want to make sure I did not buy bad ram modules. I think memtest 86 is good for that. It found one bad stick out of two which was giving me some problems. Second, I mainly use P95 and OCCT for stabilty though.

Can you just use plain ol' memtest86 v 1.70 on the newer chipsets. History this program talks about P965 chipsset, but nothing about newer Nvidia chipsets. I am buying 680i chipset and ddr2 ram for the first time and used the bootable floppy back in the i478 days with DDR1. I want to be able...

Exactly what I did. Works fine.

Another alternative - buy a $30 jigsaw and fine metal cutting blade. Tape the area to cut to protect the finish and draw the template for cutting. Measure and remeasure a few hundred times. I would make more squareish holes since they are easier, but a jigsaw can turn quite a bit. Use your...

danny_discus: "The cooling I use is water on both the NB and Processor. I can say nothing better about the Bad Axe 2, its great!" What water block works for the NB chip on the BA2? It looks long ans awkward for traditional chipset water blocks. Thanks.

I was cleaning both BIP2 (240) and GTS with vinegar to avoid the cloudy tubing issue. As above, the tap water test (kitchen sink with rad laying in bottom and water from faucet going in one port) clearly shows the GTS is much more restrictive for water flow. Also, this became obvious by just...

Agree with the BIP2 (240). I have it and the newer GTS and the latter is very restrictive for flow of water. As implied above, more fin density on the GTS would have more fan noise. If you can, try to find the older BIP2. I was in the same boat as you. I have watercooled a...

I think these claims are for "air" pressure drop from the fans which may be true. The fins are much thinner, but more dense and fragile. I do know one thing for sure, there is a lot more water flow restriction in the GTS240 than the BIP2 and it looks as though the 1.2mm wide tubes are...

Not sure about the GTX, but I had a 240 GTS. I was cleaning and soaking my old BIP2 at the same time as the GTS in the kitchen sink. The pressure drop has really increased with the GTS. With a funnel and short piece of hose to fill the rad, the water/vinegar emptied very quickly into the...

Oops, this post should be in here rather than up one level. First time poster - long time lurker. I plan on getting the Asus A8N32 motherboard and SLI GPUs and have a question on single slot gpus (7900 GT) and dual slot gpus (7900 GTX orX1900 XTX). I currently have two Maze 4 low profile...

First time poster - long time lurker. I plan on getting the Asus A8N32 motherboard and SLI GPUs and have a question on single slot gpus (7900 GT) and dual slot gpus (7900 GTX orX1900 XTX). I currently have two Maze 4 low profile gpu blocks and two Swiftech MCW60s which are taller. I also...