• Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
    Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.

Recent content by Wizard!

  1. W

    User Review X79-UD3

    I am getting slow speeds with a usb stick, however it is not an expencive one, thus I thought it is normal...
  2. W

    User Review X79-UD3

    Sorry for digging that up, but I am experiencing problems with my usb 3.0 speed. It is just 10-15mb/s over USB2.0 speeds... I tried both GB drivers and Fresco (from their website), but did not see any difference. Tests are made with external USB3.0 HDD, not flash disk.
  3. W

    XSPC GPU

    Thanx bmoney9 :) Have you checked temps on mosfets? If yes, what soft are you using? I tried GPUz & HW-Monitor however none displays mosfets temps... :rolleyes:
  4. W

    XSPC GPU

    Sorry for bumping this one... I am waiting for a Gigabyte 7970 OC Rev 2.1 to be delivered. Unfortunatelly I did not know that it is not reference designed, so I cannot use a full cover block. I do own Swiftech MCW80, so I can use this one to make it work. However I am wondering if I...
  5. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    After some time, my Perc went off... So, until I receive a new one I had the time to check the mobo. In conclusion, it wasn't Perc's fault, JMicron was bad or damaged and I RMAed the mobo. Today I got the new one, and works fine with or without the Perc!
  6. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    I cannot boot without Perc... Every drive is on it, not just the boot one, however, I can pull him out just to post and see what happens.
  7. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    Maybe it has to do with the Dell Perc5/i that is installed... Some conflict? I cannot see JM on post because P5/i displays its message and it clears the screen...? I do not know. However I still cannot see it under Windows.
  8. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    Just ckecked it... Nothing appears in post screen... :confused: Is there anything else I should enable in UEFI, beyond those three options under Advanced > Onboard Devices Configuration > JMB Storage Controller: Enabled JMB Storage OPROM: Enabled Display OptionRom: Enabled
  9. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    Surly73, thanx for your detailed answer. I cannot see JM neither under IDE ATA/ATAPI controller, nor under Storage controllers. Under the first section there is only the Inter ACHI controller, and under the second the Dell Perc 5/i. Fortunately, following two of your tips, had a positive...
  10. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    I think I will try this first... :rolleyes:
  11. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    Raja, I did all of that... I did scan for hw changes. Nothing happened. I did a fresh install. Was not recognized. Should I enable all three options in BIOS ? I think I have the one of them disable, the one about bootable devices.
  12. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    I recently got my new B3 stepping mobo. Since I own a Perc5/i, and all drives are attached there, I set ICHR to ACHI mode and attached there my DVD-RW and an eSata port that is on the case. I also enabled JMicron in BIOS in order for eSata port on the back to function. However, I am not able to...
  13. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    Ok... After 13 days if trying to set up this board, I managed to do it, with a SATA DVD... It is the only way. I have to remove the 4 disks (RAID5) from ports 2-5 (blue), connect there a SATA DVD, install Windows, and then remove the DVD... I am waiting for an extra IDE/SATA controller to be...
  14. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    bad luck part 12... I managed to get a sata dvd from a friend in order to install Win7, however it does not work... I will have to wait until tomorrow to buy a new one, hoping it will do the job. Unfortunately after installation I 'll have to remove it since I have no empty sata port and the 2...
  15. W

    Official ASUS SSD – P8P67 Series Validation and Support – Including SATA6G SSD

    Well, lets wrap it up... I am trying to set up this mobo 11 days now, but I had no jluck.... I managed to solve this problem, by updating the Intel SSDs firmware with the latest that came out on Jan 26. However, I am still facing problems on installing Win7... My setup consists of a raid0...
See more
Back
Top