• Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
    Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.

Recent content by sitalchauhan

  1. S

    HP ProLiant MicroServer owners' thread

    Just got a N54L microserver and looking to upgrade the ram (Probably don't really need the extra ram since I am not running ZFS but ram is so cheap at the moment I might as well upgrade it). It came with 2gb ECC ram. Can I add another stick of 4gb ECC ram to make it 6gb? Or am I best...
  2. S

    Post your "rate my cables" here

    Here is my Antec P180B that I recently watercooled and modified. You can check my full worklog here if you want: http://hardforum.com/showthread.php?t=1674524 Here is the right side of the case where I have routed all the cables to hide them: And here it is with the side-panel off...
  3. S

    post pics of ur p180/p182/190s

    Here is my ancient P180B that I recently watercooled. Check out my build thread if you get time. I resprayed all of the internals black and made lots of dremel cuts to help cable management: http://hardforum.com/showthread.php?t=1674524
  4. S

    The Post Pics Of Your Rig Thread! - ABSOLUTELY NO COMMENTS

  5. S

    Sital's Watercooled Antec P180

    Here are the temperature stats. All of these are with the e6600 overclocked to 3.3GHz (standard is 2.40GHz) and the 8800GTX core clocked to 626MHz (standard is 575MHz) and all fans running at 7v The CPU air heatsink used was a Theralright Ultra 120 Xtreme Air Cooled Temps CPU Cores: Idle 38 /...
  6. S

    Sital's Watercooled Antec P180

    I wrapped both of my DVD-RW drivers with black electrical tape so that they matched the matt black internals of my case: I then started making my own custom power cable that would be the exact length to power both of my DVD-RW drivers and 2x Sunbeam Rheobus fan controllers: I then...
  7. S

    Sital's Watercooled Antec P180

    I decided the remount all of the heatsinks on the motherboard with some MX4. The heatsink above the cpu slot came off very easily and then I secured it back down with zip ties with MX4 since the original plastic clips couldn't be used again: The large heatpipe system was harder to get...
  8. S

    Sital's Watercooled Antec P180

    One annoying thing with the P180 was that the power and HD leds would flash out of the side even when the front door was closed. So I wrapped up a piece of card with some black electrical tape and wedged it down the edge to stop the light showing when the door was closed: I used a...
  9. S

    Sital's Watercooled Antec P180

    Next I set about cutting up my P180 and respraying the internals black. First I disconnected and removed everything from inside my P180: And then set everything up again outside the case so that I could still use my pc while I was modding the case. I was getting some nice temps with it...
  10. S

    Sital's Watercooled Antec P180

    Next I bought another lot of stuff, most of this is new from online stores. The Swiftech pump and EK X-Top were used but in very good condition. The thermochill radiator was used and in really bad condition - scratched paint and very badly corroded inside, but I got it dirt cheap! As you can see...
  11. S

    Sital's Watercooled Antec P180

    So this is what my Antec P180B looked like to start off with: First thing I did was mark out all of the cuts I wanted to make into the case to help with cable management: I bought some primochill tubing, blank pci plates and EK compression fittings all new: I bought an EK...
  12. S

    Sital's Watercooled Antec P180

    I watercooled my Antec P180B a few months ago (my first ever water cooling build) and took pictures during the process but didn't have time for a build log during. So I thought I would post up the details now I have a bit more time :) I had the bug for doing something with my computer and had a...
  13. S

    CPU Skt775 Backplate Advice

    I am buying an 'XSPC Delta V3' cpu block 2nd hand for cheap. But it doesnt come with a mobo backplate (they never came with one originally even when new). When you read all the reviews about the Delta V3 they mention that you should ideally use a backplate to stop the mobo flexing. I just...
  14. S

    CPU Skt775 Backplate Advice

  15. S

    Mounting a 480 Radiator Externally Using A Radbox?

    I didn't actually notice he was balancing the rad on the shelf! I have decided to just stick with a 360 rad and get some 'EK Rad Holder' brackets to hold it against the rear of my case :)
See more
Back
Top