Recent content by FreeGordonMan

  1. F

    NCASE M1 version changelog and suggestions thread

    If you are trying to gauge interest, I am looking to purchase extra panels. Also on a side note would I be possible to get thicker panels? I remember reading in the original thread that there may have been a tooling issue?
  2. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    Once you have the tools that OverRated mentioned you should be set. If you're having trouble you can always look up a video online as a guide. From what I can remember Lutro0 had a good one. You should be able to get them done in one sitting if you have the patience. I sat down one Sunday and...
  3. F

    Asrock Z87E-ITX

    I have three fans running off the chassis fan header at least 12 hours a day. Still no problems so far.
  4. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    I'm sorry to hear that and wish the best of luck on the RMA. Have you tried other fans on the motherboard header? The pump itself is okay? Please let us know how it goes as many of the NCASE builds are using that motherboard. I've got a PNY 780ti and have had absolutely no issues. It also...
  5. F

    450w SFX for 780ti ?

    I currently have a 780ti with the ST45SF-G with stock clocks on both CPU and GPU. I'm pushing the card's limits playing in 1440p with maxed settings (Black Flag, Metro, Crysis, Far Cry) and have had no issues whatsoever. I have an Asrock Z87e-itx, 16GB ram, 4670K, 2 SSD's, 3 fans, and a pump...
  6. F

    Asrock Z87E-ITX

    Just finished up my M1 build and have noticed the fan control on this motherboard is uses voltage regulation not PWM. None of my fans attached to a Swiftech splitter are able to be controlled using FAN-Tastic Tuning. Does anyone know the amount of power provided by the Chassis Fan Header or...
  7. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    I got mine within a week when Amazon was out of stock. Cable management is a breeze with this set. :D
  8. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    The M3's were the ones I used for the motherboard as well. Happy New Years everyone! :D
  9. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    I have some news for those with the Swiftech H220. If you use the black screws included with the watercooler you can fit the filters in front of the frame between the outer panel but it is very tight. Also be careful not to over tighten these screws as they will cause the center of your filters...
  10. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    I guess so :D. All the holes line up properly and with a little adjustment before you tighten the screws the ports in the back line up dead center as well. The thread inserts seemed fine. I've installed and removed the reservoir a couple times now. Edit: upon further inspection I've noticed the...
  11. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    Upon closer inspection I don't see any stress cracks in the acrylic and from an angle it looks beautiful. I do wish they spent a little more time cleaning the inside of the acrylic :p Reservoir lines up a couple mm above the bottom of the i/o shield I most likely will use some stand...
  12. F

    NCASE M1: a crowdfunded Mini-ITX case (updates in first post)

    Hey everybody, I've been lurking this thread for a couple months now and finally decided to post. First off I want to thank Necere and Wahaha360 for the amazing case. I was on dispatch #26 and received the case on the 24th in Michigan. I appreciate the tremendous effort you two have put forth to...
Back
Top