The Lian Li Gallery

CY ATX 8Pin Female to 8pin Male 180 Degree Angled Adapter for Desktops Graphics Card https://www.amazon.com/dp/B07P5R258Q/ref=cm_sw_r_cp_apa_i_kqA6DbF38QCCW



Unfortunately the two pack comes in two orientations. You'll need to buy two of them and get two one way and two the other way if you have dual connections.

I originally got them because prior to the build because people were saying the ftw3 card is so large that the power cables press against the glass on the o11d. I didn't have a problem, but since I already bought them I just used them. Just put this build together on Sunday. First build since 2012.
This is an old post, I know, but thank you for this. I just ordered a single set and after reading your post I looked closer at the product listing and see what you are warning us about. Ordered a second set. Thanks man.
 
As an Amazon Associate, HardForum may earn from qualifying purchases.
Here's my A05B, my favorite small case still in the last decade.. Went through like 4-5 builds that I finally replaced with a Phanteks Evolv ATX. Still sitting in my living room as the HTPC system recently got a Ryzen 3600 upgrade and watercooling but only a useless 120mm radiator atm lol

240mm rad and gpu block from Aliexpress coming in the mail. I was going to do hard tubing but it was a pita doing my main pc so keeping it simple for this one using extra parts.

View attachment 253543View attachment 253544View attachment 253545

Efficiently cooled with Pepto Bismol~

I like the A05N too, and recently pulled mine out of the closet. I no longer use it, but have been thinking about doing a new build in it -- the only downside is the video card length is limited unless the drive cage is removed, but even then if it's an especially long card it might be tight. Also I never modded it for blowhole fans! D:
 
Here's my Lancool ii Mesh RGB:
20211012_073834.jpg

20211011_192737.jpg

20211012_104134.jpg
20211011_192942.jpg

Specs aren't all that impressive(see sig). I went from a MSi gf63 thin laptop that I traded for a Legion 5 desk top and have been slowly turning into a custom build. Case change wasn't in the plans for a couple of months but scored this for $80 on fleebay due to a typo on the name and the fact that it was listed as damaged. Only damage on it was a broken tab on the HHD cage and the back basement panel was bent in a little.

I wasn't going to use the HDD cave so that was an easy fix and removable. The back panel just took a little bit of pull until it was straight again.

I'm enjoying it. But I was very disappointed to see Lian Li doesn't have a modern version of the v1000b. I love that case we'll have to see if I can dig up a picture of the build I had back when I built my first PC
 
One of the things I didn't like about the mess version of this case is there was no light up mesh like the original version. While back with my old case I ordered a couple of RGB strips that are not the best in the world not very bright.
20211014_101031.jpg

They happen to magnet on the front panel no issues.
20211014_101022.jpg

And provide the glow to the mesh that I desired. I've also ordered the side firing Lian Li strip as well.
 
WIP, but I got some decent core components from a user on here to upgrade my Dad's gaming PC with, using my old Lian Li A05N case. I love the case, but it doesn't really accommodate my current setup well, so here it goes instead. I broke the fan clip for the 120mm fan on the Noctua, but I will get a replacement hopefully soon. This is still using my old GTX 970 haha!

20211106_155434.jpeg
 
WIP, but I got some decent core components from a user on here to upgrade my Dad's gaming PC with, using my old Lian Li A05N case. I love the case, but it doesn't really accommodate my current setup well, so here it goes instead. I broke the fan clip for the 120mm fan on the Noctua, but I will get a replacement hopefully soon. This is still using my old GTX 970 haha!

View attachment 413453
Love that case. Have an A04B myself I should probably clean up and put on here sometime.
 
Here's my Lancool ii Mesh RGB:
View attachment 402620
View attachment 402621
View attachment 402622View attachment 402619
Specs aren't all that impressive(see sig). I went from a MSi gf63 thin laptop that I traded for a Legion 5 desk top and have been slowly turning into a custom build. Case change wasn't in the plans for a couple of months but scored this for $80 on fleebay due to a typo on the name and the fact that it was listed as damaged. Only damage on it was a broken tab on the HHD cage and the back basement panel was bent in a little.

I wasn't going to use the HDD cave so that was an easy fix and removable. The back panel just took a little bit of pull until it was straight again.

I'm enjoying it. But I was very disappointed to see Lian Li doesn't have a modern version of the v1000b. I love that case we'll have to see if I can dig up a picture of the build I had back when I built my first PC
I love this case.
 
I love this case.
Ive been enjoying it. Still need to spring for a proper motherboard for it and want to swap the multi color vinyl on the GPU for white. I've also added white vinyl to the inside under where my 24 pin connector goes and a few other custom touches
20211015_120743.jpg

PXL_20211109_191623020.jpg

PXL_20211028_225647047.MP.jpg


Getting rather handy with my wife's cricut machine. I'd like to replace the Pokemon with a Futurama theme something but they're hard to find and getting kind of expensive. I'll have to grab a current back panel pic next time the back is accessible it's currently living in our living room for use on the big TV.
 
Near finished now, with MSI 3080 with EK quantum Vector Trio water block and EK backplate, AQ OCTO controlling fans, with AQ flow sensor connected to OCTO. Corsair sleeved cable kit.
IMG_0265.JPG
 
Purple is the new red.
Purple has always been my go to. Got tired of it in my case and pulled the purple and black cable extensions and switched the lighting theme to mostly off.

A couple of updated pics of my Lancool II
821796_PXL_20230312_012056059.jpg

New GPU(RX6600), vertical mount and dusty glass. As stated above I pulled the purple/black extensions. Debating on getting a right angle adaptor for the 24pin or trying to find a 24 pin extension with a right angle on it to pull it behind the white bar. I may make silhouette of the main cast heads to go down the white bar as well as my Bender and Fry figures went missing after swapping out the motherboard last year. I got tired of the solid white did stencils for the side vent and
335428281_171441312344663_7615290106763829767_n1.jpg

Front. I mad end up wrapping the white parts behind both with black just to help blend it in(its really apparent when all the rgb is on). I'm digging the white and black theme with it and have been trying to find someone with a black case to trade me top filters to finish it off
335532646_228336469574795_8662971964685500776_n.jpg

As promised a while ago a pic of the back panel
 
I do like being able to make my own decals, from through process above to
PXL_20230313_025657326k.jpg

Decals made, to
PXL_20230313_032731562fg.jpg

Placed. Loving how this looks. Next move it so reroute the 24 pin and usb c connectors or see if their are safe right angle adaptors for them

Edit, moved the 24 pin and usb c.
336361113_169484009269219_1499561114701463326_nertyui.jpg
 
Last edited:
336169064_1562239990919308_56178977086252FXGCVB9380_n (1).jpg

Found them!!! They were hiding in the cox of cables. The sand thing isnt Futurma themed. It's something that my 6yr(then5) made for me at a school fair and asked if it could go there. Can't say no to that.
 
Ok crap pics, but pics of my old v1000b
340131696_204157582370489_8988615528100701614_n.jpg

In its final form. That AIO(ish) was interesting, game with a loud AF 80mm fan and cooled worse then the Zelmen cooler I had in it before
339818545_756140839438036_4653037401308635655_n.jpg

Before the water cooling, but in all if its UV CC lighting glory

340073492_526667559436730_2995053476680895349_n.jpg

My modern setup with new deskmat, keyboard and modded my butcherblock desk, rounded all the outside edges, filled in old through desk monitor mount and wire management holes, stained and sealed it
 
Back
Top