Search results

Good info. Thanks J32P2006.

I just disconnect the lines running the exos. They close off as soon as you pop them out. I then just unscrew the connection to one of the barbs and drain the system into a bowl. It is just less hassle for me to do that then having my water block and gpu block dangling over the side.

The only bad side I see to it is if it is like the new Koolance cases. They have the 3/8 plumbing but still only use the low flow pumps like the original. So you are kind of SOL if you want to cool your GPU. Koolance does not make a GPU cooler for 3/8 plumbing and most other company’s blocks are...

In browsing around I ran across this link. It is a sticky over at Anand’s site and is a good read. It might make you feel better.

The Abit board is known to be picky when it comes to ram. Like I said I have the same board and I can not do 250mhz, but I was able to do it my Epox board. I don’t think it is that bad of a hit for the memory to be at 400mhz vs 500mhz. I rather get the extra clocks out of the CPU.

You can try to loosen up your mem timings some and see if that helps. Try 3-5-5-11. Also I run my ddrv @ 2.80 and vcore @ 1.55. if that does not work you will probably be stuck with the 333 divider like I am. Which is not that bad since the mem controller is onboard the cpu.

I was just wondering what makes a fan gay? :D

I would get stable at 250 before I went any higher. Try this. Set your FSB back to 250 and your HT to 4. Then lower your ram down to 333. with the FSB at 250 the ram will still be around 400mhz. Now to run prime and see if you are stable. I have the same board and ram with a 3000+. My Epox...

Does the 120 fan plug into the mother board header? I had a strange problem with my latest motherboard. It is Abit AV8. Installed everything booted her up and she would shut down during post. I could not figure it out. Until i started going through the bios and noticed that that the there was a...

I have one and it works great. No problems yet. I read all the bad press on this board and others about this unit and was a little nervous with my purchase. I bought it anyway and it has worked flawlessly so far….

I had a similar problem and it turned out to be a bad powersupply. Keep in mind you just added some extra load with exos. 3 fans and 2 pumps. I would check the powersupply before messing with the card. I have the same setup and know what it took to install. It would be pretty hard to screw it up.

It is pretty much plug and play. I could not be happier with how it has been performing for me.

Posted this in the other thread also, but thought way not post here also. AMD64 3000+ (250x9) with a 6800GT (450mhz and 1.20ghz) kept cool by the little EXOS that could.

Try loosening up your timings some. I had to loosen up mine to get to 250mhz. I also dropped my HTT to 4x

The LCD has 3 inputs on it. I use to have the 3 monitors on my desk, but it was just to much. Now i switch views with the lcd or just use remote desktop (if you look at the desktop you will see all three rigs up). The green rig is for gaming the others are just for messing around with and...

I am sure there is high end air cooling that can keep up with the Exos, but the noise would be far greater. It keeps my cpu and gpu pretty cool. cpu (amd64 at 250x9) idles around 32c and 41c under long duration loads. The gpu runs a little hotter at around 45c (core 450mhz and mem 1.20ghz). I...

AMD64 3000+ (250x9) with a 6800GT (450mhz and 1.20ghz) kept cool by the little EXOS that could.

Just moved in the new place a 2 months ago still don’t have everything setup, I like the Super Lanboy cases :)

I have the an Koolance Exos and love it. Very easy to setup and move from case to case. All my rigs are in super lanboy cases so there was not a lot of options unless i wanted to cut or cram a lot into the case. I am cooling my AMD64 3000+ (250x9) and my 6800GT (core 450mhz + mem 1.20ghz) with...

I believe he is talking about a car stereo cd player ??????

I got the EPOX for x-mas. I asked the wife for it and the amd 64 3000+ after reading this article at Hexus So far it has done really well. I did not want to push my luck to much so I am just running it at 250 x 9. I am only seeing temps of 41c at heavy loads. The onboard sound is 10 x better...

The koolance blocks should work with that system. Check them out.

I doubt you fried your cpu that fast. I have my 3000+ running at 250 x 9 with no problems. Sounds to me your bios my be stuck at those settings and something does not like that fsb spd.

250mhz x 9 = 2258mhz it is running really cool 34c at idle and 41c under heavy load (CS:S). board is a EPOX / EP-9NDA3+ cooling is from a Koolance EXOS My biggest limiter is my ram. I am running 2 x 512mb sticks of Patriot PC4000ELK

Nothing at all ?

I am looking for pictures of a W/C setup inside a Lanboy case. I did a search and only found a setup with Koolance system on top. I am thinking of going with the Dangerden kit below. A64, TDX, Lucite M4GPU Black-8 RAMsinks-Alumina Epoxy 1/2 OD, Xtreme BLUE, 120m Evercool DD12V Pump 7 ft...